Lexus GX 2004-09 :: Auto Windshield Wiper Malfunction - Sensor Going Bad?
Jan 20, 2015
My auto windshield wiper function has become real sensitive...When driving in the lightest rain or even mist, my wipers start intermittently, then go faster and faster until they are going steadily, and in medium-light rain, often go to high speed. They never did this in the past, this has recently started. I turn them off, then back on and the process repeats. The auto wiper was always wonderful in the past, but not now.
Is there some kind of adjustment for this problem? Is my windshield sensor going bad?
View 11 Replies
Advertisement
This is for a 2003 GTI, 89,00 miles. Every time I try to use the windshield cleaner the fuse blows for the windshield wipers. I have tried to put in a 25 amp fuse and it worked for a while but still blew. The windshield wiper motor has been replaced.
View 2 Replies
When temperature is lower than 15 degrees windshield wiper fluid freezes in supply line or squirter. Is this because of the cover at top of inside of the hood? Does that cover prevent engine heat keeping the system operable at lower temperatures. We need this system operable in the mountains of CO where ice melt is spread on the roads.
View 4 Replies
I noticed my 2005 GX470 started to "bottom out" when going over speed bumps or potholes. The air suspension seems to work fine raising and lowering ok and the general ride is still quite smooth. From some simple searches on the board it would seem that leaking of the air suspension could be the problem?
I did a code read and got the following error codes none of which sem related to the problem.
Code
CO200 Right front speed sensor malfunction
C1223 Malfunction in ABS control system
C1340 Open circuit in central differential lock signal
C2172 tire pressure, transmitter identification number not registered
View 2 Replies
My 330 had a new windshield installed prior to purchase and shortly after, the rain sensor module came loose. Cleaned things up and epoxied bracket in place, and about a year later it came loose again. Seems temperature related - a hot sunny day and the epoxy loses adhesion. I'm ready to try again but at odds as to what adhesive to use. Any long term successes out there?
View 5 Replies
I may need to replace the rear wiper and could not figure out how to access it because in the OFF position it is hidden by the top spoiler.
Short of turning off the engine when the wiper is in the down position, how it supposed to be accesse?
View 14 Replies
06 GS300 Drove all day in freezing rain, but when I went to leave the store, the drivers side windshield wiper decided to stop working. I was able to make it back to the parking lot. The passenger side is working fine, but that was not working for me at the time. What could have caused this issue?
View 4 Replies
Just got my second sc, after I crashed my first one and the little button that releases the wiper fluid to clean the windshield is gone, how I can find such a small part? Does the sc300/400 use the same wiper lever/arm as ours?
View 5 Replies
My windshield wiper spray doesn't work. The juice just kind of sputters out, it doesn't shoot out. The tank is full, and the rear-window wiper nozzle works fine. What are some things I can do to troubleshoot this?
View 2 Replies
Is it just as simple as when the wipers activates when it senses water drop on front windshield? the sensor is turned on and it started to not work time to time recently. What's going on?
View 14 Replies
I recently purchased a '09 LS460 SWB. I noticed the driver side windshield wiper arm sitting up high enough to be in my field of vision.
I'm aware that there is a "winter mode" that allows you to raise the arm up a few inches, but from everything I've read....usually the driver and passenger side arm raise together.
In my case, my passenger side arm sits nice and low near the hood, while the dirver is sitting an inch or two higher.
I tried pushing the driver arm down (with success), but after cycling the windshield wipers once, the driver side arm goes back to the higher position.
View 8 Replies
Troubleshooting the wiper fluid spray system in my 2007 Prius. So today, after the big winter storm here in New York, I had to go out and run some errands. Everything was working fine, used the wiper fluid spray a few times during my drive to keep my windshield clear. When I was about to get home, I tried to spray the windshield one last time, but no fluid came out. Also tried the rear sprayer and no fluid came out of there either. The first thing I did when I get home is to check the wiper fluid reservoir, and there is plenty of wiper fluid in there.
I can hear the pumps whirr when I tried to activate the wiper fluid spray, (tried both front and back, both have the pump whirring sounds), but no fluids sprayed out.
I'm thinking maybe something got clogged in the wiper fluid spraying system somewhere. Is this something I can try to fix myself?
View 3 Replies
When I tried to spray fluid into front windshield fluid is coming out very very very little on left and right side wipers, do I need to add any liquid or any problem with that..?
View 9 Replies
So over the past week of driving my new 2011 RX350 I have had the auto wipers set to on so when/if it rains they automatically come on. However at random times when there is no rain the wipers come alive an make a sweep across the windshield.
View 14 Replies
My dealer says the windshield on my 2012 RX 350, which has < 8k miles, has to be replaced in order to fix the auto rain sensing function. Even though it is covered under warranty I'm confused and not happy with this. What is in the windshield that causes the problem? Could it just be the control sensor behind the rear view mirror, which they detached in their troubleshooting?
View 9 Replies
I have a 2007 ES350 with 90k miles. Purchased in August. I had ignition coil go out and decided to change them all and the spark plugs. When changing cylinder 5's coil and plug, I tried to push the wiring harness out of the way to remove the coil. Result, I moved the wiring harness too far and disconnected the 3 wires (black, yellow and red) that were connected to the cam position sensor connector. (I should've just removed the sensor SMH) I disassembled the connector, got it down the internal pins, soldered the pins to the wires, placed the pins back in the connector and reassembled it with the wires in the order that they appeared to originally be.
Plugged it back in and put everything back in place. Started the car and code P0352 was cleared but replaced with code P0365 Camshaft Position Sensor B - Bank 1 Circuit Malfunction. I'm thinking, either I put that pins back in the wrong order or one of the wires isn't properly soldered in. Either way, I ordered another connector and it should be here tomorrow. I need Either a wiring diagram or a picture of the camshaft position sensor closest to cylinder 5 connected with the wires in the proper order .
View 14 Replies
2004 f-150. When I put the light switch in "auto" position and it gets dark, only the parking lights come on. The headlights do not come on. The headlights work when I put the switch in the "on" position, however. This makes no sense to me.
View 1 Replies
I have an ABS light on. I have crawled under the truck I don't know how many times everything is connected just as it should be. The wires did have to taped up because they burnt into after getting against the exhaust at some point, but I had fixed that awhile ago, I've even tore back into the tape and re-did everything again, nothing gets rid of the ABS light. When this first happened it would go away after I turned the truck off, but would come back after using the brakes a few times, especially harder stops. Then it got to where it just came on and stayed on, and didn't go out no matter what. Thinking my ABS speed sensor went, I bought a brand new motorcraft one from rock auto it fits perfectly in the rear, plug looks good. I can't find NOTHING that would keep this light on. The code is always the same "Rear ABS Center Speed Sensor Input Malfunction", how to get rid of this?
View 1 Replies
I was plowing and when I put it in reverse it felt like it slipped, but then the dash message trans malfunction came up. I checked the codes and I got P0722 output shaft speed sensor.
Code P0720 (oss) sensor circuit fault
Then the truck went into safe mods. Is it just the sensor or is my reverse going out...
View 4 Replies
I put a new wiper mechanism in my 02 Camry, and I think I left something out.
The wiper motor is in there swishing away and the wiper blades aren't moving. I removed the mechanism and found that the small arm that makes it all rotate keeps loosening. It's a nut which I'm sure needs a spacer or something to keep it from unscrewing itself.
View 1 Replies
I finally had enough of the annoying squeak-squeak-squeak of my wiper blades every time I used them. Time for a fix!
First, I narrowed down the problem by making sure it was not the rubber wiper blade rubbing against the windshield. You can rule this out by simply lifting the wiper arms up to the locked position and turning them on. If they still squeak it’s not the rubber rubbing against the glass.
By carefully listening I narrowed down the squeak to be coming from under the large black plastic cover on the passenger side wiper. From what I have read other Gen II Prius owners have had this same problem. I discovered that you CANNOT remove that cover without removing the wiper arm assembly. But it’s not too hard.
View 2 Replies
