Lexus ES 2007-12 :: Got Error Code C1201 / P0057 / P0161
Jun 12, 2013
So I just bought a used 2007 ES 350. One week into ownership the check engine light, vehicle stability light (car with swerving tire tracks) and check vsc lights all come on.
I got the codes read and they are C1201 P0057 and P0161.
The last two I believe are oxygen sensors and the first is a vague engine control problem?
The lights come on for a few days, then go away for a few days.
The non-Lexus dealer who sold me the car sent me to a mechanic who says the lights will likely go away all together if we just replace the correct O2 sensors.
The car also vibrates when moderately applying the brakes at speeds higher than 60 mph- is that normal?
View 3 Replies
Advertisement
I need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
View 12 Replies
2007 camry 3.5q... I got my engine scanned and the code was p0057. I already replace my two oxygen sensor but the check engine light and check vsc system still on. What will i do?
View 1 Replies
Tonight, during a short ride, all the sudden the VSC TRAC, VSC OFF and Check Engine came on. Atfter home, I got the P0057 code from a OBDII scanner. The P0057 code indicates O2 sensor on bank 2 lower sensor. However, the interesting thing is I also lost the power seat adjustment on the seat memory. When I switched between L1 and L2 , the mirrors and the steering position changes and the seat did not. However, the adjustment buttons on the seat itself work correctly. I wonder if this problem associates with P0057?
View 4 Replies
2007 Lexus ES350 with 177k miles. Getting a P0368 (Camshaft Position Sensor B Circuit High Bank 1) Error. I can't seem to find online where this sensor is located at.
View 2 Replies
How to reset and remove the error code on the tire pressure monitoring system?
View 5 Replies
Light did not come on for a while then it finally did. I replaced all plugs & that did nothing, almost made it worse. Put a scanner on it & it reads bank one lean, misfire. i unplugged all the coils one at a time on the drivers side & didn't notice any drop in rpms. On a side note, the exhaust leaks a bit of water out of the tailpipes a bit at idle.
View 3 Replies
Just started the truck after not running for a few weeks and drove around fine. Looked down and suddenly a CEL was indicated. Checked it with my Edge Evolution diagnostic mode and Code P0161 came up 2nd bank downstream heater circuit fault. I've also have an exhaust leak in the right passenger side exhaust manifold for about the last year. I've been waiting to install my newer 03' used engine when time and funds permit.
View 3 Replies
I'm getting code P0057 with my OBD II code reader. This is what shows up..
H025 Heater control circuit low bank 2 sensor 2
Is it the code for the 02 sensor???? 09 Camry V6
View 3 Replies
2002 Lexus SC 430 Getting codes P1351 po302 and c1201.
The engine is running shaky. If you just hold your hand on the steering wheel you can feel the engine shaking.
The car has brand new sparkplugs. What could the problem be?
View 6 Replies
I own a 2002 SC430 with 20,200 miles on it which I purchased new. The other day the check engine light came on. I checked it with the code reader and got the following 2 codes. P0300 (random multiple misfired detected) and C1201 (engine control system malfunction). The car ran great before, now running real ruff and when you drive it has less power.
View 9 Replies
So of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
View 2 Replies
My 2007 Camry SE has an intermittent electrical issue. The problem started yesterday, no accidents of any time ever in the car. 195,000 miles on car.
As I was driving along the speedometer, tachometer, temp gauge all started bouncing. Simultaneously the ABS and Emergency brake light came on. The engine did not change, still drove fine. I got the code U0073. I checked a couple obvious fuses like ABS and Alternator as well as cleaning the contacts on the computer at the actuator. I've also checked my battery terminals -- fine.
I am hoping to narrow something down other than just going straight to replacing that ECU by the actuator. That is an expensive part not to be 100% sure of it, but as it stands now I would almost rather it be something "simple" like that because chasing these electrical phantoms is quite aggravating.
Also all the items I have focused are based off the assumption it is something electrical revolving around the ABS unit. Is it possible the instrument cluster is the culprit, wiring in the harness or a simple fuse related to that panel?
View 14 Replies
What can be done regarding these faults? P0037 and P0057
Description:
Oxygen Sensor Heater Control Circuit Low (Bank 1, Sensor 2)
Oxygen Sensor Heater Control Circuit Low (Bank 2, Sensor 2)
The catalytic converters have been removed but the fault was present before that anyway. All I want is the VSC function to work again and the lights to go off. I have heard you can put dummy sensors in.
View 3 Replies
Check engine light is on, when I went to get my car inspected it was showing an invalid vin code. How do get this off so I can get my emissions done?
2007 Santa Fe SE
View 3 Replies
Car was perfectly fine. Parked it in a parking spot, turned it off for a minute, started it back up, and BAM, Master Indicator Light is illuminated(not blinking), along with check engine light. (yellow, not blinking)
Code reader gives me these two codes: P0ac0 and P0afa
View 2 Replies
I have a 2008 model 2.7 v6 with 80000 Km, and I would like to share my experience with several issues:
- Random misfire: brought the car to Hyundai, very bad response. I bought online the wiring of the spark plugs (according to them that was the reason of the misfire) and they installed it, did not improve. The car was still showing error code after clearing, and the fuel consumption at an average of 23L/100km.
- I then decided to change all the 6 spark plugs, no difference. The workshop told me the coils were in perfect condition. Still having a message like this: "ignition error on 2 or more spark plugs".
- I did a complete cleaning with contact spray of the MAF sensor.
- I bought online a couple of ignition coils, being original Hyundai ones, and changed them. When installing them i realized the existing ones were not original Hyundai and had a small marking, making me think they were recycled or chinese stuff.
- Having done that, the OBDII shown two more error codes: P341: error on camshaft position sensor, P2189: fuel idle (too much air, maybe caused by the first one). Changed both camshaft position sensors and then big change in the behaviour, more response, throttle, better gear switching.
- I so concluded that the 4 remaining coils have to be changed and ordered another time 4 of them online. OBDII showing now only one error code: random misfire. The engine going much better than all i got before.
- I have decided to take advantage of this order and also ordered a new TPS (seeing here that it was a common problem) and a Crankshaft position sensor (in order to prevent any other issue).
- I also changed previously 2 downstream o2 sensors that were giving an error related to emission. Emission here are not strictly controled so it is not a big issue.
My question is, what in all that sensors can more likely make my car burn 23L/100km??? Asian cities are quite similar to american cities, lots of highways. This consumption compared to what you describe is way over the normal one isn't it? I was assuming the ignition problem was the responsible, am i right?
View 54 Replies
I have an issue in my car (Santa fe 2011) and it occurred since it was new (ODO 3000 KM , ESP light is on and the 4WD Blinking) . the agency could not resolve the issue. and my car up to now been in and out from the workshop for more than 6 times . and more the error code ( C1627 ) that appears in the GDS(Global Diagnostic System) does not exist in the system (troubleshoot manual) .
View 5 Replies
I have an 07 passat with a 2.0 4 cyl turbo and I have an error code of P0171 system too lean (bank1) but engine seems to run just fine, what this code means, am wondering if it is something I can fix or if it needs to go to the shop??
View 2 Replies
I can't get the key out off the ignition with out playing around with the shifter button and brake pedal, an error talking about a steering column lock shows up some times.
View 3 Replies
I used Maxidas for scanning my GX470 05 and I have error code C1336 ... How to resolve it ?
View 8 Replies
