LS / MKZ :: 2002 Lincoln Idles Rough On Cold Mornings But Runs Fine
Jan 6, 2016
The car idles rough on cold mornings but runs fine. It will stall while idling but starts back easily. I am getting a 1131 and a 1151 code with my scanner along with 0300 and lean bank 1 codes. I started having these problems after I had to remove the upper intake to replace coil packs. I was getting egr code and had an egr port completely block off but cleaned that out and no longer get the egr codes. Spraying carb cleaner around the engine I get a very slight bump in rpm around a couple of the intake ports could that be my problem or should I look deeper?
View 5 Replies
Advertisement
I have a 1999 Ford Escort SE wagon with 112k miles on it. Last week when leaving work my car started very rough. This was unusual so I killed and restarted the car about three times before letting it run it's course (~30 seconds), after which the car ran fine. About a week later on my way to work the car seemed to 'sputter' (for lack of a better word) when I pushed down on the petal looking for some power on two separate occasions. On each side of the sputters the car seemed to respond fine, but when it did sputter there was a severe lack of power. I got to and from work just fine, but while letting the car idle in the parking spot of my apartment for a minute before shutting off the engine the check engine light finally came on. The following morning the car again started rough (as if it were misfiring/running on 3 of 4 cylinders) and this time it took a good minute before smoothing out. However, after the car smoothed out I experienced no issues on the way to work, no sputtering, no loss of power, nothing. Doing some initial online research I feel that the problem may be one (or more) of the following:
-Fuel pump
-Vacuum lines
-O2 Sensor
-Spark plugs (they are original)
-Fuel Filter (it is actually past due for replacement)
I plan on getting this checked out ASAP, but that still may be 2ish weeks away with my schedule. Some similar reports say that I may be having a 'lean mixture' issue (not getting enough fuel), but I haven't had the time to check the code. My question is, how "safe" is it to continue driving my car with the current situation? Is it at a super high risk of failure/random stalling during rush hour? Will it cause any damage to the engine if there is a cylinder misfire upon start up? I was also wondering if the car would be reasonably reliable to drive on a ~400 mile road trip on an upcoming weekend, but I am making plans as if it is not.
Additional Details:-Tried charging the fuel lines (car to 'ON' then 'OFF' position 3-4 times), had no effect on the morning start-up-Commute to/from work is about 20 miles
View 13 Replies
2000 F350. Starts great. Idles fine. After it warms up a little, it will run rough and lose power like it is only hitting on a few cylinders. It will eventually stall unless I push the clutch in and bring it back to idle and then it smooths back out. I figured it was starving for fuel but I can rev it with the clutch in with no issue. I ran it up to 2500 rpm and held it there with the clutch in and ran perfect.
I let the clutch out and start rolling....missing again. The check engine light does come on but my scanner says that there are no codes stored. If I idle it, it will smooth out, and the light goes off. All I have done so far was change the fuel filter which was almost plugged shut and the housing was full of rust looking debris which I cleaned out. BINGO! Nope. Same issue.
I am really at a loss as to where to start. I bought this with 120k on it and it now has 170k and I have not had to do anything other than routine maintenance.
View 14 Replies
I recently replaced the plugs cuz I had a rough idle all the time. During plug change when I discovered they had already been changed I found one that had a burned off electrode. Does this mean a lean condition exists?
After plug change it runs smoothly but only after 10 min warmup in our canadian winters. I can drive it when its not warm but seems to have less than full power and idles very badly after driving w/o proper warmup.
Next I changed fuel filter and checked fpdm, it was a little rusty but not bad so i just mounted it 1/4 off steel to prevent further rusting.
Since then I have installed a programmer [diablosport] but found no codes since i had battery disconnected for filter change. no new codes in last few weeks since.
So do I have a lean running cylinder causing this poor cold idle or a rich cylinder? It must be a clogged or dripping fuel injector right?
View 2 Replies
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 Replies
I used a OBD scan tool and all it told me was my idle air control system rpm is lower than expected and my evaporative system has a high purge flow. What this means, can I fix it or do I have to send it to a shop. Also when idling the short term fuel trim 1 is at -3% whatever that means.
View 16 Replies
This problem has been getting worse over the last 2 years. When the car starts it idles fine at about 1000 RPM. As soon as it warms up, it starts to idle rough, between 500 and 750 RPM. It almost quits running. As soon as you give the car some gas it runs just fine. About 3 weeks ago I got a "Engine Lean" check engine light error. I reset the system and have not gotten the error again. Since then I have: changed the MAF cleaned the EGR (made sure it closes completely and ohm out the coils in the actuator) changed the O2 meter on the exhaust manifold cleaned out the throttle body Ohmed out the air idle controller. What I should check next. I was planning to check the fuel pressure in case it is a fuel system problem. It is a 1999 ....
View 5 Replies
My 2004 Lincoln navigator is very rough at idle but runs smooth when I give it gas. Someone said my VCT may be stuck or bad. I looked at Youtube videos of VCT replacement but in all the videos the VCT's are up front in the valve covers. On the Navigator they aren't there. Where the heck they might be located?
View 2 Replies
I have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
View 9 Replies
My 02 navigator does not idle right when in park or sitting at stoplight. I've gotten codes po171 and po174. The truck ran fine for a good 3 months after the (service engine soon light) came on and I got these codes so I decided to do nothing.. Now it idles bad and has even shut off twice on me while pulling into driveway. I changed the MAF and that did nothing.. Should I assume its the o2 sensors or is there a chance my CAT is shot.
View 2 Replies
Just recently my Prius Taxi with 340,000+Km has developed a little problem,it starts fine but after 20-30 seconds it begins to feel like it's not running properly on all four cylinders,if i go to the exhaust pipe it seems like it's spluttering slightly.
Yesterday I changed the plugs,checked air filter and all connections,everything fine, when I accelerate it feels hesitant but after the car gets up to temp it seems to go away,it only happens when i start it first thing or if it's been left for a few hours, it's never had the throttle body cleaned and I'm wondering if what I'm describing is a symptom of this?
View 19 Replies
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 Replies
Have a 2001 Civic DX, Manual Transmission, 228K miles. 1.7L SOHC.
Recently changed front motor mount and timing belt on the same day.
I noticed the car running rough and is only rough at certain RPM. Here are the rpm ranges it runs rough, 700rpm which is idle, 2200-2400rpm and 3400rpm approximately. It idles at 700rpm which I believe is the idle rpm on my car, so thinking my timing is not off. One more thing I noticed is if I have AC on and reving down in rpm it sounds like it is about to shutoff (never shuts off) and get a stronger vibration and same thing when I turn the AC on at idle. With ac on my rpm are 720rpm give and take a few. I been driving with above symptom for 300mi+ so far, even got it upto 95mph, don't know if it is an indication of anything. Got new spark plugs installed at 220K miles.
Could it be the motor mount or my harmonic balancer is out of balance. I did have to use 3/4" impact wrench to knock the harmonic balancer bolt loose. It is a little rusty given I got 228K miles on it.
I am just dreading the thought of my timing being off by a tooth, me and my friend checked the timing marks per oem manual, he checked the cam shaft pulley marks and I did the crankshaft. When we installed the timing belt I only turned the engine counter clockwise so I would not cause a problem with timing belt slack. My AC belt may be a little too tight as well.
The motor mount I put in was an aftermarket one that I bought from amazon. But I have put in aftermarket mount before on the same car and never had anything like this. I am planning to loosen the motor mount, shake the engine, tighten them back up and see if it makes a difference. May be the engine is not seated properly.
View 13 Replies
My 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 Replies
2001 VR6 GTI....
Already done:
Replaced the coil pack and plugs
Measured resistance of plug wires (all at about 6K Ohm)
Replaced front O2 sensor
Replaced purge solenoid valve
Replaced coolant temp sensor
Replaced fuel filter
Replaced fuel pressure regulator
Replaced MAF sensor
Cleaned the throttle body
Cleaned the throttle position sensor
Ran a tank of seafoam treatment (injectors were new 6 mos ago.)
Checked running voltage of battery
It was smoking and stinking bad with a rich mixture. It improved with the MAF change but still runs like a farm tractor. Now it idles on 3 or 4 cylinders, runs rough through 3000 RPM then runs cleaner at above 3000 RPM, but only at light throttle. CEL is either on or flashing when driving.
Don't know what to do next - nice car not fun to drive like this. What this could be and how to test it?
View 7 Replies
1995 Mazda Protege1.5 LAuto153K miles.
My car was running fine, then one day it started sputtering while driving, mostly when I accelerated. It stalled and I could not get it started. This happened on a day when it was raining hard, but not sure that had anything to do with it. A few days later when I went to pick the car up it started right up, it had stopped raining and been dry for 2 days prior. But about a mile into the drive back home it stalled and I could not get it started.
Here is what I have tested so far.
- Put in new fuel filter.
- Tested the fuel pressure and pressure regulator
- Tested the injectors with a noid light.
- Tested that the spark plugs were producing a spark.
After I pulled the plugs and cleaned and dried them (they were wet with gas) the car started, but I think not because of anything really related to the plugs. What I've noticed is that when cranking the engine if I give it gas it will not start but if I keep off the throttle it will reluctantly start. But once it starts the idle is smooth and as it should be. Then if I give it any gas it immediately stalls. It seems to me given these symptoms that it is getting enough air to idle but not enough air to match the increased gas.
The only CEL code that I'm getting (which I had before this issue occurred) is the "closed throttle position switch" (I forget the number). If it was an MAF, or IAC, or EGR issue would I not get a code? What this could be and how to test it. Again my guess is its an air intake issue but not sure where.
View 11 Replies
96 civic 120K miles, stock, automatic.
In March I was running low on fuel, maybe 1 gallon left in the tank. It took a few cranks and on the last try i gave it a little gas and it started, albeit very rocky for about 1 minute of driving, filled up immediately and 2 freeway miles later, no real issues. I live in LA so very low ambient temperature is not a problem.
April through May, starting was a little rocky, it was inconsistently rocky too, sometimes there was no problem. Usually it's weak, stuttering, sometimes just cranking but I seem to get it to start. I stopped giving the pedal gas because I read that's bad (I own a vintage bike, so it's news to me). I don't drive that far and figured I'd try some Seafoam and some freeway miles would clean out any debris. Worked for that tank a bit for the next tank before the problem came back.
Still getting the rough starts, but now when I give the car gas as I pull out sometimes it doesn't accelerate for 15-30 seconds, maybe 25 yards then it drive like normal. No dying at all but getting worse with starting up.
I've tried turning the key (not turning the engine over) 5 times and cranking on the 6th and it seems to work. I thought maybe it's the fuel pump or fuel filter but read it could be an ignition coil/ spark plug/ spark plug wire issue. Two different ball games.
My MPG is not really droppingI had a new fuel filter put in in February as routine maintenance (thing was on so tight had to bring it to a shop so no rookie mistakes there). Timing belt &water pump replaced 6,000 miles ago
View 3 Replies
Ok, I have owned my 02 Passat with the 30V 2.8L V6 since may. I got it with 115K and now its just under 129K I had the timing belt done at Jimmy's in Provo UT at 126K and up until then the engine ran great. Since the belt was replaced <along with the water pump and such> . The car has a tendency to feel like its idling rough, and when you start it up first thing on a cold morning it sounds like the valves are rattling. It does this for a brief second then goes away until the next time you start it in the cold morning. It wont do this if its warm outside, or after you start it previously that day. So far I have replaced the plugs with Bosch Platinum 2 prong plugs, and replaced the fuel pump. I replaced the fuel pump when it dead on me without warning about 2 months ago.
View 1 Replies
Just as the title says, 214k great shape just wont get going more you mash the less it goes.... fuel pump already replaced, can undo battery and take a while to reset feels to do fine then goes back to bogging down... TPS ? idle air control?
View 3 Replies
So I have a 95 aerostar 3.0. I use it every day my a delivery vehicle. I keep it maintained. About a month that ago, it developed a skip or a hesitation, most!y at high speeds, usually under load. I thought it may be transmission but had it checked and was ok. I drove it like that for several weeks. Then got worse so I parked it for ten days until my mechanic was available. When I cranked it to drive it over, it spit and sputtered the whole way here and barely made it. It had never done that before. He changed plugs and wires and distributor cap, even though it had been less than a year since all that had been done. Still no change. Driving way worse after sitting for ten days.
View 6 Replies
So my "farm truck" is idling very rough, to the point that sometimes that it stalls out. At high idle it runs fine but when its at a idle its very rough. Its been running fine until probably a month ago or so and its just getting worse. What it could be? I am thinking it might be that something is dirty but i just dont know where to start with figuring out what the problem is.
View 9 Replies
