Lexus GS 2006-11 :: Check VSC Error Code P0300 With Check Engine And Traction Light On
Mar 12, 2016
A few days ago my "Check VSC" warning came on along with the check engine and traction lights being on. I left my car in a parking garage for a week when I was on vacation and the lights came on once I started the car after getting back from my trip.
I have had the "Check VSC" warning before and I fixed it by replacing my gas cap. My gas cap seems fine this time around so I got my codes scanned and the only one that came up was P0300. Having this issue with the 2007 Lexus GS 350? I still feel like it's my gas cap because I bought a cheap replacement last time around.
View 8 Replies
Advertisement
Mystery issue with my 2001 Accent GSI (5-speed manual, 1.6 L). I'm getting a P0300 error code and the Check Engine light (the light is like an old friend, I miss it when it's not on). This happened four months ago and I replaced the ignition coil - seemed to fix things - but now the light and the error is back with a vengeance. Car stumbles and runs rough. Changed the plugs and plug wires, but no difference.
BTW, there's a small pin hole in the upper part of the gas tank (just enough to give it a gassy smell when the tank is full) but I don't think the hole would be big enough at this stage to cause the check engine light to come on in the same way it does if you leave the gas cap off or loose.
View 3 Replies
I was driving home and all of a sudden my rpms are at 3.5 4k rpm wont shift to next gear. I put in in tiptronic mode and shift it to 8 it works fine. Then about 10 minutes later check vsc shows on dash traction control light is on check engine light is on and the light next to the check engine i think it is the abs light. I havent pulled the code yet.
View 1 Replies
I know it is a random cylinder misfire code however I started my car in the morning and it was fine I moved it and put it back in my driveway. I started it up later and waited for it to heat up i came back outside 10 min later and my check engine light was flashing and my car was shaking like crazy you could tell the engine was misfiring like crazy. I had under a quarter of a tank but not empty yet. I shut it off and turned it back on and it was still doing it. I drove the mile to the gas station the way it was.
Under partial throttle it was revving to 4500 and over 5, had to let of throttle to make the car shift up a gear. I filled up and started the car again performed fine after that however the check engine light was solid now and still on. I went to my local mechanic and he read that code P0300. I changed my spark plugs that day and they were crap the original spark plugs I have 65,xxx on my car now. Car is smooth now. I cleared check engine when i saw him first and it did not come back on all day even before i changed the spark plugs later that night. Why my light was flashing and why my car was acting like that till i filled up?
View 6 Replies
I have 2006 Lexus GS300 with 95K miles. My check engine, check VSC and traction lights came on. I get an error code: "P2757 Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance or Stuck Off ". I was given the following different solutions that may work: replace the solenoid, service the transmission or replace transmission.
View 14 Replies
I recently bought a 2007 Hyundai Sonata Limited from a private seller. This car has been perfect for the few weeks I've had it. Now, my check engine light came up and the error code "P0660 Intake Manifold Tuning Valve Control Circuit / Open Bank 1" popped up. I'm not really sure what piece to look for, or which connectors to check.
View 3 Replies
From time to time, the engine lights comes on with error code P0365, it usually disappears within two days (it disappears by itself), but it appears once per month and stays for two days.
The code scanner says :P0365 Camshaft Position Sensor B Circuit Malfunction (Bank 1)
Do I need to change the sensor? and where is it located?
my Sonata is 2009, 2.0L (Korean imported) 4 cylinder ...
View 8 Replies
My Lexus was working fine till yesterday, but today when I started (button press) it, it started giving me a Check VSC error and Check engine light along with Slip Indicator started showing up
Took it to Autozone for the codes and got
P0015
P0304
C1201
B2799
View 7 Replies
Check engine light came on. Codes are P0300, P0302, P0304. Plugs were previously changed. Plugs look good. Changed both coils. Light still one. Injectors also previously cleaned. What else should we check for? Valves hanging? Anything else to check for?
View 5 Replies
VSC, Check engine light just came on my 2006 GS300. I only have 50k miles on it. I had this happen a few years back and it was the Gas cap o-ring. This time I changed the gas cap and reset the codes but no luck. After starting the car, with a minute the lights come back on. So checked the code and here is what I'm getting:
P0031
Heated Oxygen
Sensor Heater
Control Circuit Low
Bank 1 Sensor 1
Doing a search for the code yields this: [URL] .....
Changing the sensor vs. checking something else that might be the issue?
View 4 Replies
I have 07 350 and my check engine light is on, i had it scanned and they told me that the code is BP0013 and bank 1 Cam position sensor is bad. What that code means and where is that sensor located???
View 9 Replies
I have a 2006 lexus gs300 rwd and my check engine light came on the code P0021 and the check VSC light is on as well and a knocking noise i checked my engine level and seems to be fine but thats just because im always adding oil since its burning a quart every 500 miles which is a lot so whats going on here? Also my idle seems to drop when at a light any one know about recalls on these cars?
View 4 Replies
2003 1.8t passat wagon. 50k miles... The check engine light came on today. Oil and engine temp are fine. Can most shops plug in and diagnose? Can I get one of those code readers at Advanced Auto parts to read the error code?
View 5 Replies
What is the meaning or the fault concerning 4608. The above error code was reported on the computer diagnose machine and it referred me to look into the vehicle ownership manual book BUT its rather unfortunate that i could not find that book. So, what to tackle or replace on the engine to enable the check engine lite go off.
View 17 Replies
I got a P0118 error code on my car. Looked up some things and most people were saying change coolant temperature sensor. I changed it 2 days ago and have not had a chance to clear the CEL. Its still on now, guy at Autozone would not clear it, said it was against company policy.
Will this turn off automatically once problem corrects itself? I went to Autozone and had them rescan the error, this time another code poped up P0444, EVAP(Evaporative Emission System)Evaporative Emission Control System Purge Control Valve Circuit Open. What this can be?
View 3 Replies
I have a CEL on my 2007 Avalon so I decided to take it to Autozone to get a scan. Error code P0015 was returned. This code has to do with B Camshaft Position, Timing Over Retarded (Bank 1). I've done a little research and I've read that this could possibly from a dirty screen on the Oil Control Valve, the OCV itself, or the Cam Position Sensor. Before replacing parts, what I would like to do first is to check/clean the screen on the OCV. Secondly, I would like to swap the Cam Position Sensor to a different bank and see if the other bank throws an error. If the other bank throws an error, then I know the sensor is bad and needs to be replaced. With this said, I am having trouble locating the OCV and CPS. Where the valve and sensor is located. A diagram would be useful.
View 14 Replies
I got a 2012 Hyundai Accent SE manual 112000 mostly highway miles. For a month now I am getting the MIL on and P2191 code (System too lean at higher load bank1) after erasing the code it appeared again in 3-4 days. I replaced air filter check all valves and vacuum in air flow, changed to premium gas. Pipe that connected to the valve from EVAP system looks not damaged and valve works as intended. While changing spark plugs I noticed that all of them were quite charred. I am thinking to replace both O2 up/down stream sensors. Which not OEM sensors would be the best match for my Accent?
View 11 Replies
My car just turned 85k miles. The day it turned 85k, I recieved a message from dealer saying their records indicate car is due for 85k service. Coincidence? Note: I do not have my service done at the local toyota shop. They have not seen car since last warranty work probably 2+ years ago.
Also at about this same time, the service engine light came on, (oil change needed). Since I only use mobil 1 in the car with genuine Toyota filters, I am not to concerned if the car gets another 500 miles on it while scheduling a service. However, this time, returning from a short trip on Sunday, the VSR (traction control) and the check engine light came on. Only Code is p0015 left bank. Monday, warning lights are gone, and oil change is scheduled for Wednesday.
Is the VSR and the P0015 related.
View 4 Replies
I am far from home. Taking a road trip. Day 2 out of 6. My check engine light came on, so I just pulled over. All fluids were fine. Found some place to read the code:
P2757 TCC pressure control Sol Ckt Perf / Stuck off
The guy said it was something to do with trans.
View 3 Replies
I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.
View 14 Replies
I had a Check Engine Light a couple months ago, and I took the car to the garage to have it checked out. They told me they got a Fuel Pressure Sensor malfunction code, and that the sensor had to be replaced. I did so myself, an it is ridiculously easy, and the car worked fine. I noticed the Check Engine Light blinked a couple of times while I was driving, but never got steady. A couple of days ago, it did. Out of a bad gut-feeling, I purchased a ODBII scanner, and I scanned the car myself. I got the same error code as the garage did, but the sensor should be fine.
View 5 Replies
