Lexus ES 2007-12 :: Check Engine Light Came On / Low Hissing Sound
Jun 10, 2013
Was driving back home and the check engine light came on, these are the codes I got:
P0345: Camshaft Position Sensor "A" Circuit (Bank 2)
P0365: Camshaft Position Sensor "B" Circuit (Bank 1)
P0390: Camshaft Position Sensor "B" Circuit
The car drove fine, didn't feel any power loss, I heard a very very low hissing sound but I honestly don't even know if it was always there or not... I did put some gas from a different station for once, so I doubt the fuel caused this?
View 11 Replies
Advertisement
My Lexus was working fine till yesterday, but today when I started (button press) it, it started giving me a Check VSC error and Check engine light along with Slip Indicator started showing up
Took it to Autozone for the codes and got
P0015
P0304
C1201
B2799
View 7 Replies
I have a 2007 XC90 3.2 RWD with around 112,800 miles.
On acceleration, there is a rattle (not a valve knocking) that gets quieter once a steady cruise is achieved. At idle in gear, a very quiet rattle can be heard. When transmission is slipped into neutral, the rattle goes away. The engine shifts normally, accelerates normally and gas mileage is steady at around 20.5 mpg (mixed city and highway). I am using 93 octane gas. This week the check engine light came on.
View 1 Replies
My wife just purchased a 2011 ES 350 w/20k miles from a off lease dealership on Monday. On Tuesday the check engine light came on. She quickly called the dealer. He told her that the check engine light coming on is very common. She has an appointment Tuesday morning to check it out. Would like to know if any other 2011 ES 350 owners have had the check engine light frequently come on.
View 12 Replies
For the past few months, I've had a weird intermittent check engine/VSC light problem. I've noticed that it comes after getting gas...and sometimes goes away after getting gas. I've jiggered the gas cap to be sure it's tight. Is it possible that this is something as simple as the seal in the cap gone bad?
View 4 Replies
2007 LS460L ... Check Engine, PCV, and VSC system light came up all of sudden. Traction control, cruise control and "Hold" system doesn't not work. I recently replaced Air filter, A/C filter and Oil change.
View 4 Replies
Check VSC and engine light on dashboard... I am confused what problem can be happened....
My car ES350 2008 ... NEW about 2000 miles ...
View 14 Replies
I have an '09 LS SWB AWD with 86k miles on it. A few days ago the check engine light came on with a message on the dash for me to check the VSC system. The next day the check engine light and VSC warning went away on their own. A day after that they came back on. I pulled the ODB codes and got the following:
P0012 - "A" Camshaft Position - Timing Over-Retarded Bank 1
I took it to my local Lexus dealership and they determined that my VVT-i motor assembly needed replacing. Total cost would be $1,222. Apparently this part regulate the camshaft for variable valve timing. I asked if I should notice a performance dropoff since it's related to valve timing but they said no. They said I wouldn't make it worse by driving it so I took my car back and they would order the part for me.
The next day the check engine light and VSC warning went away on their own again and have not come back on for 3 days now. I don't understand why the warning and check engine lights keep going off on their own if this motor assembly needs replacing. Once again it has been 3 days now and no lights have come on.
View 9 Replies
I am the proud owner of a 2008 LS600hl with 141,000 miles. The check engine light is now on permanently and the estimated repair charge from my lexus dealership is outrageously expensive. Here is the official diagnosis and recommendation.
"Code P1083 - HCAC Valve Stuck Open in Bank 2 .
Recommend Replacing Y- Pipe With HC Adsorber .
Possibly May Need Exhaust 2 Sensors.
View 8 Replies
I have 07 350 and my check engine light is on, i had it scanned and they told me that the code is BP0013 and bank 1 Cam position sensor is bad. What that code means and where is that sensor located???
View 9 Replies
Was cruising on the highway when the check engine light up. Scanned with a Techstream cable and got 2 codes: P0549 and P1083 (Engine and ETC). Just got a blown fuse yesterday, could it be related to a short ? Checked all fuses driver and passenger, didn't find another blown fuse (didn't checked in the trunk yet). LS600hl
View 14 Replies
2007 LS 460 - Check engine light came on one morning when pulling the car out from the garage. I plugged in my OBD data collector and received two fault codes: P1363 and P1365
Experienced these OBD codes? The printouts I received from the useful Lexus parts guy shows a cam position sensor fault code or VVT fault code. Need to change the sensors or wiring associated with them?
View 11 Replies
I have 2007 ES350. I was driving then check engine light and VSC popped on. I went to autozone then they said p0776 & P0746. The car is still driveable. I can still drive it on the expressway. The shifting from 1-3 isn't smooth. I'm going to take it to a transmission shop.
View 3 Replies
I was driving home and all of a sudden my rpms are at 3.5 4k rpm wont shift to next gear. I put in in tiptronic mode and shift it to 8 it works fine. Then about 10 minutes later check vsc shows on dash traction control light is on check engine light is on and the light next to the check engine i think it is the abs light. I havent pulled the code yet.
View 1 Replies
A few days ago my "Check VSC" warning came on along with the check engine and traction lights being on. I left my car in a parking garage for a week when I was on vacation and the lights came on once I started the car after getting back from my trip.
I have had the "Check VSC" warning before and I fixed it by replacing my gas cap. My gas cap seems fine this time around so I got my codes scanned and the only one that came up was P0300. Having this issue with the 2007 Lexus GS 350? I still feel like it's my gas cap because I bought a cheap replacement last time around.
View 8 Replies
I have owned 2 SC and I notice both of the SC I have owned get a odd " hissing " sound, when the ignition is turned to the " On" position with the key located in the engine area, It will come on and then go off ...
Sometimes this " hissing " sound will come back on when driving and then off again ...
Hissing sound when the key is turned only to the "on" position?
View 14 Replies
My car has been making a hissing sound when I turn it off for the past few weeks, I checked the hoses around the intake manifold and they all look to be attached fine.
I took a video and discovered a flex in the rear of my manifold..is this normal? What would be the common issue?
Look at the rear of the barcode label
[URL] ....
View 8 Replies
Experience a hissing sound from stereo, specifically mark levinson. The hissing sounds occur from certain songs and when the engineer rpms are around 4500.
View 1 Replies
I ran over a chunk of ice at about 15mph. I could definitely hear it scraping the undercarriage. Now, when the engine is on (regardless of RPM), there's a hissing sound (like air escaping, or a belt sliding against something) coming from the back right side of the undercarriage. What I damaged? No smoke, no leaks... just the hissing sound.
View 15 Replies
I replaced rear pads with akebomo and installed centric premium rotors but in the morning I hear a very loud noise (as loud as as a steam locomotive :-) for the first few times I press on the brake, then the sound goes away. After that, no hissing sound all day until next morning.
I used a brake silencer spray on the back of the pads but to no avail. I had the mechanic lube the pins twice but in vain. Noise went away for 3 days and came back.
I was told to go with OEM pads with shim. I was wondering if this the correct solution and where is the best place to get those OEM pads?
View 6 Replies
I have the '03 Lincoln Aviator 4.6 DOHC. It has a noticeable knock/ping/chatter and somewhat sluggish acceleration. I notice the PCV hose was collapsed and shredded. I replaced the hose and valve, didn't change idle or acceleration and I still hear the hissing noise in the same region. I unplugged the EGR valve and started the truck, the idle was the same as before I unplugged the valve. could a bad EGR valve give a vacuum leak that is hard to detect? I tried testing for leaks by squirting starter fluid near the suspect areas, and I couldn't detect anything.
could a bad PCV valve be caused by a bad EGR valve and/or vise versa?
View 2 Replies
