I heard a grinding noise coming from the right front tire last night. Came home, removed the wheel / tire and noticed the caliper was stuck pushing the pads against the rotor. I pushed the caliper pistons back in so they're not frozen, just sticking.
View 14 RepliesYesterday, I noticed that my right front brake caliper seemed to be sticking. This morning I jacked up the front end, and could barely turn the right front wheel when it was off the ground. So, I have concluded that that caliper is sticking. So, here is the question(s): what is the best way to repair this (new caliper, rebuilt caliper, or rebuild it myself), do I need to do both sides the same or can I just do the one that is acting up, and should I expect to pay. I have some mechanical ability, but that Haynes manual doesn't make too much sense to me. Getting it professionally repaired is extremely inconvenient, I need to be back at school (300 miles away) Tuesday evening, and probably couldn't get it in to get it done before then.
View 12 RepliesOne of the pistons in my driver side (UK) front brake caliper is sticking, so I've bought a second hand caliper just to fix the problem until I come to sell my pri in a month or so.
View 15 Replies2005 Toyota Solara my front driver side caliper was sticking and heating up a couple months ago... replaced the caliper and the rotor... still had the same problem. I would drive it, it got hot and stuck, after I parked for a little while it slowly released. Talked to a couple of mechanics and they both said undoubtedly I had a bad flex hose and it was collapsing with pressure and then will release... I changed the flex hose and flushed the fluid and it was immediately fixed...no problems.
Drove the car for a month, went to South Carolina and back and then a couple days ago the same thing started happening. Talked to a mechanic, he told me that the new caliper may have gotten fried from over heating before I changed the flex hose... Got a new caliper today (warranty) exchange... changed it out and still have the same problem. When it sticks I can release the pressure by opening the bleeder valve so it seems like the flex hose issue again... my only thought now is maybe the new flex hose is a bad one and someone mentioned the proportioning valve.
I just hit a pothole on my way home just now and now my front right caliper is sticking. It happen about 10min from my house. As soon as i hit the pothole I can feel my truck pulling to the right and felt like there was some resistance when i was driving. I got home and peeked my head in the wheel-well and i can smell the brakes burning and smoking a little. How would hitting a pothole cause a caliper to stick. Is there anyway to unstick it or am i gonna have to change that caliper out...
View 8 Replies2000 Ranger, see my sig.
Just had to swap out the pads on my truck yesterday. The pedal was pretty mushy and I was getting shaking in the steering wheel when the brakes got warm. Shaking wasn't all the time, only after they had been used quite a bit - say after city use and the brakes had to be applied suddenly. So I popped off the tires and swapped out the pads and replaced the brake fluid - flushed it.
On the driver side front, the pads barely had any real wear and the anti-rattle clip was all messed up. It was installed properly, but it looked like the pads had smashed into it. The rotor appeared to be warped, or at least out of round - but just barely. You could see it wobble slightly in one spot if you spun the hub with the caliper removed. The caliper itself was sticking slightly.
I didn't see any evidence of damage, the brakes flushed just fine although the fluid was incredibly dirty (because I haven't done it in a long while). On the passenger side front, the pads were worn down to the level I would have expected given the mileage. The wear was even.
My question ultimately is this - is the out of round hub the culprit here? Might there be something else going on like a caliper problem? Ultimately I plan on having the rotors surfaced - one of them certainly needs it and with new pads I might as well do it anyway.
I know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 RepliesStarted to change front pads and rotors on my GX470, but couldn't get the caliper bolts loose. Is it safe to use a torch to heat up the area around the bolts so I can loosen the bolts? Any other way to break these bolts free?
View 12 RepliesI have an 05 with a seized front caliper. What other vehicle has the same one? Does 4 runner or any other Toyotas have the same caliper?
View 5 RepliesSo I just did my rear brake pads and rotors a few days ago. For the last few months, my e brake hadn't been working well (have to pull it way up, and still weak).
While doing the brakes, I noticed the park brake arm was more or less seized on the left rear. I worked it a bit, and then my park brake worked perfect - 4 or 5 clicks, right on.
Then I noticed it isn't disengaging (brake smoke). I figured the ratcheting mechanism in the piston must be kaput.
So today I got a new (reman) caliper & bracket, installed it, and... still sticking. Cables are fine, the arm is moving fine. I'm now certain that the problem must be hydraulic, but what?
I would think that a master cylinder or booster would cause all the brakes to drag, or at least one axle worth, but that isn't the case. After a short spin on the freeway with little brake use, 3 of the brakes show 40 - 45C or so, and the sticking one shows 150C. (with an infrared thermometer).
During the brake job I noticed the left side was harder to turn in than the right, so I guess that could have been hydraulic back pressure somehow. Didn't seem to notice any damage to the hoses, they look pretty mint. master cylinder still?
I did the rear bearings at the same time. The bearing on the left was bone dry, probably from overheating in the past - I'm sure this POS stuck at some other time too, overheated and lost its grease. right side was fine but I figured might as well do them both.
I have a 2007 Sonata V6 I bought used two years ago. When I bought it mechanic serviced the rear brakes as the caliper was sticking. Now the rear brakes make a grinding noise when I brake and when I drive the rear brakes make a sound like slight metal on metal contact. I know Sonatas are known for brake problems. Should I replace the rear pads, rotors, calipers (including pins) and if so what brands are decent to buy? I have used rock auto in the past.
My car has about 198,000km on it (123,000 miles).
Have 50,000 mile on my 2011 F350 6.7 and up until today the truck has been flawless. This is my weekend vehicle and sees very light duty hauling fishing gear to my boat (100 miles hwy) and pulling my 7x12 enclose trailer with goose decoys. On a couple of occasions pulling my 29 CC from marina to my home and back. Took truck in for oil change and tire rotation, service advisor informs me I have 2mm on rear brakes and 3mm on fronts. Not sure why rears have more wear than fronts. Schedule to have brakes done for today and now find out that front right caliper is sticky and they want to replace both front calipers. I cannot believe that a 2011 SD F350 with 50,000 miles and of that mostly highway needs brakes let a lone calipers are going bad. Service manger tried to tell me that brake fluid should be replaced every 2 years, to which I responded that I have Ford perform all scheduled maintenance. He went on to say that this is not scheduled maintenance, wtf bs is he telling me, if it is necessary then it would be scheduled maintenance. Truck gave zero indication of stuck caliper, no sound and no excessive brake dust on wheel.
View 14 RepliesTwo weeks ago did a road trip to NH from RI and i heard a slight dragging only at low speed (10-15mph) in my left rear tire. figured the caliber was dragging a little, it was. Before arriving in NH the brake light came on. Long story short i get back to RI and the left side noise gets worse and starts to lock up. I finally replace the rotor which was warped, pads, and caliper which was bad.
Was driving it same day and still here the same dragging and screeching noise and the brake light is still on. On my way home the left side locked up at low speed without hitting breaks and slid the truck, mid you all parts are new on that side. I am not sure what it could be at this point something in side the axle?
Every time I am pressing the brake pedal, I hear a distinct clicking sound coming from passenger front Brake Caliper Area.
I have applied brake grease (green) to the pad shim.
I have replaced the spring sets on each front caliper.
Passenger Brake Clicking Lexus LS460L - YouTube
My 2004 Toyota Highlander with 84K miles has been diagnosed with a seized front driver side brake caliper with worn brake pad (1/32). I had recall work done a few days ago at the dealership and this was discovered afterward during the "complimentary" multi-point check-up. - You know, the long laundry list of recommended work they try to sell you on. Of course the brake work is actually necessary.
Since the vehicle was just inspected 2 months ago at our local shop, my husband suggested I take it back there to verify the diagnosis and see what that mechanic would recommend. That mechanic confirmed and showed me the seized caliper/worn pad, which, by the way, was functioning well in mid January at inspection, and measured 7/32. This mechanic recommends replacing both calipers, pads, turning rotors. There was no indication of a problem with the RF caliper, but he says it's just a good idea to replace it so we would avoid having another problem in the future.
I want to ask everyone's opinion regarding replacement of just the bad caliper vs. both. Are we getting ripped off as far as the estimate and is the flush necessary? Also, is this issue typical in the first place, and what causes a brake caliper to seize? We've had several other vehicles driven many more miles than my Highlander and never experienced a seized caliper.
At my last dealer performed oil change, he writes "CDM front caliper service due next time". He says something about needing to lube the front calipers .....
Is this service that should be done, or is the dealership service department looking for a chance to make money for unneeded service?
I had 15,000 miles on my 2010 Prius at that time. If needed, is it something I can easily do myself?
My front right caliper does not work. was changed ( both sides) also hose from right side because it still did not work. Found that fluid gets from reservoir to abs but does not come out to front right wheel. Place air pressure from hose to abs, and runs fine, from reservoir to abs and runs fine from abs to out from abs to front right and air does not go in.
But when pressure goes from out of abs to in abs from reservoir air flows fine also. What is going on...
I just noticed today that my passenger front wheel is sticking out further than my driver side wheel. I did a brief search and had a hard time finding anything.
I've read about shifting the subframe, but that only seems to adjust a few millimeters.
Pics of ball joint issue and difference in wheel tuck:
Notice the shift in the ball joint mounting on the passenger side. The driver side was replaced at the time of alignment.
Someone had worked on the car and front caliper pins got mixed up. Where the pin with the rubber piece goes into. The top or bottom of the caliper. and is it the same for both sides.
View 2 RepliesIt's time to replace the struts at 205,000 miles. Driver front is sticking and creaking. The dust boot was all ripped up. Either way the car is pretty boaty but I've never had a fresh Prius to compare it too. I got my car with 186K. I'd love to firm up the ride a bit but do see too many options. I see KYB GR2's, Monroe and Gabriel struts available. The car could use about 20% stiffer springs and some bigger sway bars. Any interchangeablilty with Corollas? They should have made a Prius S from the factory.
View 4 Replies02 Civic, 1.7L, 114K Found the front brakes sticking. I popped the bleeder open and got a little squirt out of the left side and a less of a squirt out of the right. I'm in the process of changing the pads which are on order from Rockauto. I took the existing pads off and lubed the pad guides/holding slots but I felt them starting to drag again after a short test drive. Also they did not seem to respond properly with normal braking. How would I test the caliper(s)? It's got to be a bad caliper or master cylinder causing this and I just don't want to throw parts at it.
View 19 Replies