Lexus SC430 :: Oxygen Heater Circuit Malfunction - Code P0155
Oct 4, 2011
SC430 came up with the check engine light, showing a "Oxygen Heater Circuit Malfunction", code P0155 (bank 2, sensor 1). Searching, I found out this is the oxygen sensor in the passenger side exhaust manifold.
My car is high mileage (over 130K), it's hard to justify purchasing a $230 sensor and paying for installation. My only goal is to keep the check engine light from turning on and passing state inspection/emission (the check engine light will prevent passing inspection/emission in my state).
View 12 Replies
Advertisement
What can be done regarding these faults? P0037 and P0057
Description:
Oxygen Sensor Heater Control Circuit Low (Bank 1, Sensor 2)
Oxygen Sensor Heater Control Circuit Low (Bank 2, Sensor 2)
The catalytic converters have been removed but the fault was present before that anyway. All I want is the VSC function to work again and the lights to go off. I have heard you can put dummy sensors in.
View 3 Replies
I have a 1996 Ford Explorer Eddie Bauer Edition 5.0, the check engine light is on and my code reader gives P0161 and P0155 both stating that the O2 heater circuit sensor is bad. I replaced all 4 of the O2 sensors in the truck, cleared the codes but they still keep coming back. I have tried for a few days now to find something online similar to this but have had no luck. I am not sure what else to do.
View 1 Replies
CEL/OBDII code P0141 - O2 Sensor Heater Circuit Malfunction
So I just bought this car 64k well maintained but cant get rid of the check engine light. Replaced downstream O2 sensor with no luck. As soon as I get home I'll check voltage @ connector. Lets test the O2 sensor connection and test the pins to make sure there is no break in the wires.
View 17 Replies
Just got a P1135 Code on the 1MZ-FE 2002 Camry.
My code reader pulls it up as (no typo below) : AirCFuel Sensor Heater Circuit Response Malfunction.
So I know it's a bad Air/Fuel sensor. Which one though? I replaced the rear sensor by the firewall about 6 months ago which fixed the check engine code (I don't remember the code). Would it make sense that the front one failed now or the back one failed again? Most of my research points me to a bad rear sensor however a lot of people also report that a code reader would report the sensor as "Bank 1 Sensor 1".
The rear sensor was replaced with a Denso 234-9042 Sensor.
I would play the replace and test game... however inspection is due within the month and after resetting the code, it usually takes about 50 miles to return. Being in college, 50 miles takes about 2 weeks.
View 4 Replies
Replaced my post cat drivers side O2 sensor tonight because I was getting zero voltage and a p0430 code. This is bank 2 sensor 1.
But I'm still reading zero voltage!! How could I still be getting zero voltage?? I checked the connections and they are firm. Checked every single fuse in car.
After my recent accident, the center console lights don't illuminate. My nav door doesn't close too. Could these all be related?? The connector for the O2 sensor is right next to the console, so maybe there is a loose connection or plug or perhaps a stray ground?? I do have wires all over the place in under the shifter bezel from aftermarket stuff..
View 14 Replies
P0032 Oxygen Sensor Heater Circuit High Voltage (Bank 1, Sensor 1)
I have read that in 2005 chrysler changed the ohms levels for the oxygen sensors and may need to have bcm reflashed to get a new oxygen sensor to work wheither its dealer item or not, is this true if i were to buy a mopar oxygen sensor? aftermarket is out of the question being the ohm readings would require me to spend some time at the dealer. is this code a defective sensor? or could it be related to the thermostat being faulty? am not low on antifreeze and temp gauge reads normal.
View 3 Replies
I have a 2007 ES350 with 90k miles. Purchased in August. I had ignition coil go out and decided to change them all and the spark plugs. When changing cylinder 5's coil and plug, I tried to push the wiring harness out of the way to remove the coil. Result, I moved the wiring harness too far and disconnected the 3 wires (black, yellow and red) that were connected to the cam position sensor connector. (I should've just removed the sensor SMH) I disassembled the connector, got it down the internal pins, soldered the pins to the wires, placed the pins back in the connector and reassembled it with the wires in the order that they appeared to originally be.
Plugged it back in and put everything back in place. Started the car and code P0352 was cleared but replaced with code P0365 Camshaft Position Sensor B - Bank 1 Circuit Malfunction. I'm thinking, either I put that pins back in the wrong order or one of the wires isn't properly soldered in. Either way, I ordered another connector and it should be here tomorrow. I need Either a wiring diagram or a picture of the camshaft position sensor closest to cylinder 5 connected with the wires in the proper order .
View 14 Replies
I have a 2000 motorhome on a f450 chasis. It has a V-10 with only two oxygen sensors up-stream from the catalytic converter. The monitors for the oxygen and oxygen heater sensors will not show "ready". I replaced both sensors and have driven it over 200 miles. They still show "not ready".
View 5 Replies
I have some codes on my ranger 2000 here goes
P0141: o2 sensor heater circuit malfonction (bank 2 sensor 2 )
P0455: evaporative emission control system detected (large leak)
Now I will need to get that fixed cause I don't know where to look and what to look for ... For the leak I know there is a big crack on the plastic where the gas lid is could that be it ?
View 2 Replies
My 98 blazer (130k)recently started showing code p0740 tcc circuit malfunction..
The truck runs fine (except for the water pump I just blew) this is a tranny solenoid code. but my tranny seems to be shifting ok..
Is the solenoid easy and cheap enough to replace myself? I am trying to make up my mind if its time to start thinking of trading this blazer in on something with less miles or to fix it up and keep on trucking..
View 4 Replies
I have 94 SE camry with the 3.0L V6 1MZ-FE engine and has individual coil packs. I'm getting a P1300 Igniter Circuit Malfunction. I have checked it out per the procedures EG2.pdf. I'm down to step 8 and the voltages are little different between the 6 points. started checking out the ground at the ECM per IN36 instructions. it appears that from pin #27 & 28 are not grounded to the ECU case.
View 5 Replies
After about 6 months I finally got the alternator replaced in the Tribute. I totally forgot about the CEL that was on for EGR Circuit. I've found a couple of pages ( OBD-II Trouble Code: P0403 Exhaust Gas Recirculation Circuit Malfunction ) that explain how to diagnose the issue but I was wondering if any other route for something that may be more common than another thing.
View 2 Replies
This is what I get from the DTC .....
DTC P0705
Description : transmission range sensor circuit malfunction
State : History
I have done some google search on the above diagnostic trouble code P0705 and as i understood , it indicates that the Engine Control Module (ECM) has received an input error from the Transmission Range Sensor (TRS).
Since the check engine light illuminated two times (two separate occasion) then it turns off now; the ECM is actually receiving input signal from the TRS.
So that leads me to think that the TRS is actually working but the problem might be one of the following two:
1- Open or short in the TRS circuit?
2- Dirty transmission fluid.
What do you think the steps i should do first of all ? how would i check the transmission fluid since my vehicle has no transmission fluid dipstick. My driving condition would fall into "severe" category and it reached 60,000 miles now ...
View 10 Replies
Got the CEL Bank 1 Sensor 2 heater circuit fault. Is that the rear right post-cat oxygen sensor? What is correct part number or possibly a link? 2002 2.8l Passat V6...
View 3 Replies
The 2005 Avalon has 48K miles and it's been running well without any issues, until today.
Driving in city traffic, max speed is about 30 ml/h, The "Check Engine" light and the "VSC (Vehicle Slip Control) Off" lights came on. I did stop the engine, restarted after couple of minutes and the same lights stayed on. The car ran just fine, no noticeable difference in performance.
With the OBDCOM reader, the Avalon has this code:
P0351 232
P0351 Ignition coil A primary/secondary circuit malfunction
That seems to indicate a malfunction for cylinder A, or #1, ignition coil that has nothing to do with the "VSC" AFAIK. Is this a misread by OBDCOM reader, or the Avalon is confused?
The code had been reset via the OBDCOM reader, the car runs fine, neither of the lights come on now. Should I do something about coil A, or just wait until the code comes back?
View 1 Replies
I have a 2003 Santa Fe, V4, 2.4L.
So the other day, my CEL and I got it scanned: p0320, or "Ignition/Distributor Engine Speed Input Circuit Malfunction."
It was accompanied with two symptoms:
1. The car will sometimes sputter on startup, and the tachometer will be zeroed out. I have to turn the car off and turn it back on, and it will start normally, albeit with a bit of a misfire on idle.
2. The car will sometimes die while at a stop. Just like the first symptom, if I turn the car off and turn it back on, it will work normally.
I looked on here, and it seemed like everyone solved a p0320 by replacing the Ignition Failure Sensor. So that's exactly what I did. But nothing changed; I still have the symptoms, and the CEL came back on and is still reading p0320.
What should be my next step? Could it be faulty wires that give power to the Ignition Failure Sensor?
View 3 Replies
I have a 2002 Jetta 1.8t. My check engine light came on and it gave me the code P0135 sensor heater circuit. Bank 1 Sensor 1. We bought a new 02 sensor and replaced it. We definitely bought the right one too. Cleared the codes. After a little driving the CEL came back on with the same code P0135. What is wrong and how I can fix this?
View 6 Replies
Just started the truck after not running for a few weeks and drove around fine. Looked down and suddenly a CEL was indicated. Checked it with my Edge Evolution diagnostic mode and Code P0161 came up 2nd bank downstream heater circuit fault. I've also have an exhaust leak in the right passenger side exhaust manifold for about the last year. I've been waiting to install my newer 03' used engine when time and funds permit.
View 3 Replies
I have a 1999 Ford Explorer with the V-6 SOHC that is stuttering and stalling when I try to accelerate. A very slight acceleration will get the vehicle moving, but anything coming close to normal gas pedal pressure causes immediate stuttering and/or stalling. Check Engine light came on when problem started yesterday.
Where is the EVAP System Canister Vent Solenoid? I bought a code reader after beating my head against the truck all afternoon and got code "P1451 EVAP System Canister Vent Solenoid Circuit Malfunction". My Haynes book says on the left side frame rail... can't find anything along there that looks like it (based on picture from Rock Auto for replacement part) and found some people online talking about it being in the engine compartment on the passenger side...
Just crawled all over the truck and I think I found the charcoal canister, but couldn't trace it back to the vent solenoid... There was something right next to the canister, but again, it looked nothing like the replacement part listed on Rock Auto...
View 14 Replies
Yesterday driving to work felt the engine missing, on the way home got a CEL pulled the code when I got home it was P0302, so I started with the easy and put a new coil pack, same issue, so I prayed and pulled the plug (it didn't break). Put a new plug and a second new coil pack (just to be sure, and yes I keep extras dang 5.4). cleared codes and started it this time got P0202 Ford - Injector Circuit Malfunction Cylinder 2, so I checked Ohms on #2 and it was 12.6, #1, 3, 5,6 all have 13 Ohms, didn't check #4, 7, or 8 because my big hands and the probes on my multi meter. Checked the wires on all of them and have 12 volts with key on, not running. I read another check to put blk in pin and red on pos batt terminal, and that it was supposed to go 12 to 0 off and on with engine running, All of mine went up to 14 volts and stayed no switching. Is there something I am missing to check before replacing the injector on #2?
View 6 Replies
