Intrigue :: Code P1811 - Transmission Going Into High Pressure Mode
Mar 31, 2010
About 11 months ago I had hard shifting with the 2000 Intrigue.. Local Tranny shop diagnosed P1811 and replaced the pressure control solonoid. Then about 10,000 miles later problem occurred again. Transmission shop said they would either redo the solenoid or rebuild the transmission. I asked for a new solenoid.
Now today I'm having P1811 again. Clear it for a week and it comes back. Transmission is going into high pressure mode making driving very harsh.
PCS Solenoid shows operation at 60% duty cycle with approximately 1 volt signal. Shifting times are about 0.4-0.5 whenever I have a scan tool on it. What is reasonable shift times for the 4T65E?
View 12 Replies
Advertisement
2000 Intrigue 144,000 miles.
When you first start it up, the vehicle won't move in any gear. After a while of idling, it may start to drive, but the engine RPMs are way too high for the corresponding speed that you're driving. 4000 RPMs to hold 45 MPH.
Could this be the input piston? I've heard those wear and then don't seal well, bleeding off fluid pressure. Torque converter?
Also, the one diagnostic code is P0742 - TCC stuck on. I realize that this could be unrelated to the vehicle not moving when cold.
View 5 Replies
I have a 00 impala w 4t65e tranny I believe I have a p1811 code of hard and long shifting. I also need both cv axles replaced. If i replace the axles and have then dropped. Is it possible with the pcs going out, i would be able to drive 600 miles both way to a family thing without getting stranded.
View 3 Replies
So have my first code and its the P0088 error. Seems to be a reading that fuel pressure is high. I feel no loss of power or any issues when it throws this. HAs Happened 2 times in the fast 3 months and the last one seemed to clear itself after a couple hours. VW is saying its APR stage 1 even through APR tunes (stage 1) don't change the fuel pressure. Not sure if its a sensor issue, the start of a bad HPFP or simply a weird effect from the tune. Again I have no power loss or any other notable issues.
View 5 Replies
I've got a 03 x with the 6.8 2wd 4r100. It was flaring pretty bad for a while going into lock up, about 2 months ago the flare went away now NO lockup. Its taking more pedal to get moving and alot more slip, once you reach cruising speed tranny goes into high pressure. Told to replace the selonoid pack, got one use from a tranny shop from a tranny that lost reverse, got it home took mine out and found out the new one is not PWM and mine is, I tested my selonoid by putting 12v to pin 1 and 4 and nothing (on the pwm pack) did it to the new pack and it works. My question is what will happen if I put the non pwm in my tranny that originally had pwm pack in it?
View 2 Replies
I have a 2003 Ford Excursion with the high pressure line leaking. My guess is that the original line had a rubber hose and was replaced with a 3/8" ID high pressure hose. My problem is that I can not get the 3/8" ID replacement hose over the second larger bulge on the line going to the radiator cooler. What am I doing wrong?
View 3 Replies
The shutdown happens a few times a year. Got worse recently after topping off tire pressure. I'm assuming this is a ground issue. Will check the ground coming off the battery if there is one. Everything else seems fine other than lots of radio static on some days.
View 1 Replies
I just got an Egde Evo which I installed and everything looked great. After a few runs, I noticed the ABS light coming on an soon after that my transmission goes to limp mode (the wrench lights up).
I receive the DTC error: P2106 on the Edge Evo.
I have gone back to Factory default, but it keeps coming back, ie. the ABS light lights up and the Trans goes to Forced Limited Power (according to the Evo).
View 6 Replies
I have 2008 LS460 done 30,000 miles since last few days. I have CEL and when i hooked it to a reader the code came out P1235 "High pressure fuel pump out of range" any one had this problem before!
View 3 Replies
So I've gotten this error code a few times now but never a CEL nor does the car drive any diff.
1 Fault Found:
000136 - Fuel Rail/System Pressure: Too High
P0088 - 000 - - - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 0
Fault Frequency: 1
[Code] ....
View 5 Replies
This is on my 99 v10 Superduty. What I'm hearing sounds like high pressure fluid passing through a restriction. I only hear it when in drive or reverse while sitting still. The noise goes away once I get moving a couple of miles per hour. It just started making this noise within the last week.
I change the fluid every other oil change (about 6000mi on the last change) and am using M1 Synth in it. I only drive 10min between work and home so it probably barely gets warm. I don't know yet if it there hot. I'll have take it up the hill and back to see if it is temperature related.
Other then the noise it still drives and shifts fine. But it is pretty loud sitting at the drive through window. I'm going to drain it and change the filter this weekend and see how the fluid looks. Any thing else I should look at or other possibilities? I crawled under it last night and I think the noise is coming from the TC.
View 10 Replies
My truck gave me low fuel pressure and reduced pressure limp mode at 21,000 miles. The fuel and air filters were changed at 16,000. The dealer said all they found was the fuel filters (at 21,000) were what needed to be changed. Also, why does my truck hum??
View 14 Replies
Running the A/C for 20-30, I notice the fan not blowing at all even setting the speed to high. I hear something blocking the duct work. I stopped for lunch and when I came back I notice water still pouring out from the A/C
Huge puddle, almost cover half the car. Checked the fluid and confirm it was water. Where is the drain and what can I do?
View 4 Replies
I have a 2000 Olds Intrigue V6-214 3.5L, My Torque Converter locks after good and warmed up. A code 742 comes on when this is happening. I’ve looked into replacing the TCC solenoid or I’ve read where you can cut the wire going to the TCC.
If I cut the wire (not what I really want to do) I’m not sure which wire to cut. I need to find a good wiring diagram.
If I replace the solenoid (I think I am capable) I’m not sure which one to replace. I work part time at Auto Zone and they list the lockup solenoid the same as one of the shift solenoids. If it is one of these which one is I’m assuming it would be the 2-3 shift solenoid. There is also the TCC Pulse Width Modulation Solenoid valve assembly.
View 2 Replies
I have a 2000 intrigue (w/ a 3.5), it is leaking tranny fluid pretty bad. I cleaned under the tranny to see where it might be leaking and I was hoping it was the tranny pan, but it is not. where else would it be leaking? it looks like its possibly coming from the passenger drive axel. how hard is it to fix it? I keep adding fluid so I dont wreck my transmission but this cant go on for ever.
View 2 Replies
So I have had this code P0442 for a long time and I just kept clearing it. The attached picture (at an angle) shows the hole in the small line attached to the fuel neck filler exactly behind where the plastic wheel well cover touches it. Just ordered a new one from rockauto for about 65 shipped.
View 5 Replies
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
View 14 Replies
When I bought a used camry 5 years ago and drove it on the highway, my front tire busted and damaged the fender cuz it had too much air!! I wonder if it shows high pressure on my 2010 gen III Prius v with ATP. I know that the tires are special on this v version but still I like to keep a slightly higher pressure in the front ones because the lane keep assist feature works better with higher tire pressure. Summer is coming up so that gets me worried what to do with tire pressures.
View 10 Replies
My 2008 Tundra's tranmission went out last week when attempting to shift from 4 WD high, into 4wd lo, then back into high.
I was stuck in the snow in 4wd high, then tried low, to no avail, tried the transmission in lo (which didn't engage--just 'lo' light blinking and alarm buzzer, then tried 4wd HI and there was NO transmission response, a grinding in "P' and no low, high, or anything--from Park to D, Reverse, all the gears were gone, and I was getting ready to call for a tow truck, and after grinding the P gear for a while and back into N, it went into 4wd high.
Toyota replicated the problem, after some doing, and they're trying to fix it as the 4wd acuator is a problem--it's backordered to Japan which means the truck is out of action for a month.
There are similar reports of damage and problems listed on the NHTSA website.
View 27 Replies
Have hissing sound from prius c during ev mode? Mine has it, like whistling/ high frequency sound.....
View 4 Replies
I have rebuilt my transmission but it keeps burning up reverse high clutch plates. It has burned up two sets so far. I am thinking that it might be something stuck in the valve body.
View 4 Replies
