Lexus ES 2007-12 :: Code P0365 - Camshaft Position Sensor Circuit Malfunction On ES350
Jan 8, 2015
I have a 2007 ES350 with 90k miles. Purchased in August. I had ignition coil go out and decided to change them all and the spark plugs. When changing cylinder 5's coil and plug, I tried to push the wiring harness out of the way to remove the coil. Result, I moved the wiring harness too far and disconnected the 3 wires (black, yellow and red) that were connected to the cam position sensor connector. (I should've just removed the sensor SMH) I disassembled the connector, got it down the internal pins, soldered the pins to the wires, placed the pins back in the connector and reassembled it with the wires in the order that they appeared to originally be.
Plugged it back in and put everything back in place. Started the car and code P0352 was cleared but replaced with code P0365 Camshaft Position Sensor B - Bank 1 Circuit Malfunction. I'm thinking, either I put that pins back in the wrong order or one of the wires isn't properly soldered in. Either way, I ordered another connector and it should be here tomorrow. I need Either a wiring diagram or a picture of the camshaft position sensor closest to cylinder 5 connected with the wires in the proper order .
View 14 Replies
Advertisement
2007 Lexus ES350 with 177k miles. Getting a P0368 (Camshaft Position Sensor B Circuit High Bank 1) Error. I can't seem to find online where this sensor is located at.
View 2 Replies
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
View 6 Replies
My 1.5L 2000 Hyundai accent is reading p0342 code.(cmp sensor circuit low Input). I have changed out the sensor from a parts car and it's still reading this code. I've read it could be timing or an issue with the starter wiring.
View 3 Replies
I am having a problem repairing my 1997 aerostar with a 3.0 engine. Code PO340 comes up. Ive replaced the cam sensor, cam sensor housing and the pcm. Using the diagnostic charts, I've thoroughly checked out the wiring, in the harness, at the sensor, and at the pcm. I've set the cam sensor housing at TDC with the appropriate timing tool. Code P0340 still comes up. I've seen a couple of other aerostars with the same problem. Ford TSBs .....
View 14 Replies
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 Replies
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
View 4 Replies
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 Replies
I am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 Replies
I have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 Replies
The computer is returning P1379 camshaft position sensor. Where is this sensor located on a 2002 Toyota Camry 2.4L and how easy would you rate the job of replacing it?
View 3 Replies
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 Replies
I have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
View 4 Replies
I have a 2007 Camry V6. Last weekend, I changed all the spark plugs and five ignition coils. (117,000 miles on car). In January, I replaced the #6 ignition coil. Last week i threw a code for the #2 coil. Fearing the domino affect, I replaced all five remaining coils and changed all 6 spark plugs while i was in there.
Now I am throwing code P0368. This happened immediately after i changed the coils and plugs. What is this about!?!?!? Ive driven it maybe 40 miles since the plug/coil change...engine light is on the whole time. Is this sensor bad or does my car need time to "rethink" with all these new parts ...
View 14 Replies
I have been getting a P0011 error code. Changed the OCV but the code continues. I'm going to try replacing the CMPS but am not quite sure of the location on the 2007 Sonata GLS. Looking for any pics of the location or a description?
View 1 Replies
I have a 1997 Toyota Tacoma 3.4L ... After having some problems a week ago with the truck dieing at every stop sign or any time my foot wasn't on the gas. Eventually the truck would not start at all. I finally got a CEL that gave me P3040 (Camshaft Position Sensor Circuit Malfunction) So I changed out the sensor and the truck fired right up and ran for 3 days.. Now the truck does not start again and I am getting the same CEL code.
View 1 Replies
My check engine light came on the other day, and I went to Autozone to have the code read. Of course, that indicated the camshaft position sensor was detecting a fault. I read through all the posts relating to the fault, headed up to my local Hyundai dealer, and picked up the oil flow control valve for about $50 plus tax. While I was there, I figured I might as well have them do an oil change, since it was way past due. No point in putting in a new part with dirty oil..right? They did the oil change, washed the car and I was ready to roll. My plan was to replace the part myself, but magically, the check engine light has not come back on since.
View 8 Replies
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 Replies
My wife's 2003 Altima has been stalling. The MIL came on P0335 Crankshaft Position Sensor Circuit. I did a little research and it seems that it is pretty common for that sensor to go bad, so I bought a new one. The problem is I can't get the wires off the old one. It is in such a ridiculous place. There is no line of sight anywhere. It has to be done completely by feel. Supposedly, I should be able to push the button until it clicks and then remove the connector. When I push the button, it definitely clicks - but it doesn't stay clicked. It clicks right back out before I can pull on the connector. How can I keep that button clicked in when I can't see anything and I can just barely get one hand down in there?
View 19 Replies
This is what I get from the DTC .....
DTC P0705
Description : transmission range sensor circuit malfunction
State : History
I have done some google search on the above diagnostic trouble code P0705 and as i understood , it indicates that the Engine Control Module (ECM) has received an input error from the Transmission Range Sensor (TRS).
Since the check engine light illuminated two times (two separate occasion) then it turns off now; the ECM is actually receiving input signal from the TRS.
So that leads me to think that the TRS is actually working but the problem might be one of the following two:
1- Open or short in the TRS circuit?
2- Dirty transmission fluid.
What do you think the steps i should do first of all ? how would i check the transmission fluid since my vehicle has no transmission fluid dipstick. My driving condition would fall into "severe" category and it reached 60,000 miles now ...
View 10 Replies
CEL/OBDII code P0141 - O2 Sensor Heater Circuit Malfunction
So I just bought this car 64k well maintained but cant get rid of the check engine light. Replaced downstream O2 sensor with no luck. As soon as I get home I'll check voltage @ connector. Lets test the O2 sensor connection and test the pins to make sure there is no break in the wires.
View 17 Replies
