When I back up in reverse with my steering wheel turned all the way counter clockwise, I get a rub in my front passenger wheel well. Nothing is hanging down or loose that I can tell in the wheel well.
View 3 RepliesI have a '95 F-250 7.3 auto 4X4. The transfer case linkage has been floppy and prone to coming apart since I've had it, but that's been fine for me. I let my brother use the truck last weekend, and now it does the following: When you put the transmission in reverse, or when the truck overruns the engine (compression braking) it grinds badly like the transfer case isn't quite engaged. Only does it in 2 or 4 Hi, and everything's normal otherwise.
Could the transfer case have jumped out of gear while he was driving it, and he didn't know to either push it into gear or pull it into neutral before it did damage? I really don't want to pull a transfer case in my driveway in December in New England, but give it to me straight.
Noticed that both rear wheel hubs don't spin freely, they rub or grind. 2013 Elantra sedan gets about 10% worse MPG than a 2012 Elantra we traded in for it, two identical cars yet 2012 got much better MPG and now we notice a rubbing noise on the 2013.
2013 Elantra has 19000 miles but has always had reduced MPG, markedly worse than the identical 2012 we traded, but dealer could never find a problem with 2013.
Wonder if this rubbing on the wheel hubs is to blame for the lower MPG? I can't think it works. Not sure if its the emergency brake, the power brakes, the wheel bearing or something else.
Is this rubbing noise normal? Rubbing happens with the hub only or even with the wheel attached to the hub.
So this is my first 4wd vehicle. I read that to put vehicle in 4wd when the car is running, put the car in neutral and shift the 4wd stick to H or L depending on the driving condition. When I do that, it grinds a little before slipping into the mode. Is this normal? Am I shifting it into 4wd incorrectly? Also, when doing normal road driving on pavement (no rain or snow), should the car be kept in H or N on the 4wd stick?
View 10 RepliesWhere the this ecu is located. I believe it's behind the glove box, but I want to be sure before I take it out again, wasn't sure which connector it belonged to. 2006 GS300.
View 2 RepliesDriving my 2008 460L and I get the brake sensor warning. Ok I've been through this before and know I have a little time left, but two days later I get a little grind noise. Then suddenly metal on metal what the hell is that noise! Turns out the passenger side rear lost a pad... it's just gone. The plate is left but the pad is gone on the inside of the rotor. The outside still had about 25% left. The other back wheel still had about 25% left on both pads.
I have 97k on the car and the rotor was turned on the last brake job so I assume I am done with this rotor and order a new one. Now the fun... I pull off the caliper and compress the cylinder on the offending pad first. The way I do this is with a big pair of channel locks I put one jaw on the pad and one on the back of the caliper and squeeze. It works a treat so I pull the offending pad and the dust boot falls to the ground in pieces. Great... now I put the channel locks on the other pad and when I squeeze, it goes in very easily with almost no resistance and the cylinder on the other side(with no boot on it) shoots out along with a bunch of fluid, probably 4-6 oz.
I decide to reassemble everything knowing I now need to bleed the brakes. All of the other wheels are normal and the brake job goes smoothly.
Frustrating part is here... how do you bleed the brakes in this car?!
methods I tried:Gravity - open the bleeder valve and let it drip, the dripping stopped after 20 minutes leaving no fluid in the line or caliper at all.
vacuum - I used the hand pump tool to try and pull fluid thru, got little spits and dribbles at best.
traditional - had my son pump the brakes, he could get a spongy pedal that bottomed out but never a firm pedal and the cylinder remained empty.
pump and suck - aggressive pumping of the pedal with the suction device on the hardline nipple. This resulted in a little fluid coming thru but no where near the amount you'd expect.
Now I have VSC, Brake Malfunction, ABS warning on the computer.
I first noticed this recently as my wife was pulling out of the driveway into the street... The car wasn't cold, as it had been running for a bit over 5 minutes, warming up. My driveway slopes a bit towards the street and also has a dip/hump at the end of it. As she pulled out in R from P, I heard a thump. I also hear a noise which sounds like the brakes engaging. So in order, brakes engaging, shift from P to R, the thump then as it backs up and turns into the street, there's a slight, faint grind noise.
As the car stops to go from R to D, it thumps again. But as it goes into drive and pulls away..smooth as butter and quiet. I've heard and read that it's possible motor mounts. I'm wondering if the light grinding is the actuator...or perhaps dried out bushings in the control arms... Also read the possibility of the trans going bad, which I highly doubt, but who knows. My plan is to call Lexus in the morning and see if I can be squeezed in.
I'm up to 102k on my 2007 Azera Ltd. In the last two weeks I started getting a grinding/rattle type noise when I turn my AC/Fan up to the higher levels. When it's on low/mid you can't hear anything. Does this mean the compressor is starting to go or is this something else going on?
View 5 RepliesOwning a Lexus . I recently bought an '06 model GS300 and have just had an issue appear with it.
Issue is that, whether in drive or reverse, the car accelerates on its own - not very quickly, but quickly enough that it'll crash me into my garage door if I'm not careful.
What this could be? Variously, I've read that it could be a Throttle Positioning Sensor, or Idle Air Control valve. Some things I've read suggest it could be air conditioning related (though I don't understand that one...).
I was trying to find a guide on how to change out my reverse lights to LED, I'm having problems removing the panel. The guide i found on here had all the pictures removed. I'm also trying to change the lights for the make up mirror.
View 14 RepliesIs there anyway to view the backup camera when the car is not in reverse? During driving, while stopped, etc.?
View 14 RepliesI have a 2006 F150 STX auto trans with the 4.2L V6 that has been having intermittent starting problems. It has 98,000 miles on it. It will start fine 99% of the time but sometimes when I turn the key the starter will grind once or twice then it can go a few weeks with out doing it at all. Then also sometimes it will crank turning over for several seconds but wont start. Then it starts fine the rest of the time. This has happened several times but only happens once every few weeks or so. Just trying to see if it needs a new starter or if its something else. It has a new battery.
View 3 RepliesHaving issues with brake noise when only in reverse? I have extremely loud break noise only when I reverse out. Could this just mean I need to get a break change?
View 14 RepliesJust bought this 11 gs350 and car is great except that the reverse camera does not activate when the car is put in reverse. The side mirrors tilt down and the rear shade will lower when put in reverse but the screen just stays on the navigation screen no flicker or black screen.. What could be the problem?
View 7 RepliesExcellent feature since I park in the city along curbs all the time. I know you have to have the button lit in L or R for the feature to work. Initially, I only had to push L or R once and it would stay lit all the time, but just recently, I have to push L or R every single time I drive my car to use the feature. Just a minor inconvenience, but what did I do and how can I fix this so I don't have to push L or R every single time I drive my car to use this feature?
View 3 RepliesI have a 2008 GS350. Been having brake clicking when I move from reverse to drive and lately been happening more when driving regularly. Brought it in to Lexus to get the complimentary 19-point inspection and they said I needed new brake pads and rotors. I did do a search and found it can be issues with front spindles, sway bar, bushings.
View 5 RepliesI have a '07 GS350 RWD with 121k miles. I had my transmission fluid drained and refilled at 90k miles.
Every time I go into reverse, there's a clunk noise. But all my gears shift smoothly.
I have a 07 GS 350 and my side mirrors don't point down all the way in reverse than when I put it in drive the mirrors don't adjust to my preset.
View 4 RepliesWhen shifting from reverse to park or drive, the mirror tilts back up but not in the position it was prior. It is actually quite irritating because I would start driving and have to adjust the mirrors back to the desired setting. I've also just sat there and shifted from park -> reverse -> park and recalled the memory setting and I will see it make the adjustments.
View 8 Replies2007 GS350 ... Mirror only moves down sometimes when I shift into reverse. Malfunction started about month ago.
View 14 RepliesI just got a 2009 lexus gs 350 everything is perfect except when i go into reverse and back up slowly the brakes make a loud squeaking noise!! Its really annoying and embarrassing. I got the rotors resurfaced and nothing.
View 3 Replies