My car had slowed down when I pushed the gas pedal. I had to get towed. White powder was on the face of engine. Car will not crank. It makes a humming sound. Kia 2004 spectra ex....
View 8 RepliesIs it normal on the 2.0T that when you are driving and stop at a red light to get vibration that you can feel in the car and hear in the motor? As soon as you let off the break it stops and the engine stops the noise. I don't drive the car enough really (my wifes) to know if it is normal or if this just started. It is an 07 and just turned 12k on the weekend trip. Also, having a problem on Sat radio with there being a high pitch hum in the back ground? [IMG] [URL] ...
View 13 RepliesI have a 2008 Prius. Had to do an 'emergency' stop. Put my foot on the brake pedal REAL hard and the car slowed way down, but not down enough. Munched the front end. Now remembering back, I didn't feel any 'chattering' from the ABS brakes. It seems like I got regen braking but never switched to the hydraulic brakes. Is that possible? Did I experience a braking failure? Or do Prius just take a lot longer to stop? I did a test stop in the rental car I have now (not a Prius or hybrid), and it gives me the ABS chatter as I would expect, with a short stopping distance.
View 5 Replies1090 Lumina Sedan 3.1 ... First time it had starting issues Recently. About 2 months ago my lumina's engine would die when i pushed down on the gas pedal. After 2 days of trying to fix the issue it wouldn't start at all, i replaced:
TPS
MAP/MAT Sensor
Fuel Filter
None of these worked so i sent it to a shop, they replaced:
ECM
Multi Port Injection (All 6 Injectors)
TPS (even though i had just installed a new one)
Serpentine Belt (it broke when they were test driving it after the Repairs were done)
The car would not start even after they replaced the first 3 parts on the list, so the tech looked further at the engine and found frayed and open wires, on the bottom near the front side passenger door, he repaired these wires and the car started and ran.
The only issues i had after their repair was a rough idle while braking and/or when i was at a full stop, the rough idle went away after a few days of driving.
((Current No Start Issues))A week ago i had what i am guessing is a few electrical issues: Speedometer Twitching and then dropping to nothing while driving, temp and oil light popping on and then off, when the engine was at a good temp and the oil was fine when i had checked the day before.
I went out a few days ago to run some errands and on my way home i turned a corner and when i put my foot down on the gas pedal the car just went "Put-put Put-put" every time i pushed the pedal more than a 1/4 of the way down. i reach a stop sign and being i was in the middle of nowhere and no one was coming down the road for miles i braked slightly and went past the stop sign halfway through my turn the engine died and i coasted to the side of the road, i got out and checked the engine, i had coolant not a whole lot but enough, then i checked the oil and it as far as i could tell it was at the add line even though it had been fine a few days before,(there has been no indication of an oil leak).
I rechecked the coolant and it looked like there was more in there than there was a few minutes before but i couldn't be sure, i was able to get the car restarted and headed towards home (about 2 miles away).at this point i was able to get the car going at around 25-45mph on the next sharp corner i turned the engine died again so i restarted and kept going, it died once more right before i reached the driveway but i was able to coast the rest of the way, once i parked the car i turned the engine off and tried to restart it a minute later and it started again so i left it be and called someone to bring me some oil, when they got to me with the oil i put some in and and it would not start at all.
- I checked one of the spark plug wires and it is not getting any spark.
- The ground terminal on the battery seems to be stripped
- The battery / altenator / starter---- All read to be between 12.15 and 12.36 volts
- The head lights, instrument panel and such still turn on properly.
I'm at a loss here, it was just in the shop 20 days ago and now it isn't working again. I would prefer to not have to put it back in the shop, if it might be something i could repair from home.
Experienced a chatter in the clutch pedal with the a/c on when clutch pedal is pushed in. To me it feels like the throw bearing isn't disengaging the clutch fully, plus my clutch is kind of high once full disengage unless its normal.
View 5 RepliesMy clutch has been feeling very strange lately, and has had a mind of its own. I have looked underneath myself, and have even taken it in to two transmission speacialists and they can't figure it out. The master cylinder isn't leaking, and the slave cylinder is fine as well.
Here's what is going on with my clutch...
- I will push in the pedal, and there will be ZERO resistance until about 1 inch from hitting the floor, then all the pressure is there, and I am able to shift. However, sometimes I won't even be able to put it into gear because the clutch won't engage.
- Then I will pump the pedal, and slowly I will gain a little more room on the draw of the clutch, and it will feel fine. All the way to the point where a few days later it will be driving like new.
- Then it will start feeling funky again a few days later and the cycle starts over.
I drive a 2003 GTI 20th AE.
I traded my 2007 Prius for the 2010 III Prius on 5/30. I had 5 wonderful days with it and on the 6th day, it started.
There is a loud creaking noise when the brake pedal is pushed and released.
The dealership contacted Toyota and did everything that was suggested to correct the problem and no luck.
My less than 7000 miles RX started making noise when I pushed the brake pedal. Evidently it sounded like the "LS brake squawk" according to service foreman. Not sure if the actuator is same in all RXs.
View 3 RepliesMy transmission died last night on the way home from school. I was driving down the road just after leaving school and as I started to accelerate the car, I noticed that it wasn't moving so I pushed the pedal a little harder when I saw the rpm gauge rev. Up pretty high. The car was showing it was in 4 th gear and as I was slowing down so was the number on the display. I came to a stop and tried to move forward but noting. I had the car towed to the dealership so now the fun begins to see what is wrong with it.
I had the car in a few months ago for a whining sound coming from the car especially when I would put the car in reverse to back up. The dealer said we don't see anything wrong, go figure.
I'm suspecting that the transmission is shot. When the car was towed to the dealer I had to engage the parking break because the car wouldn't stay parked, it would roll even though it was in park.
My girlfriends Toyota Echo has been giving her problems it seems. She says that it will randomly not respond to the pedal being pushed. She's not great with cars, but says she doesn't hear it revving. I was thinking dirty fuel filter, but I would think it would be running rough all the time if it was clogged? What it could be?
View 3 RepliesJust got into my 2006 Sonata V6 this morning. 120,000 miles. Drove last night, no problems. Started her up now this morning, noted check engine light and ESC lights on.
Pushed accelator pedal, no increase in RPMS at all. Put the car in gear (auto), car moves forward and backward, but pressing the pedal doesn't increase the rpms at all, so right now its not driveable. Luckily, its in the driveway so I know it could be worse. Took floor mat out, no interference issue there.
I changed the starter solenoid and that was over 45,000 miles ago. Never had that problem.
So a few days ago the family and I were on a road trip. After driving for close to three hours we ran into a problem. We were doing about 75, which is about 3000 rpms with the 4.6L, When we dropped from 3k to about 400 and started to lose speed. I pushed the gas peddle all the way to the floor and no response at all. I pulled over and it had a very rough and choppy idle and it wanted to die. It eventually did. I checked all fuses with nothing found and i even hit the fuel pump shutoff reset. It started back up no problem and we got about 5 miles before it the exact same thing. Idle at about 400 rpms and no throttle response at all.
I shut it off and called a tow truck. It started up and they drove it onto the back of the tow truck and off at the local mechanic. They spent 2 whole days trying to diagnose it and even drove it for 4 hours straight, no issues. They pressure checked every system they could and tested every sensor they could. They could not find a single thing wrong with it. I drove it home 3 hours away with no issues. I got home and let it sit for about 10 minutes before I had to leave. I didn't make it more than 2 miles before the same issue popped up. I pulled over. Shut it off for 15 minutes and it started right up and drove home.
It threw 4 codes.
1. Pressure control solenoid malfunction
2. Fuel pump Primary circuit malfunction
3. Gear 3 ratio incorrect
4. Gear 4 Ratio incorrect
I've had 2 mechanics tell me its a PCM issue.
I have a 2007 Tacoma 4 cylinder 5 speed. The clutch pedal started sticking about a month ago and has only happened a hand full of times. When the pedal is pushed to the floor it would stick, I thought it was hanging up on the floor mat at first but that was not the case. I went out to move the truck today and the pedal immediately stuck to the floor. Like usual I tapped the pedal kind of on the side to get it to release. the pedal then came back up. But now it wont push back in at all!!! There is only 1/2" of travel on the pedal and stops solid. It's like it is binding up on something. The spring seems to be in place the right way and nothing that I can see obviously wrong.
View 4 RepliesI noticed this strange behavior this afternoon on my SantaFe DM. Every time I press the break pedal, the front position lights turn on during daylight. Light switch is set on Auto.
View 2 RepliesLately, when first starting my car and after it’s been sitting for a while the gas pedal seems to be stuck.
When I push on it slightly it doesn’t move; but if I push a little harder it will make a noise and become free and movable. No further problems until it sits for a while or the next morning. Then the same stuck pedal. Exert a little pressure and it frees up.
I tried squirting WD40 on the linkage but it does no good. What could cause it to bind up? 2001 Mazda Protege LX 2.0 ....
Let me tell you a story ‘bout my daughter’s 2008 Chrysler Sebring 2.4L…
We have owned the car since 2009. Recently the car has begun to start intermittently. Generally it starts normally. Other times it won’t. It can be driven for a month with no problem and then BAM! It won’t start. No dead battery sound, no clicking, no starter trying to engage NUTT’N!
AND… the brake pedal is firm! The brake pedal is firm and cannot be pushed down!
The car has been to the Dodge dealer several times. They have replaced the starter because a couple of teeth were missing, flashed the computer and replaced the alternator. The car started fine for a few days and then wouldn’t start again.
The Dodge boys kept the car for a week and of course, it started fine while they had it. One of the service managers told me to pull out a certain fuse to reset the computer. They also told me that they usually see these types of problems if the car was jump started wrong (the jumper cables were hooked up backwards I guess).
1988 Acura Legend, 2.7L 6 cyl., 181,000 miles only do 6,500 miles a year to train station, parked inside, runs great. Last week parked out in hot sun, '90s, for 8 hours. At first, no problem. When did errand and returned to car, pushed clutch pedal and it would not return or allow gear to engage. "Jammed" into 1st, then could not shift, shifted slightly by pulling up on clutch pedal with my foot. Parked overnight, cool, next morning seemed to be fine and crept to mechanic. Mechanic road tested and found no problem and now seems to be working okay. Would parking in sun, high heat cause "clutch cylinder" to "seize" or "freeze"? Is there a "fix"? Also, increasingly hard to get parts for this car.
View 6 RepliesA few weeks back just after buying a new front hub assembly (so I know I have Live Axle 4x4 and 4WABS), a dude on an excavator pulled out in front of me on a blind curve on an interstate exit ramp. Almost got him, then almost got got by the car behind. The hard stop caused a rear line to blow.
When I got home, fluid was still coming out when I pushed the pedal, so the first thing I did was top off the reservoir. I was surprised it was not empty.
I finally got lines that would fit, and replaced both sides. Fast forward a few weeks and I had time to bleed the system. I hooked my vacuum pump to the right-rear wheel cylinder port, opened it and began to pump. Pump, pump, pump, and still no fluid. Tried a few times. Left the pump on, opened the port, (charged the battery), started the truck and pumped the pedal - no fluid. Also, the fluid level did not change in the master.
Master cylinder bleed? Do I need to have the ABS motor bled?
I drive a 2009 Kia Spectra. Mileage - 89,000. About a year ago, very infrequently, I started noticing that the engine would start racing when I would try to come to a stop. Now, almost every time I start the car, the engine is racing while it is still in park. And when I come to a stop sign or stoplight, the engine races when I put on the brakes. This is NOT an issue with the mat hitting the accelerator. Lately, also, the car is starting to die for no reason when I bring it to a stop. I took this in to a mechanic, they could not find a problem--they cleaned off some cables but the engine was racing when I turned it on to drive home.
View 5 RepliesI have a 2006 Kia Spectra with 74K miles. It was apparently neglected before I bought it (at 55K miles), and has a case of engine sludge. It's clogging my oil control valve, and a couple engine flushes (by Kia dealer) over the last year have failed to correct the problem thus far. The car runs ok, but cannot pass an emissions test due to the check engine light and corresponding codes. Can I perform the flushes myself? What product should I use? Can I safely remove and clean the OCV myself? What product should I use?
View 19 RepliesFirst off, I would like to say that I really like how the engine rolls in my 06 Passat 2.0T. Suspension is great and the brake works well...so far. What worries me now is the persistent white noise I get in the cabin when the engine is on, driving or idling, EXCEPT when applying brake.
I took it to the dealer 2 times for this reason. The first time, the rep swore that he could not hear the sound and made a crazy person out of me. The tech wrote in the report that there is no problem. The rep explained that it is the sould of air circulating back (what air?).
So, I took it to an independent mechanic, the one I have been taking my other cars to (Nissan, Infinity, BMW) for the past 5 years or so. He readily heard the sound and identified it as vacuum leak.
I took the car back to the dealer and asked them to check, and it came back to me that the booster performs as per design. It is true that I haven't experienced any loss of brake power yet.
Meanwhile, the sound is getting stronger (and I don't think I am imagining it all, either). Now I have to turn on the radio or CD to muffle the noise.
(Now that my venting and ranting is done...)
Also, if it really is a vacuum leak, does it generate a code? So far, I have not seen any check engine light or check brake light and matchign description appear on the dashboard information console.