Kia - Sedona :: 2008 - Running Rough - Blinking CEL With Multiple Codes


Mar 24, 2016

I have a 2008 Sedona with the following trouble codes: P0018, P0300, P0302, P0304

I have replaced the coils and plugs, a torn air intake hose, and a camshaft position sensor for the side of the engine with even numbered cylinders.

It still runs rough has a blinking CEL, and gives the same codes.

I found that unplugging any of the myriad of sensors under the hood will keep the ECM in open loop so that it runs like a dream, but as soon as they are plugged back it, the trouble comes back. I used that fact to my advantage to drive the car to the mechanic a few miles away.

After running diagnostics, he says the ECM is bad based on the fact that the number 2 and number 4 fuel injectors stop pulsing after a couple minutes of idling. He says they are not even getting a signal from the ECM. He does not have the equipment necessary to flash a new ECM and recommends going to the dealership for a new one and getting it flashed there.

My question is, if I am being lied to, what do I need in terms of equipment to get a used ECM, install it and flash it with my VIN myself? If such equipment is cost prohibitive, can I contact one of these companies that sells ECMs and have them send me one preprogrammed with my VIN?

View 19 Replies

Advertisement

Golf IV / Jetta IV :: 2011 - No Fans Running While Engine Was Going - Multiple Codes Came On

I bought my 2001 Jetty w/2.0 only yesterday. While I was looking under the hood this morning, I noticed there was no fans running while engine was going so I took a trip to local auto parts store. O'Reilly's hooked up my Jetty and told me there was four error codes but they weren't sure what they meant. Here are the codes: P0302, P0301, P1128,and P1580. I have no clue of what these errors mean. I am not familiar with Volkswagen at all and there are no volkswagen dealerships close.

View 3 Replies

Jeep - Liberty :: Idling Rough With No Error Codes - Multiple Cylinder Misfire

ODB2 Code: P0300 - Multiple Miss-fire

I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.

So here are some basic info pieces:

1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.

There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.

View 7 Replies

Accent MC (2006-11) :: 2008 - Multiple Cylinder Misfire Codes

We bought the car used for my youngest daughter and it had a couple of codes in it. 1st was the o2 sensor.. easy fix, grabbed an OEM one and stuck it in. Then there was the Cyl 2/ multiple cyl misfire codes that kept getting thrown.

I've seen a bunch of post about people pretty much doing the same things I started out with and still having a problem.....

1) Swapped around all the coils.. still got a #2 misfire... So, coils are good.
2) Swapped in NGK Platinum plugs with a .032 gap.... still getting misfire.
3) Replaced the crank shaft position sensor...... still misfire
4) Noticed that there was an Ebay injector in the #2 cyl...... when I pulled the plugs, that cyl was running a little lean..... bought an OEM injector to go back in there...... still getting misfire

SO, I tried using a propane torch head and putting out gas around the intake to search for vacuum leak and got no response....... so, for the heck of it, I went old school and grabbed a can of starting fluid and started spraying it on the intake around where it bolts to head... bam... found a vacuum leak on #2 cyl....... ordered an intake gasket off of ebay, spent about 3 hours on it pulling the intake and replacing the gasket,( the bolts had loosened up over time and there were small tears in the gasket allowing it to suck air) .. put the new gasket on, cleared the codes and it's been running perfect ever since.

Check for a vacuum leak where the intake manifold bolts to the head... might save time and money.

View 3 Replies

Ford F-150 (2004-2008) :: Multiple Codes - Random Misfire Detected

I have a 2005 F-150 W/ 5.4 triton, and am having multiple codes. They are:

P0172- System to rich(Bank 1),
P0174- System to lean(Bank 2),
P0300- Random misfire,
P0303- Cylinder # 3 misfire detected,
P0304- Cylinder #4 msfire detected.

View 2 Replies

Prius (2004-09) :: 2008 Abruptly Slowed Down And Became Undriveable / Multiple Error Codes

I was driving my 2008 Prius and it abruptly slowed down and became undriveable. I had all of the warning lights - the red triangle master warning light, hybrid syatem warning light, and the check engine warning light. The car had to be towed home. The gas engine starts and runs - driving forward feels like the brakes are on - will not drive in reverse,. I checked the codes and had the following : POA1D, POA78, POA90, and POA94.

View 2 Replies

Ford F-150 (2004-2008) :: Truck Started To Develop A Miss - Multiple Codes

Apparently yesterday (no known reason) my sons truck started to develop a miss (so it feels like to me).

2005 f150 5.4 auto 215000km 4x4 stx. No specific cylinder codes. All general codes.

P1000
P1464
P1550
P1703
P1780

None of which I can see causing the miss. No check engine lite, no other codes. Not sure what to look at next. I am starting to disconnect the coil packs one at a time and see if I can pin down the cylinder.

View 4 Replies

Ford Super Duty (1999-2016) :: 2008 F350 - Multiple Codes / Cylinder 5 Misfire

My dads truck started misfiring last week, first thing i did was scan the codes and got p0303, p0304, p0305, p0306, and p0308. Its an 08 F-350 5.4...already changed out the spark plugs and the same codes came back. I decided to do some further testing and so far all coils had spark as well as 12.4 volts going to each. I did check the switching signal and that was present as well.

Moved on to the injectors and i checked each connector with my noid lights and it flashed on all cylinders. Did a resistance check on each injector and they all registered 12.4 ohms. We did switch some coils around and all the same cylinders misfire. My next step is to do a compression test.

My biggest question is if there are any common problems with these engines besides the coils, by the way this truck has the brown coil boots and the spark plugs that dont break in the engine.

View 3 Replies

Golf V R32 :: Check Engine Light Blinking - Car Running Rough

Our R32 has 2428 miles- and today the check engine light came on and it started to run pretty rough, babied it home and the the light was blinking when I turned into the driveway.. I know that booklet 3.2 in the owners manual is diagnosing catalytic converter issues...I have always used super unleaded, it hasn't even reached the halfway point of the first service.

View 10 Replies

Ford Super Duty (1999-2016) :: 2008 F250 V10 Missing / Dead / No Power And Multiple Codes

I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.

View 1 Replies

Passat (B5) :: 2002 Running Rough And Yellow Engine Light Blinking Then Turned Off

Drove fairly fast (160km/hr or 100 miles/hr) then took an exit down a ramp and had to stop at a red light. Noticed all of a sudden that the engine was running bit rougher and then noticed the yellow engine light blinking. I know to turn off the engine immediately when this occurs but then all of a sudden engine light turned off and car was running smooth again.

Car has been reliable for 7 years - proper maintained, synthetic oil, 171000km, timing belt changed, burns very little oil, good torque. Should I have it checked by the dealer (fantastic fair vw dealer)?

View 3 Replies

Suburban :: 1996 K2500 Running Rough / Getting No Codes

My '96 K2500 w/7.4 is running rough.

I've replaced: cap, rotor, fuel pressure reg, injectors (Bosch Design 2's), plugs, wires.

Had it timed today and it still runs rough. Really rough sometimes. I'm getting no codes.

In the morning when the engine is cool, I'm going to pull the pugs and check them, and verify the plug wires are installed correctly.

View 8 Replies

Golf IV / Jetta IV :: ASR Light Came On / Running Rough And Smoking With Codes

I was driving along the highway cruising at around 100 km/h when out of nowhere the car started driving a little rough so I look down and the ASR (traction control) light was on. I got off the highway, shut it down and fired it back up. The ASR light was off and car running like normal. When I got home I scanned it and these codes came up:

The catalyst code if from my catless turbo-back exhaust which I plan to fix next month with a tune. Anyway I cleared all codes and continued on my way without any other hiccups. So is my MAF sensor dying/dirty? ECU? N75 valve? Boost leak? I'm making a boost leak tester today just to 100% eliminate that variable, though I'm fairly certain I'm good there.

The car is mostly stock except for a few bolt-ons, all of which I've had installed for thousands of kilometers now. Here is what isn't stock, not including suspension, wheels, etc:

Forge 008 diverter valve

034 Motorsports PVC silicone hose kit

Samco boost hose kit

Forge silicone turbo inlet pipe

Eurojet SMIC

custom built 2.5 stainless, catless turbo back

AEM Dryflo short ram intake

GLI MFA cluster

View 2 Replies

Santa FE SM (2001-06) :: Stalling And Running Rough - Codes P1166 And P1167

My 03 Sante Fe is running a little rough and is stalling. My Mechanic said this P code was going to run me $1300. I'm not very mechanical , but this just seems very high. He said that aftermarket sensors would not work and only Hundai parts for the fix.........

2003 Sante Fe, LX, 3.7 l engine

View 6 Replies

Golf IV / Jetta IV :: Running Rough And 3 Codes Stored - Cylinders 2 And 3 Misfire

So my daughter's 2000 Golf Mk4 with 160,000 miles on it was running rough and had 3 codes stored - cylinders 2 & 3 misfire and a 411 secondary air injection problem.

Having had the misfire code before I swapped injectors around and the error code moved cylinders with the injectors so I attempted cleaning them and also cleaned the throttle body and intake manifold. At this point car still running rough but also started smoking badly.

Replaced the following items:

- Spark plugs
- Spark plug wires
- PCV valve
- PCV hose
- Fuel injectors w/ remanufactured

Hose reconnected between secondary air injection pump and air intake - previous owner had duct-taped it in when he couldn't get it to seal I guess. I've never heard it run.

Car running better, idles more smoothly, doesn't stumble or stall like it did before, no error codes coming up BUT car smokes a lot and the fumes make me feel sick just driving it a mile.

The car had never smoked like this before, hasn't had a whole lot of love the last year or two but no real problems either so why the sudden smoke?

At first I assumed it was cleaner being burned off but that should have been gone in under a minute and this is on-going. It's bad enough to not only be embarrassing but apparently dangerous as the fumes are bad.

View 11 Replies

Accent MC (2006-11) :: 2008 - CEL Blinking / Car Started Stuttering And Idle Was Rough

I have a 2008 Accent. Yesterday the check engine light started to blink and the car started stuttering and the idle was rough. I've changed the air filter, which worked. But, it was recommended that I change the fuel filter. But, when I went to the parts store, they say that this model has a fuel strainer instead. What is that and where is it on my car? Is it easy to replace?

View 4 Replies

TrailBlazer :: Running Rough And SES Light On - Codes P0340 And P0300 Misfire Detected

04 trailblazer, 4.2. Running rough and SES light on. Had codes pulled and showed p0340 (CMP sensor circuit malfunction) and p0300 (Multiple engine misfire detected). Replaced the CMP sensor and left negative battery cable unhooked for 20 minutes or so to clear the codes. Upon start up no more SES light and idle was slightly better. Within seconds it SES was back and it is again running poorly. Cruise control is no longer functional as well.

View 7 Replies

Rodeo :: 2000 - Both CATs Replaced Now Car Running Rough And Throwing Misfire Codes

So I just had both cats replaced and now the car is running very rough and trowing out mis-fire codes. What could cause this? Going to disconnect the battery to reset the computer to see if that might work.

View 8 Replies

Prius (2004-09) :: Diagnostic Codes P0K92 And P0K7K - Car Started To Running Rough

I have diagnostic trouble codes P0K92 and P0K7K set on my 2008 Gen. II Prius. I have searched the forums and cannot locate these two codes.

I started and drove my car for several miles today, then it started to run rough. I pulled over, then called a tow truck to tow my car back home. I have a high-level scanner/code reader that read P0K92 and P0K7K codes.

View 19 Replies

Ford F-150 - 1997-2003 :: 2002 V8 Running Rough - Codes PO353 And PO171

2002 F150 5.4 v8,,, I had troubles just over a month ago with a po305 code. i got the truck fixed with 2 new coils n some gaskets. I am having these po353 & po171 codes pop up now. The truck is running rough and I am curious to if its just another coil problem or if their is something I am overlooking or just don't know about?

View 1 Replies

Ford F-150 - 1997-2003 :: 2002 - Running Rough - PO316 And PO306 Codes

These are the code that keep spitting out. I have a 2002 f150 5.4L supercrewand it is running rough. I had this problem about 3 months back but i didnot get any codes from the computer i washed my truck a 1/2 day earlier, 2days later it went away. this time it has spit out 4 codes a po306/po307/po300/po316. the po307 and the po300 are gone, but the other two remain and it is still running rough 2days later. i had just washed my truck 30min. before, it started happening, is there water somewhere? My dad (long time mechanic) says use wire dry on the cops and it will go away. I have read other post on misfiring and I am still not sure what to do?

View 10 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved