Lexus RX 2004-09 :: Ignition Switch Stuck / Occasionally Key Would Not Turn To Start
Dec 12, 2010
'04 RX330: Starting about a year ago, occasionally when inserting the ignition key it wouldn't turn to start. Take key out try again and it would start. Progressively, it seems to be requiring more and more in/out cycles to get the key to turn. It's like the transponder is not recognizing the key FOB. I have two keys, one is a master and other is a sub key, both have the problem. What has to be done to correct it? I'm afraid the dealer will just change some expensive ignition part when there's an easier fix.
View 14 Replies
Advertisement
I put my LS 430 key in my RX330 yesterday, I realized as soon as the ignition would not turn. I put the RX key in, and ignition will not turn. I'm assuming that the pins may be locked so I tried a few options.
- I wiggled the key.
- I lubricated the lock.
- I tried rocking the car while trying to turn the ignition.
- I tapped the ignition lightly with a screw driver and hammer, but no luck.
- I turn the steering wheel while turning ignition to make sure its not locked.
I really don't want to get the car towed to the stealer/dealer.
View 8 Replies
I'm trying to get friend's 04 F150 4x4 started. I think it might be the ignition switch. Here's what I've done. Turn the Key and nothing happens. Not even a clicking sound from the battery.
-verified the battery had a good charge and that terminals were clean, connections were tight.
-checked the fuses in the passenger side kick panel, none were blown
-Determined there was power to the primary Pos wire going to the starter , but no power being sent to the smaller wire that goes to solenoid at the starter.
-Hooked a jumper wire to the starter solenoid and engine did crank (so starter is good and battery is making good connection)
This is why I'm thinking its the ignition switch.
1) Where is the ignition switch located?
2)How can I test the ignition switch?
3)Could it be the "cylinder lock and keys" that is faulty?
View 5 Replies
My young lad just picked up a 2004 F150 4x4. While fixing it up we have encountered a weird problem. The key goes in , starts and runs the truck but cannot be removed, unless you unhook the battery.
View 5 Replies
I have recently been having problems getting the ignition switch to turn. There seems to be a negative correlation to warmer weather (the warmer the weather, the more likely I will have a negative experience --- and I will get the switch to turn only with some difficulty). When I have such a failure (in which the switch does not turn), I take the key out, wipe it off with my hand, flip it over and shove it back in. Sometimes this works with one try. Sometimes it takes multiple tries. My fear, of course, is that one of these times it will never work, and I will be stranded. I should add that I do have another key, and that I have had the same experience with this key. I don't really want to spend hundreds of dollars on a new ignition switch... and I especially don't if that is really not the problem.
View 2 Replies
After a morning of errands, my wife parked our 03 GX in the driveway. When I went out to start it, the ignition switch locked up. Would not budge! I finally had to have it towed to the dealer.
View 9 Replies
I mistakenly put the wrong lexus key in my 2004 RX ignition switch. It would not turn on the ignition. I then put in the right key and it also would not turn on. Is there a way to reset the ignition (hoping it is just a theft prevention), or do I need to replace the ignition switch??
View 13 Replies
Have a 2007 GX 470 with 70,000 Miles. Recently we have had problems with the ignition getting stuck. Key will go in, but, will not turn. Happens randomly and unpredictably. Will start after a period of time. Sometimes 30 minutes, sometimes several hours. My not happen for a few weeks or sometimes 2 or 3 times a week. Neither Lexus or Toyota claims to have heard of this problem.
View 14 Replies
My key got stuck in the ignition and I was unable to start it. The owners' manual shows a small hole to the left of the key slot which is poked with a paper clip to release the key. At some point the ignition in my tdi was replaced and no small hole is present. A knowledgeable tow truck operator/mechanic coaxed the key from the ignition and the tdi started when the key was returned to the ignition and turned. What is the proper way to remove a stuck key from an ignition without the little hole. I was reluctant to force it out. The ignition currently in my '04 tdi has a raised bar to the left of the key slot which I was unable to depress.
View 3 Replies
My wife recently purchase a 2013 Focus SE 5 door and a few times now the ignition key "sticks" in the switch and will not release. She has to turn it back on and off a couple times to get it to release.
View 1 Replies
None of my 4 keys will operate my ignition switch.
It's stuck in off position. Steering wheel is not locked and I have pulled pretty hard on it to see if I could get the ignition switch to turn.
I have a new switch on the way but I have to get the old one out and don't know how to get old one out if I cannot turn the switch to on position.
View 14 Replies
I have a Lexus RX 330 2006. Two days ago my key couldn't start the car he stuck inside the ignition. I ordered a locksmith guy and he open the auto meter so he can get to the ignition. Now the ignition working but when I try to start the car the car doesn't start. The security system turn on and off , it's seem like the car doesn't recognize the key, the guy also make a new key and program the car but still the car is not charging, I also order mechanics to see if somethings wrong with the car and he didn't see any problem . I think the car shut down and I need professional guy who know how to program the car...
View 4 Replies
Ok have a slight lack of information but ill explain this the best I can. Friend of mine has an 04 5.4 that occasionally wont start. turn the key and gets nothing. other times it will start right up. thinking this is either a starter or ignition switch issue just trying to verify before he drops what money he has to try and fix it. When the truck fails to start he says he hears a click from under the hood and that's it, but if he tries it several times occasionally it will finally turn over and start. I did try to search for this prior but found nothing so I think I'll just have him get the starter test and go from there.
View 3 Replies
So, I have an 89 Ford Ranger 4-wheel drive and the steering wheel is locked up (along with the ignition switch), neither of which will turn or budge. I've been told to shake steering wheel from side to side while trying to turn key--but after fifteen minutes of that (quite a workout) bupkis, nada, nothing. So, other than taking a sledge hammer to the whole truck? Is there a way to simply break loose the mechanism (I don't need the security aspect of the locking wheel/ignition, since I only use this for "farm use". But I really need it fixed.
View 9 Replies
120K miles - love the car
CEL, skid, VSC trac and VSC off lights on - dealer said the code was p2441 Secondary Air Injection System switch stuck. Dealer said I needed to replace air injection system and that the cel would not go off until it was repaired. They completed the 120K service and when I picked it up, all the warning lights were off. I have driven it a couple of hundred miles since then and still no lights. Does that mean it could have been something else???? I love the car, but I need tires and brakes and now repair charges for a 2005 car with 120K.
View 14 Replies
Had to replace the ignition switch. after I went to crank it after switching it out, there was a buzzing around the relay control module. Thought that maybe somehow the ignition tripped something in it so bought a new one. IT is still buzzing and car won't turn over. everything lights up on dash. tried to see if there were any codes and the scanner just reads "fail".
View 5 Replies
I was having all the tell tale signs of the almighty ignition switch. No lights, wipers, heater fan. But I didn't have time to change it. The other day went to start it and nothing. I changed the switch I have headlights wipers blower fan now which is sweet. But the car still wont turn over.
View 2 Replies
When I put my key in the ignition, I cannot turn the key. I tried putting a small amount of WD40 in the ignition and turning the wheel back and forth while trying to start, but all that did was make my key greasy and my wheel lock up. I've tried getting a new key made from Lowes and Home Depot, but their keys are too wide and will not fit in the keyholes. The only thing I am down to is replacing the ignition switch completely but I'd rather do that as a last resort because my car has had a big problem every week (alternator gone, new wheels, new master cylinder, new rotors/brakes). I haven't explored yet? And also, if it comes down to replacing the ignition switch, how would I do that without being able to turn the key?
View 2 Replies
I have a problem with turning my key. It will not turn at all. I have taken the upper and lower part of the cover off to expose the switch and removed one screw from the ignition housing, but the internal part of the ignition switch will not come out. How do I completely remove this ignition switch. I have already removed the negative battery cable. It seems this is a continual problem with focuses. Oh, do I need a releasing tool to release the ignition switch.
View 7 Replies
I have a 2000 Staturn LW2 auto, 6cyl. When I try to turn on the car, sometimes the engine does not turn, doesn't make a sound, nothing. When I move the steering wheel, it turns on fine, it has to be in a certain position. Does that mean, the ignition switch is faulty or is it the pin? Is there a test I can do?
View 7 Replies
I am having a little issue with the ignition in my car. I had the typical no headlights/wipers/heater etc. so I ordered up a new ignition switch and when I went to replace it, the switch fit perfectly and had the correct part number but when I put my key in to try and start the car I couldn't even turn the key but when I put the old switch back in it would turn just fine. Also when I removed the old switch I noticed the red wire going to the switch was slightly burnt right at the terminal.
Here is the basic procedure I did:
-Unhook negative battery cable
-remove lower dash/ center console
-remove switch
-install new switch
Whats this little metal piece? I did not see that when I did mine...
View 10 Replies
