Lexus SC430 :: New Oxygen Sensor Reading Zero Voltage - Code P0430
Aug 17, 2015
Replaced my post cat drivers side O2 sensor tonight because I was getting zero voltage and a p0430 code. This is bank 2 sensor 1.
But I'm still reading zero voltage!! How could I still be getting zero voltage?? I checked the connections and they are firm. Checked every single fuse in car.
After my recent accident, the center console lights don't illuminate. My nav door doesn't close too. Could these all be related?? The connector for the O2 sensor is right next to the console, so maybe there is a loose connection or plug or perhaps a stray ground?? I do have wires all over the place in under the shifter bezel from aftermarket stuff..
View 14 Replies
Advertisement
Just read that a clogged EGR valve is common and reduced performance and increases emissions. Need to clean this valve? Where is it located?? Just noticed tonight that there is not a lot of suction from my vacuum lines and I wondered if this is related. Plus I have a p0430.
View 3 Replies
SC430 came up with the check engine light, showing a "Oxygen Heater Circuit Malfunction", code P0155 (bank 2, sensor 1). Searching, I found out this is the oxygen sensor in the passenger side exhaust manifold.
My car is high mileage (over 130K), it's hard to justify purchasing a $230 sensor and paying for installation. My only goal is to keep the check engine light from turning on and passing state inspection/emission (the check engine light will prevent passing inspection/emission in my state).
View 12 Replies
[URL] ..... I had the P0430 code come up in my 06 GS300 AWD so i changed both passenger side 02 sensors. i followed the above instructions on changing the pre-cat sensor, changed my 02 sensor plugged everything back up and the P/S light came on and i lost power steering. I unplugged and checked everything at least 10 times until i finally gave up and gave it to lexus today. been about a week though driving without power steering. I know I did everything right and plugged everything snug. Did my P/S just decide to die?
View 6 Replies
y '02 SC430, which had been in an accident, is throwing a low voltage code and showing the airbag light. What was the reason for the code (C1336)?
View 6 Replies
P0032 Oxygen Sensor Heater Circuit High Voltage (Bank 1, Sensor 1)
I have read that in 2005 chrysler changed the ohms levels for the oxygen sensors and may need to have bcm reflashed to get a new oxygen sensor to work wheither its dealer item or not, is this true if i were to buy a mopar oxygen sensor? aftermarket is out of the question being the ohm readings would require me to spend some time at the dealer. is this code a defective sensor? or could it be related to the thermostat being faulty? am not low on antifreeze and temp gauge reads normal.
View 3 Replies
After not driving the car for over a week, the battery was dead and I discovered that I had not fully shut the trunk. I hooked up a charger/maintainer with the battery still installed in the car and it has been on for 48+ hours and it still shows as charging. I have several of the chargers and use them on other cars/motorcycles where they work as expected. I've never had one take this long to indicate charged.
I'm sure others are using maintainers and wondering if it is normal that the charger does not indicate full charge. Voltage with charger running is ~14.7 and ~13.7 unhooked. I believe it is a 4a charger.
What is normal voltage when fully charged and what is minimum voltage to crank starter?
Should have measured the voltage before hooking up the charger to know low it was......
View 6 Replies
I have a 2010 Toyota Corolla 1.8L, the base model.
I recently had a check engine light, VSC off light (blinking) and traction control light come on. I took it to Autozone and had a p0037 code ring up for a new Bank 1 Sensor 2 oxygen sensor (downstream). I believe I have found the correct sensor (located under car, approximately near drivers seat) and it looks simple to replace, aside from the fact that the wires go through the car body.
Can confirm that I have located the correct sensor? And if so, what is the best way to get to where the wires connect?
Is it located under the drivers seat? What should I do about the rubber grommet located under the car where the wires appear to pass through?
View 2 Replies
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 Replies
My Jetta has been throwing this code on and off for over a year now. It used to only come on when it was really cold with wet roads. Now the code will randomly come on in any weather. I usually just clear it but it's coming on to often now. I don't notice any performance issues or gas mileage problems.
Scan shows : Trouble Code - P0420 Catalyst System Efficiency Below Threshold (Bank 1)
I've been reading and apparently 1.8t engines only have One bank? I'm assuming this the the front 02 sensor throwing this but not sure?
I have an aftermarket exhaust/high flow cat. Apparently this can be caused by a high flow after market catalytic converter and one solution is to use a test pipe or spacer to move the rear O2 sensor further from the exhaust gas flow. But I'm not sure this is the issue since I think it's my front sensor throwing the code? That's not by the Cat is it? I just don't want to have the sensor replaced to have the code still come up.
View 5 Replies
I received error code P0031 on my 06 Avalon the other day. It states that the HO2S (Heated Oxygen Sensor) is bad. Bank 1 Sensor 1. I located the sensor but have a few questions...
Just to give an over view for those that don't know where these are, there are 4 sensors the one in the front on the manifold (upper - B2, S1), (lower - B2, S2) and the rear manifold (upper - B1, S1), (lower - B1, S2).
All of the sensors look the same with 4 wires. what the part number is for the sensor? Also since this is the hardest one to get to, I would like to know where the wire routes to. I found the wire up to the connector on every other sensor except the one I need (B1S1). It looks like it runs towards the top of the engine but from the top I don't see it.
View 2 Replies
I have a 2001 Exrursion 5.4L V8. The code P1131 comes up and it says "Lack of upstream heated oxygen sensor switch - sensor indicates lean - bank #1". I hear it could be the sensor that is bad or there is a vacuum leak. It runs like a champ, no spitting, no sputtering, no missing, no ruff idle. What do I need to do to fix it or where do I need to start looking?
View 3 Replies
My car is running great, no issues. I just changed the ignition coils, i was having a misfire. It was easier since i was changing the back to replace them all. My CEL and VSC went on and it is code P0430 bank 2. Before i spend a ton on a new catalytic converter i would like to change the o2 sensors. Problem is, I am not sure which ones to change or where to start. Is this even something i am able to do?
View 2 Replies
I have a code reader got P1193 - MAF sensor low voltage
Is it shot or just need cleaning? Or is it something totally different
2005 Santa fe 3.5l
View 2 Replies
1993 ford explorer sport... I got an error code for a low voltage MAF sensor. how would i go about fixing it? Do i need to get a new MAF sensor?
View 1 Replies
I drive a 1998 Jeep Grand Cherokee, 6 cylinder engine, with about 120,000 miles on it. I used a code scanner and pulled a P0138 code-bank 1 sensor 2 O2 sensor high voltage, if I'm correct. First of all, it looks like this sensor is after the catalytic converter, right? So I think I either have a bad 02 sensor or a bad catalytic converter. What are the consequences of driving around without fixing this? Will I see any reduction in fuel economy, or any potential long-term problems elsewhere?
View 2 Replies
SO all three lights came on and wouldn't go away.
Ran a scanner for code and got p0430.
Took it dealership for estimate or fix.
Go figure : code summary: Causes.
Reported fixes or Causes: for code p0430
- catalytic converter has failed.
- Air fuel ratio sensor
- Bank 2 cat converter
- Bank 2 (A/F) ratio sensor
- Oxygen 02 sensor
- downstream Oxygen 02 sensor
- Exhaust pipe
- Mass Air flow sensor
So I am waiting thinking ok let be one of the above causes or fixes that is cheap.
View 4 Replies
What can be done regarding these faults? P0037 and P0057
Description:
Oxygen Sensor Heater Control Circuit Low (Bank 1, Sensor 2)
Oxygen Sensor Heater Control Circuit Low (Bank 2, Sensor 2)
The catalytic converters have been removed but the fault was present before that anyway. All I want is the VSC function to work again and the lights to go off. I have heard you can put dummy sensors in.
View 3 Replies
I got a P0430 code. My fuel trims are over 20% on both banks. A few days back I got a P0174 code but after disconnecting the battery it cleared and hasn't come back. Are these codes related in any way?
I'm a bit confused because I removed both cats and put O2 spacers in on both sides. I never get a P0420 code. Is one of the spacers not working correctly? I sent Toyota an email about the 430 code and they want to know which of the cats were removed - front or back. I didn't even there were front AND back ones! I thought there were just 2 side by side.
When I analyze the O2 readings on Torque they look pretty similar for both banks although I admit I'm not the best person to judge. Both rear O2 sensors are fairly new.
Unfortunately living in the middle of Africa I can't get hold of a smoke machine. I'd love to look for a vacuum leak, as from what I've read about the subject this might well be the cause of my problems.
One mechanic wants to put a new fuel pump in but I'd like to postpone that because it's a pricey item.
View 11 Replies
My Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 Replies
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
View 1 Replies
