Replacing license plate bulb on a 3rd gen rx? I tried taking off the interior lining on the rear hatch but no luck. There's access covers for taillight & reverse, but none for license plate light. I also tried "popping" out the plate light cover right above the license plate... don't think they are designed to be popped out.
View 3 RepliesHow to change the license plate light bulb for lexus rx 350 2010.
View 4 RepliesNotice a rattle when they close their trunk?
My top screws are plenty tight, but the bottom portion seems to not be secure enough since they do not have screws.
I tried doing a search on how to replace the License plate LED bulbs...
Looking for pictures or instructions on how to replace them...
My Ultra white IS350 is 15 months old, and when I took out the screws to my license plate today, I noticed a little bit of rust on the mounts (where the screws would go into).
I believe this is a pretty common issue for all cars - essentially, the mount was sprayed with body paint, but the paint would be stripped when you put a screw in. It's just a matter of time before that happens.
I am just concerned it would rust through my trunk if I continue to leave it.
FYI: I already use stainless steel screws
I have an intermittent error that comes on most of the time I have my headlights on, but sometimes goes off and comes back while I am driving. It shows me the bulb out light, and says on the screen "Number plate Check license plate lighting!" I have never touched the oem factory bulbs on the license plates, and if i get out and look at the plate, both lights are on over the plate.
The only change I have made was about a year ago, I installed an LED bulb in the trunk, and ran a second OEM trunk light in the left side and installed an LED bulb in that too, tee'd off the factory trunk light housing. But like I said, that was 1 year and 30,000 miles ago, and my bulb our error for the license plate has only just started, so I doubt they are related.
After going through the car wash several times now in my 2010 RX 350, my front license plate has been bent in all different directions. Car wash guys say it's due to not having a full plate holder, where as 4 screws secure the plate vs. only the top 2 as we have. Any plate holder from another vehicle that I might adapt to overcome this?
View 14 Replies02 Camry, how to I remove the burnt license plate bulb? Took off the underside trunk carpet and disconnected bulb harness, but I don't know how to remove the plastic piece that holds the bulb in place. Does it pull out, or twist out? I don't want to break it!
View 1 RepliesI wanted to change my license plate bulbs to LED's. Can't figure out how to get to them. The book says have the dealer replace these bulbs if burnt out. I Always like to try to do things myself.
View 7 RepliesI have a 2010 RX450h and live in Minnesota where it is hard to hand wash my car. The darn car washes tend to catch the front of my license plate frame and bend it and the license. I have tried several different plate frames and none worked. Minnesota plates are now the thin, non-stamped plates so they are very flimsy.
I even tried putting a plastic plate behind the license to make it more rigid but that failed too.
how the chrome trim above the rear license plate is removed?
View 4 RepliesHow to change out 2015 RX350 headlight bulb? How to replace the bulb on the 2015 RX?
View 12 RepliesFor a few weeks now I noticed my stock license plate bulbs started to act strange. My left one is about half burned out, and the right one started to flicker and burned out entirely.
So.. Easy fix right? I bought 4-smd led lights to replace the burnt out ones and as soon as I installed them they worked perfectly! But about twenty minutes later .. The right one burned out. And the left one is dim.
Is there something wrong with the wire? what can I do?
How do I change my license plate bulbs in a 2010 ES350? I bought some 194 JDM Astar LEDs. I took off liner and changed backup bulbs but can't figure out how to change license plate bulbs.
View 4 RepliesI'm in the process of replacing license plate bulbs. I broke the old housing for one of the bulbs so I bought new LED lights on eBay and they came with the housing. The problem is, I can't get the cover to stay clipped in to the tailgate. How to get the lights to stay in? What am I doing wrong?
View 7 RepliesI'm trying to change my license plate bulbs to LED but cant figure out how get to the bulb. I've already removed the carpeted cover but cant seem to figure out how to get the bulb out..... 2007 ES350....
View 3 RepliesWhere the license plate lights get thir power from? I have a 2002 SC430 and the plug is just dangling. It goes behind the plate and then if I look under the car, it is just there by the bumper and I cannot find a connector that it can reach.
View 3 RepliesI try to install LEDS on it and I guess I accidently blew the fuse and when I try to search for it, I can't locate it.
View 3 Repliesyesterday I got the idea to move the plate bracket on the front all the way down so it gives it a much cleaner look and doesn't obstruct the grille. To do so test mount the bracket on the lowest position, then have someone hold it. Then you take a 1/8 drill bit and make the two new wholes then put everything back together.
View 8 RepliesI need to mount a plate on front bumper and there are dimples for 2 holes. Do I just use self tapping screws here as I've read you don't need a mounting frame?
View 3 RepliesHow do I change my license plate bulbs? I can't seem to get the plastic covers to pop off without worrying about breaking something. Even reading about people saying the puddle lights were hard to change, i did mines in 10 minutes in the dark with a small flashlight lol.
This was a lot easier old my old g37/350z ....