Lexus RX 2004-09 :: 2009 RX Low Pressure Port Location
Jul 22, 2015
Where is it. Probably under some shroud, but before I start taking things off, where it is from the perspective of standing in front of the grill.
View 2 RepliesWhere is it. Probably under some shroud, but before I start taking things off, where it is from the perspective of standing in front of the grill.
View 2 RepliesRecharging the A/C on a 2006 Hyundai Sonata GLS.
I think I have a slow leak, so I bought a DIY and was going to recharge it and see if that fixes it. Where exactly is the low pressure port so I can charge it?
Is it complicated to do? Looking for a picture of the location?
Looking for the low pressure switch, (back towards fire wall, black cap on it passenger side) I think I found it, but when I hook up the AC pro that gauge doesn't register any psi, when I hooked up same AC pro to our Acura TL the gauge registered and I was a little down so I added some In.
So any tips on what's up? Wife's car blows cold air just wanted to see where it's at and if I need to check for leaks or just add some 134a ...
I have a ES350 and it is doing the issue of having warm air (or not cooled air) on the driver side, but has cold air on the passenger side. I looked around and saw it was a common problem. One of the solutions I read was to just refill the system with R134A. Not a problem for me, except I don't know where the low pressure port is located in my car. I was trying to find a online service repair manual on my car to locate where I need to connect to, to recharge the system.
View 12 RepliesWhere the oil pressure sensor is located on a 2013 F150 with the V8 is located?
View 3 RepliesWhere is the OBD2 port?
View 1 RepliesWhere the low side air conditioning port on a 1988 ford 460 is? I found the high side one. But not the low one in order to charge the system ..
View 5 RepliesDoes the 2008 rx model have a usb connection/port? My mother recently purchased a 2011 and they have a great usb port in the middle console. I didnt see one on my 2008 (with navigation).
View 4 RepliesI guess I shouldn't be surprised that I can't find the location of the OBD port in any of the written material on my '06 Avalon.
View 3 RepliesI have a 1994 Porsche 968 and I can not find the lowside AC charge port. Where it is?
View 3 RepliesI just learned that the charging port is in the right rear, compared to the Prototype with the port in the left front. Seems to me that about 50% of the time, the driver will get in the car and drive off with the car still plugged in because they won't see the cable when getting in. Or at best, you will get in the car, and then have to get out again to unplug it. What am I missing?
View 19 RepliesAs luck would have it I'm leaving out in the morn for 600 miles , Noticed a nail in my L/F tire yesterday went too Goodyear they pilled the tire patched it inside.. Then this morn went to fuel up my ABS light stayed on .. Did this last yr. went off after a few days but since the tire was pulled maybe its a bad connection ??? ..Jut want to be sure and scan codes
I want to scan it now to check and reset any codes But looked under the Drivers side dash can not find the OBD connection port looked on Passenger side nothing there either.. Looked under hood around fuse box did not see anything that kind of looked like a port with a cap I'd assume they cap them if under the hood .. Its a 05 S/D 6.0 locate this OBD11 port
To install my FLIR system I need a 12V power supply, ideally switched with my Gen III's ignition switch. Where in the engine compartment can I find that?
View 3 RepliesWhere the oil pressure sending unit is located? And could that be the cause of your low oil pressure when you still have almost full oil on dip stick?
View 6 RepliesMy son has an 01 LeSabre Custom with 87k. He says the a/c isn't working. I tried to put my gauges on it tonight, but I couldn't find the low pressure service port, but there's two on the high side (one on either side of a tubing connector).
I figure it should be obvious. I'm worried that the system was previously dorked with...with the two high-side ports and no low-side port. But everything looks factory.
The dryer is in the front left (passenger) of the engine compartment (when standing in front of and facing vehicle). I see the low-side line from evaporator come into it, then out of it down to the compressor in the center bottom, behind radiator. No port that I can find.
While looking for the a/c port, I also saw CVJ grease splattered all over on the driver side...it's always something. Just bought this last February (couldn't check the a/c too well) to replace the very nice 00 LeSabre 55k we bought in November for him. But the 00 didn't survive the collision with the truck that pulled in front of him...
I recently tried to recharge my 1994 Saturn SW2 air conditioning. The system took the charge fine, nice cool air again. Yea! On disconnecting the adapter, I heard the sound of escaping gas. I was able to place my thumb over the port and block the leak, tried reattaching adapter and removing several times, but the valve will not fully seal. Placing the cap back on the port with a small piece of plastic food wrap (hi tech) stopped the sound, but obviously not the leak entirely. A couple of weeks and the a/c is back to blowing hot air.
Is there any way to encourage the valve to seal? Should I try the variety of refrigerant that seals leaks? Is there a better choice for blocking the leak than food wrap? If it comes to it, replacing the low pressure line, is that something a person who knows how to use a wrench but not much more can do?
Have an E150 van with 302 engine. Where is the low pressure charging port on this beast.? The high press. is immediately visible but can not find low....
The van still has the old r-12 and I have 2 cans left...want to charge the system one more time before we get our new 6.0L VAN late this winter!
Plugging a multiple USB port into the single USB port? Does it work? For example a plugging a USB drive and an IPod?
View 4 RepliesI am doing heads studs and gaskets on the truck. I forgot to remove the stand pipe and started to lift the head off the truck with the engine jack. Well i bent the stand pipe and the port to the bock was a little loose. Tightened it back down and it seems ok. Could I have damaged anything by doing that? how is that all connected to the high pressure oil pump? I just want to make sure i didnt damage anything by doing that and since im already here I would rather make a fix instead of needed to tear down again.
View 5 RepliesI cant find the port on fuel rail to get a fuel pressure reading.it is nothing like my tarus.saw astem sticking up on front right of rail but it has some kind of covering over it. It is a 2005 freestar with the 3.9 motor.
View 5 RepliesMy trailer has surge brakes so I need to tap into the reverse light circuit to convert the 4 wire trailer harness to 5 wire. The reverse light wiring runs in the lower cargo area anywhere...trying to avoid having to trace it from the hatch into the headliner.
View 11 Replies