LS / MKZ :: 2000 LS 3.9 V8 - Started Idling Rough / Code P0171
Jun 24, 2012
I have a 2000 Ls 3.9 V8 125,000 miles that started idling rough.I checked for codes and got p0171 (bank 1 lean), p0175 (bank 2 rich) and p0307(cylinder 7 misfire). I swapped cop and sparkplug from cylinder 7 to cylinder 5 and erased the codes.I ran the engine for a while and rechecked the codes to see if the misfire followed the cop and plug. They did not. I still get p0171,p0175 and p0307 (cylinder 7 misfire).
View 7 Replies
Advertisement
My daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
View 6 Replies
It's been a long time since I have posted here mainly because my truck was wearing a bow tie for awhile. But my wife was nice enough to tell me the Bow Tie wearing truck was making a funny noise on New Years Day (seems a small drum corps took up residence in the oil pan). So anyhow now I am back in a real truck . My new to me 1998 F150 5.4 Liter ran fine until yesterday. It started idling rough and almost stalling at red lights. about halfway home the CEL light came on and is throwing a P0171 code.
So far I have checked for vacuum leaks including all the elbows on the PCV system' tried the spray test with a can of flammable break fluid and a can of starting fluid (man I love the smell of that stuff) could not find a leak. Cleaned the MAF sensor and the K&N air filter (not a fan of these) IAC seems to be working. Only thing I know that is leaking for sure is the driver side exhaust after the cat. But that is the wrong bank if I am correct on which bank is which.
So why only one bank running lean and why does it act like it is only firing on 4 cylinders?
View 14 Replies
I have 2007 explorer with the 4.6 V8....
Recently it started running horrible. Rough idle, drives badly, hesitation, etc. Check engine light is on, code P0171. I cannot find a vacuum leak, and i am pretty much at a loss. Before it started running poorly i replaced the thermostat, and flushed the coolant. I am assuming this is a coincidence.
View 1 Replies
I have a 2000 f150 with 5.4 Triton with 165k miles. I did invest in a code reader. It started missing and code P0302 came up along with P0171. Put new coil on #2 and truck ran fine for a few days. Then it started to run rough again. Shaking, Idle rough, no power and CEL came on again. This time code P0171. I changed out fuel filter to no avail. My next step was to start looking for vacuum leaks. As I'm searching, All I am finding is trucks with this problem also get P0174 code. My question is since I am only getting lean on one bank does that pretty much eliminate things like MAF or the famous elbow vacuum leak and make something that only affects one bank like an O2 sensor on CAT more likely?
View 2 Replies
I've got a 2000 f150 with a 5.4 and 135,000 miles. The other day it was driving fine then i stopped and got gas and after that it was boggy and running rough so i thought bad gas but i ran through that gas and got more at a different store. The cel came on i got it checked it was misfire cylinder 1 so i put new cop, spark plug, and injector. Unhooked the battery and then the light came back on so i ran the code and now im getting a p0171. I checked the pcv and sprayed around the intake and vacuum lines. I also checked the pcv hose and elbow in the back and i found nothing its a fairly new hose. So, it does run rough it shutters a lot.
View 2 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
97 F150 4.6 Vin 6, 5-Speed Trans, 200,000mi, Rebuilt recently. I was on my way to get my truck smogged, but she threw a code, P0171. I read somewhere to clean the throttle body elbow, which I did (needed to do it anyway). After I had everything put back together, I start her, and it's rough and immediately dies. If I keep the RPM's at about 1.5k for a minute, then let off, the truck will run fine for about 30-45 seconds, then die again. I just replaced my IAC and the problem persists.
View 8 Replies
I have a 2006 Ford Ranger with the 3.0L v6. The check engine light came on and the code it is blowing is a P0171. It runs rough at idle or when I let off the accelerator and "fine" at speed.
The code told me to check/clean the MAF which I have done. Next on the list that I saw was the PCV valve. I disconnected the electrical to it and then disconnected the hose. Some oil poured out of it... not a lot but some... The valve still seems free, it clicks when I rotate/shake it and I can blow through it (I know, highly scientific). I can replace this (if I can find it, Napa and Advanced Auto don't have a part that looks like it...) but I'm wondering what else could be wrong.
View 1 Replies
I just started to have this problem yesterday. Engine light comes on and stays on. Engine shakes and truck won't go over 50 MPH. Autozone code checker came up with P0171.
Truck has about 95K miles and I had the spark plugs replaced at 75K miles.
Transmission was rebuilt at around that time also.
I only drove it to Autozone and back today to post the code and see what everyone's opinion is as to what's wrong.
Here's what the printout says : P0171 "Fuel Trim Bank One Condition"
View 6 Replies
Mazda CX-7 sport that has rough idling when it is started and goes away when warmed up or driven. Is giving OBDII error code P0300 - multiple misfires. Where should I start looking?
View 3 Replies
First owner, 192000 miles. Check engine light came on during last winter, I put fuel injector cleaner with gas and it went away for a while. It came back on, if i reset, I can drive for about 50 miles before it comes back on line. Also, may be two or three times a week, when moving after a stop, the vehicle stalls, i have to take the feet of the gas pedal and give gas again.
I called up the dealer asking for fuel filter and fuel injector parts prices. Fuel filter is in the gas tank and not meant to be replaced. The fuel injector I was told 4 x $155 each. For diagnostics they need $100
See attached, I was able to clean sensor 1. I could not unscrew sensor 2, the screw is rusted, plus there is no room to get a longer screw driver and turn.
View 14 Replies
2000... I have a code P0171 bank 1 too lean. My question is does this exclude anything that will effect both banks? If it was MAF sensor or fuel filter would it set code and say banks 1 and 2 running too lean? In which MAF sensor ohms out correctly. I cannot view fuel trim files. I have looked for a vacuum leak with no luck. I got some cigars to try to smoke it to see if there is any vacuum leaks. Trying to narrowing what i need to checks.
View 19 Replies
My wife stopped for gas at a Circle K, about two days later this Sienna started idling rough and missing. I put some Seafoam in it and it cleared up. About one week later, she gets gas again, at another Circle k,about two blocks from the other one. Again, the next day she comes home from work complaining of the van running rough. I took it out and it drove fine. Whenever this happens the Check Engine light comes on, so I ran a code reader on it and it tells me, "Miss detected on cylinder 3".
So I checked all the plug wires, took out the plug (which I had just changed back in Oct.) and checked it, it looked fine. I thought maybe it could be the coil, so I switched the coil to see if I got the same code reading on a different cylinder. I unhooked the battery to clear the code after switching the coils, started it up and still got the rough idle and code. I turned it off (the van) and go in the house, I come back out and start it and it's running fine. I go to the store and all is well, go inside the store for maybe 45 minutes, come back out and start it up, I get the rough idle and missing.
I ran the code reader on it again and cleared the code, then restarted it and it was running fine again. Whatever it is, it has something to do with starting the engine (a 3.1L). One time it will start up and drive fine, the next time it starts the rough idling and missing. I figured if it was the coil and I switched them and got the same code on a different cylinder I'd narrow it down, but so far it has been running normally.
View 8 Replies
1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
View 2 Replies
So I bought my accent used a couple months ago. It is a 2007 SE 3dr 5spd manual. It ran nice during my test drive and the price was right so I bought it.
Now I'm wondering if there is any way to find out the service history on the car...at least the major one's (30k, 60k)?
I ask because recently the engine was idling a little rough and it threw a P0302 code so I changed the spark plugs and holy-cruddy-deposits-batman those things were black. Gapped the new ones and popped them in and its a noticeable difference. My CEL keeps coming on and throwing a P0496 code as well, virtually once every tank of gas. Its not the gas cap so my next step there is to check the PCSV and hoses.
With these little problems, it makes me wonder about any larger issues. I know the timing belt on these things is supposed to be replaced at 60k. Additionally I would be willing to bet that my ECM software is out of date. Would Hyundai have records for any of the big maintenance milestones since they are required for warranty work?
How much does it cost to have a dealer check your ECM software and update it if needed?
View 3 Replies
My 2000 Mercedes C230 Kompressor's been riding rough, particularly at low speeds and when idling. I took it in to see if engine mounts needed replacement, and yes they do, but my mechanic also found that I've blown or cracked the head gasket. Coolant has solidified around the gasket, keeping it from leaking now, but he indicated that with the next rain, that solidified coolant would be washed away and the car wouldn't be able to hold coolant. The car has 160,000 miles, recent brakes and tune up (should he have seen the gasket problem at tune up???).
View 9 Replies
Finally back able to start working on the Ranger and have a few questions.
When I got this thing back from my son it was running rough. I've fixed all the codes it was getting so no luck there now. Not sure how to explain it but, it feels like it is cutting back when driving at a steady speed and it idles rough. Not really like a miss but more like a hesitation when driving.
I've cleaned the MAP and IAC and changed the fuel filter. I also pulled the plugs and they looked good. My son installed new plugs and wires but he used the E3's and not sure how, or if, you're suppose to set the gap. I haven't checked the PCV yet because haven't figured out how exactly you get it out without pulling the intake.
So, where to look next? I'm kind of thinking the cam sensor but think I'll leave that to a shop sense I want the shaft replaced at the same time.
View 2 Replies
Nissan altima gle (2000) and for the past 3 weeks it has not gone over 55. The car was running ok before but was idling rough. A mechanic replaced the intake manifold gasket, the MAF sensor and the fan sensor. I decided to change my spark plugs when I noticed the idling was getting worse. The spark plugs had oil on them and now a month after the new ones are burned (like ashy tip, black thread) and dripping oil again. I think is the oil not letting my car accelerate in the highway. I considered changing the valve gasket, cables and cap for the spark plug. A mechanic told me not to bother because the motor is a lost. Is he right?
View 16 Replies
2005 5.4l... Its giving me a code p0506 rpm to low idle air control system called for new one they said my truck don't have one said only up to 04 so what now truck idles rough n when u step on it it misses so bad its not funny feels like its laying over...
View 3 Replies
I own a 2001 Accent 1.6, auto. 150,000 well-taken-care-of miles. New plugs/wires/timing belt/coolant flush 10,000 miles ago. Most recent oil change was with Shell Rotella T5 (I believe 10w-30 blend) and Purolator PureOne filter, 4-5,000 miles ago. It does not burn any oil, and runs very well. It has never been low on oil, revved high, or abused in the 10,000 miles I've owned it (except an ebrake u-turn on a dirt road to scare the wife )
The engine has always had a mild tick when cold, that goes away within about 30 seconds. Normal, from what I could tell. Also, it has always had a tick from roughly 1500-idle when releasing the gas, in neutral. Again, seems fairly normal for a little engine, I figured just some valve noise.
This morning I started the car (sat overnight) and it idled a bit rough for about 20 seconds, and I noticed that the ticking from before was now closer to a knocking/tapping, nowhere NEAR the horribleness of a spun rod on my WRX . But it was still a bit alarming. It never really quieted down, but as I rev, the sound goes away completely above 2k, and the flutter when I release the throttle is louder than before.
View 11 Replies
