I just got my car back from a body shop, after they fixed all the rock chips on the front. Now I realize the seat position memory is not working for both the driving and passenger seats. Not only the button does not move the seats, but I can't set the new positions into the memory either.
View 2 RepliesI picked up our ("our" means my wifes) GX last Friday. I'm a sports car and sports sedan guy. But I love buying vehicles, and I a huge car nut. It's a heck of a nice Luxury SUV with a lot of nice features.
One question so far. The web site specifically says the passenger seat position can be saved to the memory, but for the life of me I don't see how. Can it?
New owner of 2014-RX350. I have figured out most stuff simply using the owners manual (go figure), but this one continues to stump me, as I have repeated the procedure right out of the owners manual without success.
Manual states to have only one fob or card present, car in park, "ignition on" position (I interpret this as two pushes to the ignition switch), push desired memory button and hold while pushing either lock or unlock button till chime sounds. I get the chime. But when I lock the door, wait a minute, and unlock the door by touching the handle, the car unlocks just fine, but seat does nothing. When I manually push L2 (in my case), the seat does indeed move into position. But I cannot for the life of me get this function to work.
What gives? Tire pressure light on but the system is disabled
View 10 RepliesOn several other cars I've owned it was possible to link a key fob to seat memory. Meaning if my wife used her remote fob to open the car doors the seats and mirrors were set to her memory position etc.
I searched the owner manual and don't see this feature on our SC430.
How I can go about programming my smart key remotes to the memory positions of the vehicle? I had it all set up from the dealer and since then they had to disconnect the battery for something and now I don't have that feature. It was setup where I can walk up to the car and unlock it by the remote or door handle and it would put the memory position to that remote?
View 4 Replies135 plus pound passenger with seat belt on. Was intermittent on/off with passenger but now seems always off (off light 'on' ) meaning the passenger airbag is disabled.
I know the es350 was so bad like this that there was a threat of class action. I've read the weight sensor is in the passenger seat rail and you can also do a calibration with a scan tool.
Dead battery. After recharging it, the car starts but.......
1. the seat memory buttons stop working
2. the radio that hasn't worked in 8 months since i own the car is working
when the radio wasn't working, i tried to put in new fuses and that didn't work. but a dead battery did.
I have a 2006 sc430 and have been having problems with the drivers memory seat although the passenger one works fine.
I have disconnected my batter for 5 minutes, moved the passenger seat all the way forward, heard the beep. Moved the reclining part all the way forward until I heard the beep, and the memory seat for the passenger works great.
I moved the drivers seat all the way forward, heard the beep. Moved the reclining part all the way forward until I heard the beep, but the memory seat won't beep (when you hold set and a number). I even replaced my drivers mirror (didn't tilt down due to bad motor), but that didn't work. Of course, I did redo disconnecting the battery and reconnecting it resetting both drivers seat and passenger seat.
The memory button for my electric seat is no longer working. The seats works fine, however I can't use the memory setting. [URL] .....
View 3 RepliesI have a 2002 SC430 and the seat memory buttons on both doors stopped working suddenly. No work done to the car, but I don't know what gives.
View 14 RepliesGot an interesting electrical issue on my 2004. I'm not sure if the issues are related but they happened at the same time. About a week ago the nav door stopped closing and the seat memory buttons stopped working. When you press the close button the nav screen moves back but the door never closes. The seat memory buttons on the door don't work either but the seat adjustment controls do work. When adjusting the seat position, as the seat moves moves, you hear beeping. It sounds like the same beep that you hear when memorizing a seat position. I checked and tested all the fuses they seem to be good.
View 7 RepliesI am tall 6'5" and was curious if is possible to move the seat rails back to create a bit more leg room.
View 3 RepliesMy wife and I both have our seating configuration programmer into memory seats 1 and 2). I notice, however, that in order to switch to the other person's setting, we have to hold down the 1 or 2 and keep it pressed while the seat adjusts itself. However, at some point the seat stops moving. If you then release the button and hold it again, the seat continues to adjust itself further. Is this a feature or is this a problem? I wouldn't expect that you have to keep holding multiple times in order to get the seat in it's final configuration.
View 18 RepliesTrying to lower the seat or seat rails in an SC430. I would like to get the seats down about an inch. Can the seats be taken out and distance between the bottle of the rail and the seat shortened somehow.
View 2 RepliesRemoving the back seat to allow the front seats to be reclined more? at 6'4'' I need more leg room! Or any other way on getting more leg room in the front seats?
View 1 RepliesI've noticed over the last few days that my seat position memory is gone. I thought maybe it was because i was using a different key, but that is not the case. I tried resetting buttons 1, 2, and 3, and neither set my seat to the position i specified. Button 1 is the only one that works, but it puts the seat all the way forward. Is my comfort module shot??? brand new car.
View 2 RepliesI have owned 2 SC and I notice both of the SC I have owned get a odd " hissing " sound, when the ignition is turned to the " On" position with the key located in the engine area, It will come on and then go off ...
Sometimes this " hissing " sound will come back on when driving and then off again ...
Hissing sound when the key is turned only to the "on" position?
I just got an 02 SC430 and I am going through a few things. The Nav screen works fine but is frozen in the rear tilt position. I would be okay if it were frozen all the way forward???
View 1 RepliesMy front drivers side pillar is flapping around and won't stay in the set position. It seems to be the washer that the one of the clips goes into (at the very bottom of the pillar) has corroded.
So firstly I am trying to take it off - but after reading the removal of windscreen instructions I see:
21. REMOVE FRONT BODY PILLAR OUTER RH
a) Remove the nut.
I can't see a nut and if it's under the pillar how do I access it?
And then
34: INSTALL FRONT BODY PILLAR OUTER RH
a) Exchange the clip with a new one
What clip is this referring to and what is the part number.
My 2002 SC430 is driven 2 -3 times week and has 30K on it. January '08 I replaced run-flats with high-end non-RF Michelins sugg'd here. Ever since, tires have lost pressure. So far, I was told front pass. rim (orig. factory chrome) had a crack, that was fixed, but tire still loses pressure. Rear Driver's tire supposedly punctured at 2 weeks & replaced..but still loses pressure. All tires & wheels were checked & rotated, now 2 still leak in new positions.
According to Dealership & Tire place familiar with SC430's, my Valve stems and sensors are fine (TPMS works fine), tires are good, rims aren't cracked, but tires go soft. Yesterday a Tire place that does only Lexus & Toyota just told me "invisible corrosion" on rims makes moisture collect where tires seal to rims and this causes slow leak!?