Lexus IS 2014+ :: Metal Rotating Sound Coming From Front Right Wheel
Jan 13, 2016
I have encountered a strange noise from my car. The sound is similar to a metal rotating sound. It may be coming from the front right wheel.
I cannot hear it on the freeway. I would say that I can hear it quite frequently at slower speeds. Sometimes It would go away momentarily.
I tried turning the wheel left to right to see if that had an effect at slower/higher speeds, doesn't seem related, could be wrong. Currently I am thinking it could be my wheel bearing...
View 13 Replies
Advertisement
4000 miles on my CW Golf R - zero problems until this morning. WILD, Loud sqealing, screeching metal on metal or maybe stone on metal sound coming from front passenger wheel. at first i was positive it was a pebble caught b/t the inside rotor and heat shield - i took the tire off and nothing there.. Also only really does it when I turn RIGHT.
View 13 Replies
The last couple of days I've noticed a metal clinking noise coming from the right front wheel area when I go over bumps. The best way I can describe it is what it sounds like when there's a loose washer and nut on a bolt. A metal on metal sort of thing. Tonight I was able to replicate the sound I heard by pounding on the tire and got it on video and posted it below. Watch in HD to hear the sound I'm referencing clearly.
[URL] .....
A couple of things to consider:
1. Just had spacers installed a few days ago
2. Also diagnosed the "clicking brake while turning slowly" issue. Thread about it here: [URL] .... Wondering if this has anything to do with the noise.
I have an appointment with Lexus tomorrow morning to have the brake clicking fixed under the TSB and several other issues addressed. Mostly rattles...
View 2 Replies
When driving in my parking garage, I can hear a slight metal on metal noise. An extreme example would be sharpening a knife on a sharpener, its not as loud or predominate.
-I've checked the lugs, they are secure.
Car has springs and spacers.
View 3 Replies
I have 1999 F350 7.3 Crew Cab 4WD. I took it on a 4 hours trip towing a trailer to haul a small tractor on it. after 3 hours of driving, I started hearing grinding and metal chewing sound coming from the front axle or close the wheel hubs. It was awful, terrible, ... you name it!!! I had to continue or I will lose the tractor I paid for already. The sound was coming for 1-2 seconds each 500 feet or so. It never stopped or changed. I pulled over to see what's going on and found the following:
1. Left shock is leaking badly
2. Right locking hub is gone (not sure if the truck had one before). I bought this truck last year, but I never had to use 4x4 and I know the 4x4 motor by the transfer case is missing and the nipple on the transfer case is set to the 2wd position so the front drive-shaft does not turn.
I took the front shock off and continued to drive without it, the noise did not go away.
I pulled over again and this time I noticed that the dust cover on each end of the front axle is missing too. I have never worked on these axles before, but I jacked one side, and sure enough, gear oil was leaking from the other side. I took the plug off the front differential and stuck my finger in it. I felt a creamy brown-greenish stuff in the differential. The consistency is like mayonnaise or thin peanut butter. I put the plug back on and went to pick up the tractor because I did not want to miss it fooling around with the truck on the highway.
The truck made it there and back (almost 5 hours total after the break down). The sound never stopped every 500 to 1000 ft.
After getting home safely, I took the other locking hub off, and took it for a test drive. I did not hear the noise, but now my right brakes are locking.
I took of the wheels and saw that the retaining snap ring (C clip) for the front axle on the right side came off by hand. I took the washers behind it off. Took the calipers and brackets off. I have never done front axle rebuild. I am not sure what has been damaged and what's still good.
Right of the bat, I know, at least, I need 2 shocks, one brake caliper and pads.
My questions are:
1. Is it possible to take the front axles off on both sides and make it 2wd for now until I have the money to rebuild the axle?
2. Could I use the same hubs? or they are most likely damaged and how to tell?
3. How to tell if the differential is damaged/needs rebuilding?
4. How to tell if the axles/spindles are damaged?
5. Is there a step by step tutorial to rebuild the axle with all seals, bearings, ...etc? How hard is the job for a hobbyist? I do most of my repairs myself, and I was lucky at 36 years old, I never had to rebuild a differential.
6. What else I might have damaged in the process of driving it that long with the noise? How do I tell if I did?
View 8 Replies
You can hear the clunky, groaning noise around 8 and 11 seconds when I turn the steering wheel, making a tight u-turn in an alley way.
What can it be..? I hope it has something to do with my tires since I'm getting new ones today. The current ones are pretty bald.
Quick video clip of noise...
View 7 Replies
When I was reversing back and turning the steering wheel. I heard a metal clunk sound and it had happened twice in the past two days. Today happened after I released the parking brake and set it to reverse. What is the problem? Miles on the car is ~30700 miles.
View 2 Replies
Sometimes when driving I hear a light squeaking sound coming from the front wheel area. When i drive slow, it is a slow squeak, and when I go fast, the squeaking speeds up. I am thinking about spraying some wd-40 or silicone lubricant behind the wheel to lubricate the area to see if it solves my problem. I will be sure not to get any near the brake area but my question is, does spray wd-40 under the chassis or around the control arm area to stop those annoying squeaking sounds?
View 6 Replies
I have a 2007 hyundai sonata, this car is my daily driver. I put 180 miles on it a day around trip. Currently has 180,200 miles on it. Last Friday on my trip home when i turned right I heard a metal on metal sound. I slowed down went straight and it went away. Talked to a few people and I think it may be the wheel bearing. Even if I hit a road reflector it starts up. It's the front left wheel. Get on the breaks it goes away.
So my question is... Wheel bearing??? And can I replace the whole hub and fix the problem or do I have to try and press the bearing out?
View 1 Replies
I replace my brake pads and rotors in the fall of 2015 with EBC parts. Now almost 13,000 miles later, I started hearing grinding and metal-on-metal contact in the front. So I went out and got PowerStop pads to replace the EBC (EBC had way too much brake dust). I took off the front wheels and noticed that the DF pads had about 1/32 left on them, ok I guess its time to change them out. Onto the PF pads, I find that there is almost no material left, in fact I could scrap off what was left of the material. I decided to do a rotation while I am at it and noticed that the rear brake pads on both sides look like I never used them!! Is it really that possible to have 2 stuck calipers, both on the rear at the same time?
View 2 Replies
I have a question about my C Four with 16" wheels. When the steering wheel goes all the way to a stop there is a thunk that feels like metal on metal. It is like there is no rubber bump stops. If this is normal. I am used to cars that have a nice cushioned bump at the steering limits.
View 1 Replies
I have a loose, binding, metal on metal sound on my steering wheel shaft. I have removed the steering wheel, replaced the clockspring, because when I removed wheel clockspring was in pieces and I thought that might be the issue. Guess not, because I'm still having problem. Other than having to remove or replace the whole steering column...
View 2 Replies
Honda Accord 2005 ... Just bought a new used car. All seems ok, but I have two problems.
(1) when not moving, i have slop in the steering and I can hear metal on metal contact when I turn the steering wheel. I pulled the tire and with basically no force I can move the rotor back and forth by hand. what it is and how to fix it?
(2) when braking, it appears that the front left pad sticks. Pads are not excessively worn down. Can't figure out how to get to the caliper pins ( thought they might be sticking).
Could the two be related?
View 2 Replies
I have a 2011 Camry and I have noticed that there is always a rotating sound coming from the front wheels. The frequency increase as I speed up and decreases as I speed down. I don't think it is the bearing since it always comes, not while turning or changing lanes.
I have attached a video. You can listen to it. The noise starts at 00:27 mark. It is very noticeable around the 1:10 mark. Sounds like something is rubbing against the wheel. Not sure what can cause this sound.
YouTube .....
View 3 Replies
I have developed a sounds that sounds like metal on metal. Not a grinding but more of a "swish swish swish" light metal rubbing when the truck has been running a mile or two. I can barely hear it over the radio but its very noticeable when the window is down. It is not affected by the pressing the brakes and it gets louder and faster in direct portion to speed. It will occasionally leave and start right back up. I touched the front rim around the hub and it was hotter than I wanted to hold onto. It didn't burn but it was hot. It was 105 degrees that day. Here is what I have done.
I replaced that front hub in 2010 and probably have 50K miles on it. I did the 3-9 test and there was no noticeable play. I spun the hub and while it seems to spin ok it does seem a little dry.... I will pull it tomorrow and see what it looks like.
I pulled the calipers off and the brakes pads are at half way and there is no burnt smell. I spun the rotor and it seemed flat and straight. I do have a small tiny lip all the way around them on both sides but I figured that's normal with 265K. I pulled the pins and they were dry but they didn't seem to be sticking. I cleaned them up with the boots and am going to replace them when I get some brake grease tomorrow. I have not looked real hard at the caliper but I plan on pressing that with a C-Clamp tomorrow to check it. Since the rotors and pads looked OK, I assumed there was not a stuck caliper although haven't ruled it out. The axle behind the hub seem to spin freely before I removed all this stuff and the hubs are not locked.
I think I covered it all .. I also thought it could be a rock or stick but nothing came out of my caliper or rotor when I took them off ..
View 14 Replies
I have an 03 Exp 4x4 Limited with 4.6L V8 with 167K on the clock. I'm getting a kind of humming rotating sound out of the front end when moving. The frequency definitely goes with the wheel rotation speed and the noise is the same with the trans engaged and when coasting in neutral. The noise is present at all speeds but becomes more of a humming sound as the speed increases at highway speed.
I've had both front wheel bearing hubs replaced (they were completely shot), brake pads and rotors replaced, and just had new tires. The rotating sound is still there though. What else is there that could be the cause? Is there another set of bearings somewhere in the front end?
View 11 Replies
I'm hearing a sort of faint rotating squeaking noise coming from the front of the engine; I can only assume that it's something with the belts. Nothing too pronounce cause I just notice it yesterday, anyway I was hoping I get another take on what this might be before I take it to the mechanic tomorrow.
View 12 Replies
Two weeks ago I pick up our 08 460 SWB , with 24,300 miles on the car ...
I noticed today while in park standing and waiting for my wife to come out the nail Solon ..the car had this very mild tremble / shake ...and sounded like a belt under the hood was loose .. Something like a rotating fan sound loud but not that loud to make a big stink out of... When I drove off and came to a stop sign I pressed the breaks and RPM's went from 1,100 to 1,300 and back down when the car was at full stop??
View 2 Replies
I have noticed recently that I have a "rubbing" noise and vibration coming from the right front wheel on my FX4. It is most noticeable from 5-10 MPH, and more pronounced when turning right. it is not constant. It sounds almost like a brake pad rubbing on a badly warped, wet rotor. It goes away when I apply the brakes. I am thinking bearing or possible CV joint.
The dealer can't get it in until Tuesday, and they say I will have to pay the deductible on the ESP, even if it is related to the steering vibration they could not replicate or fix about a month ago. I am seriously considering going to another dealer for my service. Given, they did absorb the deductible last time, but they didn't fix the problem!
View 14 Replies
I bought my R from Carmax about a month ago with about 26K miles on it (and, needless to say, I am in love with the car). However, after a week or two of driving, I noticed a squeaking/rattling sound coming from the front driver's side wheel well area when I let off the brake. It is loud enough for me to hear it with the windows rolled up, and it continues for several seconds at least after I let off the brake (maybe longer, but I can't hear it over the exhaust).
The rattle sort of sounds like it may have something to do with the turning of the wheel, so I thought it might be related to caliper vibration or something (not that I really have any clue. At all.). Anyhow, I took my R to Carmax to have them look at it because it is still under the 30 day warranty, and I figured I would start there before taking it to the local VW dealership. I got a call a few minutes ago from the service guy, who said the following:
"Our technician took a look at your car and determined that the sound is coming from your suspension. However, it is a normal sound and there isn't anything that needs to be fixed."
I argued with him and said that the noise may or may not be immediately harmful to my car, but it is certainly not NORMAL, and something needs to be tightened, lubricated, or replaced. He said he would have his tech look at it again.
View 5 Replies
A little less than a month ago my wife's old 1999 Mustang had the tires replaced. Since that time there she has noticed two new sounds:The first is whirling/grinding sound coming from the front right wheel that comes and goes. The second is a low, loud groan that seems to come from the front of the vehicle when the brakes are applied. The groan varies in intensity but seems to always be present when the brakes are applied. The groan is not unfamiliar to anyone that's driven an older car, but it is much louder than I have ever seen on any other car (on the other hand I usually drive a Corolla so it may be normal on a V6 Mustang ).
The first sound seems to have been reduced but not eliminated since I followed the advice in this video below and pushed the plate behind the wheel back a bit with a screwdriver. Now it is only audible when the engine is off and the wheel is spun (in other words, when it is sitting on a jack and the wheel is spun by hand), but it is still there.
I took it into the shop where the tires were purchased and mounted. The good people at the shop did rotate and balance them, but both noises remain.
I looked at the calipers and discs and everything seems in order except (possibly) two things. The discs have rust around the edges not unlike the ones in this photo below and I have no clue if that is normal or a problem. The rust is present on all wheels and only the one makes that noise, so I think that may not be the source of the sound,. On the calipers some substance (paint?) is peeling off, but otherwise they look fine and again the same is true on all the wheels so it seems that is unrelated to the noise. I have not been able to get a look at the pad, so I don't know what condition they are in.
Other information: The serpentine belt was replaced a few days after the new tires were installed. The radiator was flushed at the same as the belt was changed. They also threw in an oil change and all the fluids checked at the same time. The tires are new Michelin Defender size 205 /65 R15 and all 4 tires are new. The engine is a V6 and the transmission is automatic.
[URL] .....
View 2 Replies
