Lexus RX 2004-09 :: Ignition Switch Is Locked / Would Not Turn
Nov 27, 2011
I put my LS 430 key in my RX330 yesterday, I realized as soon as the ignition would not turn. I put the RX key in, and ignition will not turn. I'm assuming that the pins may be locked so I tried a few options.
- I wiggled the key.
- I lubricated the lock.
- I tried rocking the car while trying to turn the ignition.
- I tapped the ignition lightly with a screw driver and hammer, but no luck.
- I turn the steering wheel while turning ignition to make sure its not locked.
I really don't want to get the car towed to the stealer/dealer.
View 8 Replies
Advertisement
After a morning of errands, my wife parked our 03 GX in the driveway. When I went out to start it, the ignition switch locked up. Would not budge! I finally had to have it towed to the dealer.
View 9 Replies
'04 RX330: Starting about a year ago, occasionally when inserting the ignition key it wouldn't turn to start. Take key out try again and it would start. Progressively, it seems to be requiring more and more in/out cycles to get the key to turn. It's like the transponder is not recognizing the key FOB. I have two keys, one is a master and other is a sub key, both have the problem. What has to be done to correct it? I'm afraid the dealer will just change some expensive ignition part when there's an easier fix.
View 14 Replies
I have recently been having problems getting the ignition switch to turn. There seems to be a negative correlation to warmer weather (the warmer the weather, the more likely I will have a negative experience --- and I will get the switch to turn only with some difficulty). When I have such a failure (in which the switch does not turn), I take the key out, wipe it off with my hand, flip it over and shove it back in. Sometimes this works with one try. Sometimes it takes multiple tries. My fear, of course, is that one of these times it will never work, and I will be stranded. I should add that I do have another key, and that I have had the same experience with this key. I don't really want to spend hundreds of dollars on a new ignition switch... and I especially don't if that is really not the problem.
View 2 Replies
I have a 2008 RX 350 and I am experiencing issues with turning the key ignition and having the steering wheel locked. It gets locked and after several attempts at jimmying the key it eventually starts. My concern is that if I keep this practice up I will damage my key. I have addressed this issue to the dealership and I was naive and trusted them with fixing the problem with my last maintenance visit. Thinking the the problem was solved I started to experience the same problem again. I was first told that it is possible the my key chains are too heavy which could of caused the problem but I lightened the load and still have this problem. I've read about this problem with other people but there doesn't seem to be a solution.
One thing I have noticed is that I tend to experience this problem during the cold weather. During warmer weathers I don't have issues with the key ignition being locked but now that it's cold I am having the problem again (not sure if this has to do with anything). Do I need to change a part out to fix this? I've also read that there can be dirt in the ignition which needs to be cleaned out. Will this work and if so how do I do clean it?
View 1 Replies
I'm trying to get friend's 04 F150 4x4 started. I think it might be the ignition switch. Here's what I've done. Turn the Key and nothing happens. Not even a clicking sound from the battery.
-verified the battery had a good charge and that terminals were clean, connections were tight.
-checked the fuses in the passenger side kick panel, none were blown
-Determined there was power to the primary Pos wire going to the starter , but no power being sent to the smaller wire that goes to solenoid at the starter.
-Hooked a jumper wire to the starter solenoid and engine did crank (so starter is good and battery is making good connection)
This is why I'm thinking its the ignition switch.
1) Where is the ignition switch located?
2)How can I test the ignition switch?
3)Could it be the "cylinder lock and keys" that is faulty?
View 5 Replies
I mistakenly put the wrong lexus key in my 2004 RX ignition switch. It would not turn on the ignition. I then put in the right key and it also would not turn on. Is there a way to reset the ignition (hoping it is just a theft prevention), or do I need to replace the ignition switch??
View 13 Replies
2001 Honda CRV. Key will not turn. Lights work, steering wheel is not locked up, clutch in but key will not respond.Interior light goes on when key removed. Key will simply not turn.
View 6 Replies
I've got a 2007 rx 350. The steering wheel is locked and the key wont turn. I've tried everything, forcing the steering wheel left and right, forcing the gear shifter to neutral and moving the car. I even tried to spray some wd-40 on the key and then trying it.
View 14 Replies
So this happened 2 times before, I am sure it is something I am doing and not the car.
So i just parked and turned off my car, and i noticed i left my windows up, so i tried to turn the car back on but the ignition would not turn and steering wheel would not move. I pressed harder and harder but it still was locked. My bro told me that same happened to his Civic and to unlock it you have to press on break hard and ignition would unlock, i tried that but nothing happened.
I googled and read online to insert the key into the ignition, try turning the car on and at the same time turn the wheel side to side. I did it and the car unlocked. My question is this, why did it lack in the first place, has this ever happened to you, if so how did you unlock it.
View 10 Replies
Had to replace the ignition switch. after I went to crank it after switching it out, there was a buzzing around the relay control module. Thought that maybe somehow the ignition tripped something in it so bought a new one. IT is still buzzing and car won't turn over. everything lights up on dash. tried to see if there were any codes and the scanner just reads "fail".
View 5 Replies
I was having all the tell tale signs of the almighty ignition switch. No lights, wipers, heater fan. But I didn't have time to change it. The other day went to start it and nothing. I changed the switch I have headlights wipers blower fan now which is sweet. But the car still wont turn over.
View 2 Replies
When I put my key in the ignition, I cannot turn the key. I tried putting a small amount of WD40 in the ignition and turning the wheel back and forth while trying to start, but all that did was make my key greasy and my wheel lock up. I've tried getting a new key made from Lowes and Home Depot, but their keys are too wide and will not fit in the keyholes. The only thing I am down to is replacing the ignition switch completely but I'd rather do that as a last resort because my car has had a big problem every week (alternator gone, new wheels, new master cylinder, new rotors/brakes). I haven't explored yet? And also, if it comes down to replacing the ignition switch, how would I do that without being able to turn the key?
View 2 Replies
I have a problem with turning my key. It will not turn at all. I have taken the upper and lower part of the cover off to expose the switch and removed one screw from the ignition housing, but the internal part of the ignition switch will not come out. How do I completely remove this ignition switch. I have already removed the negative battery cable. It seems this is a continual problem with focuses. Oh, do I need a releasing tool to release the ignition switch.
View 7 Replies
I have a 2000 Staturn LW2 auto, 6cyl. When I try to turn on the car, sometimes the engine does not turn, doesn't make a sound, nothing. When I move the steering wheel, it turns on fine, it has to be in a certain position. Does that mean, the ignition switch is faulty or is it the pin? Is there a test I can do?
View 7 Replies
I am having a little issue with the ignition in my car. I had the typical no headlights/wipers/heater etc. so I ordered up a new ignition switch and when I went to replace it, the switch fit perfectly and had the correct part number but when I put my key in to try and start the car I couldn't even turn the key but when I put the old switch back in it would turn just fine. Also when I removed the old switch I noticed the red wire going to the switch was slightly burnt right at the terminal.
Here is the basic procedure I did:
-Unhook negative battery cable
-remove lower dash/ center console
-remove switch
-install new switch
Whats this little metal piece? I did not see that when I did mine...
View 10 Replies
I'm having a problem with my ignition switch. It won't turn and I have to turn the steering wheel for it to finally work.
View 4 Replies
97 Toyota Camry 2.2l motor.
Sometimes, when I turn the ignition on I don't hear a sound and all the power dies in the car (the radio ejects the CD and all the presets are erased when I turn it out of start). This can happen once or twice in a row then generally the car starts up normally.
The battery is brand new (1 month) and is fully charged. My hope is that it's the starter drawing too much power when it tries to start? It's entirely possible it has the factory starter still on the car.
View 8 Replies
In the mornings when I turn the ignition switch to on right before starting, I don't hear the fuel pump wining. I notice the wining on almost every other car that Ive drove. I don't know if its because of this I get a rough start. It usually happens only in the mornings especially on cold days. During the rest of the day I can hear it clear and it turns on right away with no problem. I have tried to turn the ignition switch on then off then back on to see if the pump would turn on but nothing. Also sometimes I have to keep the gas pedal down about half ways for it to turn on and not stall. Tomorrow I am going to check to see if any fuel lines are clogged.
Car is a 2000 accent gs 1.5l 12sohc ... With about 87500 miles on it ...
Anything I should replace with these many miles ... Planning to replace spark plugs and timing belt myself ...
View 1 Replies
My 2004 Accent is stuck in the "lock" position in the ignition, and the wheel is locked and barely turns in either direction. I know this is supposed to be an anti-theft feature and I've tried all of the solutions listed here...
Turning the wheel hard and soft in either direction while holding the brake all the way down and trying to turn the key. Putting the car in neutral and then park and trying the above Disconnecting the battery for a few minutes and trying the above Jacking the car up on one side to release the tension on the pin.
My question is can I remove the spring at the bottom of the locking pin by drilling a hole in the center of the plate? I've seen a few youtube videos of this done on BMW's. It will cost me $500 minimum to replace the ignition or steering column based on quotes I got.
View 10 Replies
I am trying to install the Red TRD ignition switch push start button. I have already removed all the panels I need according to the Toyota instructions. I have two questions;
1.) How do I disconnect the knee airbag ? I was trying to remove the connector but was not sure on how to remove it. The instructions just says be careful.
2.) How do I get the ignition switch out ? There is barely any space to put your hand underneath the dash to remove the two back clips. (after removing all the necessary panels) Since I can not disconnect the knee airbag , It's hard to lay down and look under the dash.
View 1 Replies
