Just picked up a used 2009 RX350 and noticed the low beam light output is terrible. Very difficult to see, especially when turning corners. Also have a bit of fogging of the headlight assembly covers which I assume can be cleaned up. What is the easiest way to increase light output?
View 14 RepliesNew owner of a GX 460. Noticed that when driving in the parking garage and turning around the corners, the wheels make screeching noise. the GX 460 is not a very big SUV but it feels like i'm driving a huge truck when trying to turn.
And also need confirmation that during normal driving, the central differential should be disconnected, which means a yellow icon showing on the dial, i.e., a yellow icon that shows a cross in between the four wheels.
I have started to notice a crunching sound seams to be coming up thru the front wheels only when turning tight corners this seams to be related to outside wear to both front tyres.....
View 7 RepliesWhen I turn over bumps not on corners I hear nothing lol ..I just changed the tie rods for other reasons and nothing is loose in the front end now..But this sound is from the box of the truck like something is in the box bumping around when turning corners over bumps..Its frustrating and I cant find out what it is..Only happens when turning over bumps ?
View 6 Repliesfor the past few weeks when turning corners the outer rear tyre is skipping as if the diff is locked. was thinking of taking it into the mechanincs and maybe replacing it, but now the problem has gone no skipping when turning. could this be an electrical problem mayb a sensor?
View 8 RepliesI have an '07 ES350 with the factory HID headlights. The driver side headlight will start to flicker a few minutes after being turned on and then eventually turn off. Turning the headlights switch off and then back on will turn this headlight back on but it will start to flicker again after a few minutes.
I had this problem last year with the same headlight and took it to the dealer who replaced the HID bulb but now it's back again. I've also noticed it seems to occur during the cold winter months and not so much during warmer weather.
The passenger side HID works fine with no problems. Perhaps it's a loose wiring connection but I'm not sure if this is something that can be checked without taking the entire HID assembly apart.
So car not turning over after replacing (right side) headlight assembly. Was turning over prior. Replaced the battery, same result.
View 4 RepliesA couple weeks ago I noticed the passenger side headlight would turn off almost immediately after I turned it on. After a couple hours of swearing at it/trying to twist it out, I finally pull the bulb and socket out of the metal retaining clips in one piece. I had to use a couple channel locks to get the bulb to twist out of the socket, and when I finally did I saw the socket and bulb were very toasty.
I cleaned up the socket, replaced both bulbs, and everything seems to be working fine so far, knock on wood. Any example of this kind of arcing between the bulb/socket? If this is a one-time thing, great, but I'm wondering if it's symptomatic or problems someplace else.
I traded in my 2015 for a 2016. I had the hesitation in my 2015 when moderately accelerating out of corners. So far in the last 1000 miles on my 2016, no hesitation.
View 2 RepliesI have a 2009 GS 350 AWD and this is my first issue I have had with my sunroof. It was raining this morning and we noticed that both rear corners of the sunroof have a steady drip leak. I opened and closed the glass as I figured it was a positioning issue but the leaks remain. I know there are drains but my guess is that the drains will not work fast enough for the water to drain (there is no other leaking and it is not leaking into the headliner yet).
View 2 Replies120K (64 by me & 56 by prior owner during first 6 1/2 yrs) I was having a groaning noise when going around corners especially when headed down hill and hitting the brakes at the same time. I also had a rattle or popping going over bumps. I couldn't isolate the noise and nothing felt loose in the front end when I jacked it up. The dealer said the lower control arm bushings and ball joints needed to be replaced for $1545. I asked about front struts and was told that the control arm bushing and ball joints had to be replaced first before the struts could be examined.
I replaced the control arm assemblies (had to lower front cross member while supporting engine w/large jack and removing lower engine dog bone), ball joints, stabilizer bars and stabilizer bushings myself. Ball joints required removing axles and steering knuckle assembly to remove metal CV dust shield on back side of steering knuckle. (will post procedure later). Had lined up and the noise changed (groaning on corners left and rattle became pronounced on all bumps like the front end was about to fall out). By the way no cracks or excessive wear on any of the rubber components as I have always seen on the Subaru and other cars I had.
I am replacing the rear passenger hub assembly and as soon as i put a significant amount of torque to the axle nut...i get a crazy grinding noise and the hub becomes very difficult to turn. When I disassembled the old assembly it took very little effort to push the axle freely in the splines of the hub after i took the 32mm nut off. Now when i start to get the grinding, i remove the axle nut and it take some serious whacks with a larger hammer and brass drift to free the axle spline in the hub.
Ive dug around online and found someone that had to slip a couple pieces of wood in between the sheet metal dust shield and the end of the axle to fully seat it.
My headlights suffered from the dreaded condensation problem. I brought them to Lexus after getting the warranty enhancement paperwork and had them replaced. Shortly after the passenger side wheel cover was ripped off after getting caught on some ice during a storm. It was very shortly after that that condensation begin appearing in my passenger side headlight.
At that point I was unaware that the wheel well cover had been ripped off. I brought it back to Lexus to have it looked at since I only had the headlight replaced a few weeks before. I was told it would be at a cost of $2,500 to replace with an additional $400 for the wheel well cover. Needless to say, I did not have the work done that day. While I was waiting them for them to finish the paperwork I bought the wheel well cover for $50 online but since then I've had difficulty locating the headlight.
I brought it to my mechanic and he was unable to find the headlight as well. I have a 2009 rx350 with HID AFS headlights. I have looked on ebay, Amazon and just through the internet to see what I could find but I'm finding only halogen headlights. Most of what I'm seeing on eBay are for non-adaptive lights that are damaged.
My other D1S headlight bulb was fainting but didn't got chance to replace it until it went off totally. After replacement everything worked normally but after about one week, the replaced bulb does not lit up every-time. I needed to switch light on and off few times to make it work.
And to be more suspicious, now the other bulb has done to same... haven't lit up always.And couple of times they did it same time, I didn't have headlights in darkness at all. Just bad contacts to bulb or first symptoms of ballasts going to an end? What solution you can use there to clean contact surface not to mess the light housing?
I have a 05 lexus rx330, i bought it in december 2014. And the dealership replace the left headlight assembly because the headlight was foggy and watery and it wasnt turning on. And now 5 months later, the light is on and flickering, and later after 10 seconds it turn off.
View 3 RepliesOne of my headlight is burned out and I would like to replace. I don't want to go with OEM. Looking something better and brighter. 2008 GX....
View 1 RepliesMy driver side headlight is dull compared to 2yr old one on the pass side. Where can I get an aftermarket HID one. I don't want to restore it...
View 4 RepliesMy driver side lower beam (projector) will go out after a couple minutes when its turned on. If I flip the switch to off and then on, it turns back on again. Is this a sign of it going out? I am assuming i have the HID version.
View 9 RepliesRecently my 05 RX330 had the driver side low beam bulb go out. I took it to a few places and they said take it to the dealership as they have special tools to change it. Of course I took it there and they were ready to charge me an arm and a leg to get 1 little bulb replaced. My question is do you have recommendations as to what I should do to get this fixed and not have my wallet get destroyed?
View 8 RepliesI went to check out a TDI. Got there and it had to be jumped (45F) The glow plug harness was bad. but even after we got it started and drove it for several miles to get it to operating temp, it was still difficult to start after shutting it off. Shouldn't it start up easily after being warmed up even if the glow plug harness was bad?
View 10 RepliesMy 2004 Explorer XLT 4.6L V8 AT is very difficult to shift out of park. Sometimes I have to push very hard on the brake in order to get the transmission selector out of park. Other times it is no problem.
View 1 Replies