Lexus SC430 :: Removed Front License Plate - Filling Holes In Bumper?
Sep 20, 2013
replacing the entire front bumper.I have removed the front license plate holder, and would like to fill the holes where it was screwed into the front bumper.
View 8 Replies
Advertisement
I plan to remove the front license holder from my car, fill the holes, and paint/clear coat/sand them. Any recommendation as to what to fill the holes with (I'm not going to use a plug.) Exactly what the bumper cover is made of, I can find the right material to bond to it.
View 2 Replies
How do I get rid of license plate holes on my front bumper? I took my front plate off and now I am stuck with annoying holes drilled into my front bumper. Its not noticeable but i know its there so it irritates me.
View 4 Replies
I need to mount a plate on front bumper and there are dimples for 2 holes. Do I just use self tapping screws here as I've read you don't need a mounting frame?
View 3 Replies
I just bought a 2011 GTI in Steel Gray Metallic. The first thing I did was remove the front license plate holder.
Doing that revealed 3 large holes (about 8mm), and 2 small screw holes. I'd like to repair this myself or have a shop do it.
Is there a relatively easy way to fix this myself (other than putting the holder back on)?
View 8 Replies
Where the license plate lights get thir power from? I have a 2002 SC430 and the plug is just dangling. It goes behind the plate and then if I look under the car, it is just there by the bumper and I cannot find a connector that it can reach.
View 3 Replies
I bought the car from dealer, there are now FOUR! holes on the front bumper. I don't understand why they couldn't just use the existing holes to put the license plate holder. Now I'm stuck with these holes and I'm looking for a cheap alternative to fill them. I like the clean look of the front end without the plates and don't want to spend a fortune at a body shop, but I also don't want 4 dots either. What I can do/use?
View 3 Replies
After going through the car wash several times now in my 2010 RX 350, my front license plate has been bent in all different directions. Car wash guys say it's due to not having a full plate holder, where as 4 screws secure the plate vs. only the top 2 as we have. Any plate holder from another vehicle that I might adapt to overcome this?
View 14 Replies
I have a 2010 RX450h and live in Minnesota where it is hard to hand wash my car. The darn car washes tend to catch the front of my license plate frame and bend it and the license. I have tried several different plate frames and none worked. Minnesota plates are now the thin, non-stamped plates so they are very flimsy.
I even tried putting a plastic plate behind the license to make it more rigid but that failed too.
View 1 Replies
yesterday I got the idea to move the plate bracket on the front all the way down so it gives it a much cleaner look and doesn't obstruct the grille. To do so test mount the bracket on the lowest position, then have someone hold it. Then you take a 1/8 drill bit and make the two new wholes then put everything back together.
View 8 Replies
Was parallel parking today, and bumped ever so gently into a person license plate and it scratched my bumper. Not too bad, but I notice it of course. The scratch is about an inch or so long. Are there any quick fixes to buffing this out. I have touch-up paint, but I'm afraid that will look sloppy.
View 14 Replies
I need to put a front license plate on my Prius. I notice there are a couple little indents on my front bumper but no holes . Do I need to drill holes or something else here to mount a plate ?
View 13 Replies
What I should use to fill the holes on my front bumper? I know how to get paint to make it blend in but what should I use as a filler?
View 1 Replies
Mounting front license plate somewhere other than the "official" mounting location? I don't like the thought of putting holes in my front bumper. I can move it down a bit such that the holes are in the bumper just above the air opening. So, they would be less noticeable. This would block some of the airflow through the lower opening. But, unless I'm driving in 100+ deg temps, it probably won't matter.
I could also offset it to the right or left in the lower opening.
View 14 Replies
had a couple questions about installing the front license plate. I currently do not have any holes drilled in the front bumper (though I can see the places where they are supposed to go). I have the black plastic attachment. What is the best way to drill those holes? Can it be done if I don't have a drill (i.e., just with a screwdriver and force)? Is this something the dealer might do for free (I don't have a warranty, bought my car used)?
View 9 Replies
Ok, Im trying to get my front licence plate holder off. I've looked in all the DIY forums and cant find what im looking for. My question is how do i get this thing off?? I've took the two screws that hold the thing to the bumper off, and its still soild as before i took the screws out. Is it held on by the rub strip?
View 24 Replies
How do I change my license plate bulbs in a 2010 ES350? I bought some 194 JDM Astar LEDs. I took off liner and changed backup bulbs but can't figure out how to change license plate bulbs.
View 4 Replies
I'm in the process of replacing license plate bulbs. I broke the old housing for one of the bulbs so I bought new LED lights on eBay and they came with the housing. The problem is, I can't get the cover to stay clipped in to the tailgate. How to get the lights to stay in? What am I doing wrong?
View 7 Replies
I'm trying to change my license plate bulbs to LED but cant figure out how get to the bulb. I've already removed the carpeted cover but cant seem to figure out how to get the bulb out..... 2007 ES350....
View 3 Replies
I wanted to change my license plate bulbs to LED's. Can't figure out how to get to them. The book says have the dealer replace these bulbs if burnt out. I Always like to try to do things myself.
View 7 Replies
I try to install LEDS on it and I guess I accidently blew the fuse and when I try to search for it, I can't locate it.
View 3 Replies