Lexus GX 2010+ :: Front Differential Leaking From Drive Shaft Output
Jun 13, 2015
My front diff appears to be leaking from the drive shaft output. it's not enough to leave drips but the skid plates are oily. Having the dealer look next week. 60k on a 2011 460.
View 3 Replies
Advertisement
I have a slight leak at the front differential and drive shaft. It is nothing major and I don't even notice a oil slick under the truck when it sits for a longer period of time.
View 7 Replies
I recently changed my sway bar bushings when I jacked the car I notice oil is leaking because the shaft is all wet. My question is it an easy Job or will it cost and is it something that's hurtful to the car if I don't fix asap...
View 1 Replies
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 Replies
I was getting ready to replace the carrier bearing and noticed the rear pinion seal is leaking. Before attempting the replacement myself, I would like some opinions on the noise in the video below. Is this normal? I am confidant I can replace the carrier bearing and pinion seal, but not sure I have the tools for anything else.
YouTube ...
View 4 Replies
My front differential is leaking. Are there any special Ford tools required to replace the seal? Or is it simply bolt (and fluid) removal, seal replacement, fill with new fluid. Any tips or heads-up on this?
View 2 Replies
2001 Jimmy 4wd, 115,000 miles; Recently I noticed a strong vibration when in 4WD, no vibration in 2wd. I found that the rear joint (at the transfer case) of the front drive shaft has play in it. I am assuming that this is the problem. It has the appearance of a CV joint. Is that joint rebuildable or do I need to replace the shaft?
View 1 Replies
My 1994 Chevy Suburban will not engage the front drive shaft. It has an electric actuator and it will not engage. the transfer case engages but not the front axal. When I shift the transfer case into 4Hi or 4Low it will shift itself but the light will not turn on. I have heared rumors that you might have to manualy connect it to the battery and have a kill switch in the cab. What is the problem and should I connect it manualy?
View 6 Replies
I am wanting to remove my front drive shaft from my 2004 Aviator for a couple of month's while I save money to have my transfer case replaced. Are there any safety concerns with this? just need a couple of month's to get the money together....
View 5 Replies
I am doing some work on the truck and need to get the front drive shaft to drop down, I have the four bolts out but I can not get it to move. What am I not doing?
View 3 Replies
I am on the fence with getting rid of my 7.3. Here's why. Whenever I crawl underneath the truck or look under the hood I see all these different oil/fluid leaks. She has less than 200k miles and I use her to tow my boat to go fishing.
Right now I am trying to weigh if the truck is worth keeping or selling and then getting a new/newer truck.
Here are some leaks. One is obviously oil and coming from what I guess is the front main seal. I really don't know. The other leaks going onto the U-joint look like oil leaking down the axle from the front differential.
I'm growing a business and not sure if I have time to play mechanic. However, everyone I talk to always exclaims, "You got a 7.3?! You luck SOB!" and I am kinda getting the feeling letting her go would be a mistake. FWIW, she is paid off.
Other than a slight wobble in the steering wheel at speed, she runs like a hoss.
View 1 Replies
My t case will engage in 4 high and 4 low. so i know the switch and motor works because it go all the way to 4 low and i can feel the lower gears. BUT the front drive shaft is not turning because i know that the front diff is engaging just fine cus one I just fixed it and because when i put it in 4x4 the front drive shaft is locked in but when i take it out the drive shaft moves freely when i turn it by hand. But when I test it in gravel or mud the front wheels still ain't turning. So its gota be the t case. But what are the part that may be broken in the t case and if I can fix it wile its still on the truck.
View 4 Replies
I installed a JDM 2ZZ-GE engine and 6 speed manual trans-axle into my 2000 Celica GT.
I have ran into a interesting problem. I replaced the output shaft seals and now whenever the car is in the air and the suspension is unloaded (the drive axle is pulled slightly from the trans) the drivers side seal leaks a bit of gear oil. The drive axle is snapped into place. Nothing leaks when the car is on the ground.
I did reuse the old drive axles, which had a lot of miles on them but still appeared good and useable. I have been told to replace the new seal because it may be damaged, but I am wondering if it may be that the drive axle end is worn.
I have seen this with harmonic balancers for engines. They even sell a replacement sleeve for harmonic balancers so you can re-use the old worn one.
View 6 Replies
I took the front axle shafts out a couple months back and remember NOT seeing any differential fluid in the axle shaft housing. But then when I took the tire off tonight.. I noticed diff fluid leaking from from the axle shaft dust seal ?
1. I didn't think diff fluid flowed up near those front dust seals ?
2. That's a brand new dust seal so I'm guessing some debri must be in the connection causing the leak ?
View 4 Replies
Not sure what caused it to break but my front driveshaft split in half. I had it in 4wd and was doing a K turn to back in my driveway in a snow storm.
I got underneath in the snow (miserable) and wasn't able to come close to getting it off. The bolts holding the shaft onto the t-case will not budge and the tiny 5/16" bolts stripped all my small 1/4" sockets. I'm guessing I need a 3/8" drive 5/16" for front and the rear just spins. Any tricks to getting this off the truck.
View 14 Replies
Can I take off the output flange on the tranny and use a slip joint, with out changing the tail shaft?
View 1 Replies
On my 2012 Camry XLE with 22,500 miles, just had the drivers side drive shaft assembly replaced, under warranty. Was getting a clicking sound when turning. Not too happy, car comes off warranty in September. They also updated computer on a recall for the torque shutter.
Then he tells me I need an oil change (was just done, oil shiny clean). He said oil looked dirty. Also said I needed a fuel injection cleaning (at 22.5k?), and new tires. OEM tires are garbage. Wheres the Toyota quality and integrity?
View 1 Replies
I bought this 2010 f150 from the company I work for, front diff was shot, front drive shaft was in the bed, that's all I knew about the truck so I bought a complete front diff from a used place, it only has 58000km on it, good diff... So I installed the diff and the old front drive shaft, which doesn't seem to be in the best condition, now when 4 wheel drive is engaged I'm getting a constant clunk/binding noise from the front driveshaft area. Where to start looking.
View 2 Replies
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
View 12 Replies
I am a new 6.7 owner and had/ have a 7.3 As I have been getting to know the truck I have been under it and noticed that the front drive shaft and axle are locked in. My hubs are switched to auto but I know on my 2000 7.3 when my hubs are on auto my front axle and driveshaft are disengaged... I'm wondering if the new 4x4 system is different. I know that can save on MPG
View 6 Replies
I recently bought a 1997 F150 4wd 5sp manual. While changing the fluids, I noticed that the front u joint on the rear drive shaft has a grease fitting. No matter how I rotate that shaft, I cannot access that fitting with my grease gun, even when fitted with a flexible rubber hose.
View 14 Replies