Infiniti - G20 :: 1995 - Runs Rough On Second Start
Feb 10, 2015
1995 G20 5.7L... This van runs great when first started and continues to run fine after it's warmed up and will do so until it’s turned off and restarted. When first started vacuum at idle is steady at 21” and 10” at 55mph cruising speed. I can continue driving for an hour or so and it will continue to run fine. It's only when I shut it down and restart after 20 minutes or so that I have a rough running condition. After parking for 10 to 20 minutes and restarting idle is still steady at 21” vacuum but the van hesitates on acceleration and runs rough at cruise with a 5” vacuum. If I continue to drive I get low vacuum trouble codes for the MAP and Oxygen sensors. I’ve replaced the oxygen sensor and performed a diagnostic on the MAP sensor which checks out ok. I’ve checked for vacuum leaks – none found. I've replaced the spark plugs, cap and rotor. What to look at next?
View 8 Replies
Advertisement
I have a 1995 GMC that I have owned since new. It has 212,000 miles on it, a 305 TBI, and a manual five speed. It started running bad all at once. It idles rough, at different speeds and never settles down, (between 900 and 1300 rpm. It smells like raw gas, smokes, and has no power to get started from a stop. I checked the vacuum, it is at 19" at all rpms. The MAP sensor reads 0.3VDC when off, 4.12VDC when idling, and 1.5VDC at WOT. It appears to have 12PSI fuel pressure (after a messy test set up!) on the fuel pump side of the fuel filter (filter replaced 10,000 miles ago). The EGR valve appears to cycle OK when I suck on the vacuum line so I assume it works OK. I found a bad TBI flange gasket and replaced it. It runs slightly better but still smells like raw gas and has no power. When I try to accelerate, it immediately has no power, like a big vacuum leak. The idle is close to normal (900rpm = normal). Do I just start replacing parts?
View 9 Replies
So I have a 95 aerostar 3.0. I use it every day my a delivery vehicle. I keep it maintained. About a month that ago, it developed a skip or a hesitation, most!y at high speeds, usually under load. I thought it may be transmission but had it checked and was ok. I drove it like that for several weeks. Then got worse so I parked it for ten days until my mechanic was available. When I cranked it to drive it over, it spit and sputtered the whole way here and barely made it. It had never done that before. He changed plugs and wires and distributor cap, even though it had been less than a year since all that had been done. Still no change. Driving way worse after sitting for ten days.
View 6 Replies
I've got a "new" Blazer -95 4.3 vin W about a month ago. It has run about 170,000 km.
But now it looks like it was a bad buy, it runs bad. The rpm starts jumping between 1500 - 2500. Suddenly the break and ABS warning lights in dashboard lights up, and sometimes all black out and it stalls.
At first it started acting like this when towing a trailer on the highway, doing 80 km/h. But now it does it at any speed.
View 14 Replies
My friend just bought (one week ago) a 1995 Infiniti G20T with 130,000 miles. The car is in great condition, except for the flecking/peeling gold paint (common problem with gold or silver paints?). When he bought it the car had a couple minor issues and had the "check engine" light on. After researching a bit, we figured that the possible issues causing the check engine light couldn't be too severe, given the car's asking price. So, he buys the car and I look up how to check the "check engine" light codes. I manage to get at the ECU and record (with the blinking red light) two codes: #34 and #105 - knock sensor and EGR + canister and control soleloid.
Good news, I told him. Both of those are relatively cheap to fix. So, I close up the ECU access and ask to borrow the car to run a couple errands. So, I go to one store, shop, get back in the car, make another stop at a store, get back in the car, make a third stop at a store and as I'm parking the car appears to start to loose power - engine seems about to stall and lights fade a bit. I rev the engine and it's fine. I (stupidly) go into the store and return to the car which now won't start. Turning the key to the crank position produces "click click click" and nothing else. Radio and lights work, but I turn off all these in case it's a low battery. Again - click click click.
View 12 Replies
My 99 250, 7.3 is having some strange issues as of lately. When I start it in the morning, when the engine has fully cooled down, it starts right up, then it throws the "wait to start light" runs real rough and just shuts off. Run the glow plugs a few times, start it up and it will do the same thing for maximum 30 minutes, then all the sudden I start it and it runs fine. I've replaced the fuel pump, cleaned the fuel bowl, new fuel filter, I just don't know where my problem could be. It doesn't make sense. But once I get it running and it warms up, runs fine all day. Go to bed, wake up, has problems again.
View 14 Replies
I'm working on my sons 1985 Celica GT 22RE. He was having problems with it running rough.
I've isolated it down to the number 1 cylinder being starved on warm starts. If you cold start it the problem does not occur but if you let it sit warm for 15 minutes it will fire up but nothing from number one cylinder. Lots of spark but no firing. So I'm going to tear down the EFI and move the injector to see if the problem follows it. Will probably see if I'm getting any voltage to the injector while rough before tearing down.
I can't find anything about an injector not working once warm so I'm thinking it may be an ECU problem.
View 5 Replies
I'm having a weird issue with my 1998 Ford ZX2. The car is very hard to start when cold and it runs extremely rough, but only through my first acceleration under load. In other words, I can rev the engine a few times while in neutral, and it will run very rough, and once I start driving, it runs really rough through my first acceleration, but then it smooths out and runs fine from then on until I stop it and let it call off for 30 minutes or more. If I restart it within 30 minutes or so, everything is fine, but any longer that that and the problem reappears.
View 3 Replies
I bought a '99 MX-5 in the fall with 100000 miles on it. Most of the time it runs fine. But about every two weeks when I go to start it it will run real rough like its only hitting on three cylinders then will eventually smooth out after anywhere from 5 seconds to 2 minutes. But today it wouldn't start at all. Finally started just fine after trying for 15 min. My mechanic changed the EGR valve but it hasn't worked. The check engine lite stays on all the time but when it starts rough the lite will flash.
View 3 Replies
96 civic 120K miles, stock, automatic.
In March I was running low on fuel, maybe 1 gallon left in the tank. It took a few cranks and on the last try i gave it a little gas and it started, albeit very rocky for about 1 minute of driving, filled up immediately and 2 freeway miles later, no real issues. I live in LA so very low ambient temperature is not a problem.
April through May, starting was a little rocky, it was inconsistently rocky too, sometimes there was no problem. Usually it's weak, stuttering, sometimes just cranking but I seem to get it to start. I stopped giving the pedal gas because I read that's bad (I own a vintage bike, so it's news to me). I don't drive that far and figured I'd try some Seafoam and some freeway miles would clean out any debris. Worked for that tank a bit for the next tank before the problem came back.
Still getting the rough starts, but now when I give the car gas as I pull out sometimes it doesn't accelerate for 15-30 seconds, maybe 25 yards then it drive like normal. No dying at all but getting worse with starting up.
I've tried turning the key (not turning the engine over) 5 times and cranking on the 6th and it seems to work. I thought maybe it's the fuel pump or fuel filter but read it could be an ignition coil/ spark plug/ spark plug wire issue. Two different ball games.
My MPG is not really droppingI had a new fuel filter put in in February as routine maintenance (thing was on so tight had to bring it to a shop so no rookie mistakes there). Timing belt &water pump replaced 6,000 miles ago
View 3 Replies
My 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 Replies
I am working with a friend on his 99 Ranger with a 4.0 . When first started it will idle rough and hesitate for the first 300 feet or so, and then clear up and run smooth the rest of the day. If he lets it set for 6 or more hours it will repeat the problem. He has taken it to a local Ford dealer and they have replaced spark plugs, plug wires, coil pack, cleaned the throttle body, checked the air idle motor and passage.
He has had it to the dealer 3 times and their latest plan is to pull the heads @ a cost of 1500.00 to start. Since it runs well, no coolant in oil or oil in coolant nor loss of either fluid, I couldn't figure why they want to pull the heads.
To date it has not thrown a code, I ran it on a New Generation Star tester and cannot find a code. The truck runs great after the first intial start up and does not give any signs of cutting out or lack of power. My guess is it is losing fuel pressure overnight and is taking a while to reprime. Original fuel pump and 160K miles. Will do a fuel pressure test this weekend.
View 1 Replies
I have a 1999 Ford Escort SE wagon with 112k miles on it. Last week when leaving work my car started very rough. This was unusual so I killed and restarted the car about three times before letting it run it's course (~30 seconds), after which the car ran fine. About a week later on my way to work the car seemed to 'sputter' (for lack of a better word) when I pushed down on the petal looking for some power on two separate occasions. On each side of the sputters the car seemed to respond fine, but when it did sputter there was a severe lack of power. I got to and from work just fine, but while letting the car idle in the parking spot of my apartment for a minute before shutting off the engine the check engine light finally came on. The following morning the car again started rough (as if it were misfiring/running on 3 of 4 cylinders) and this time it took a good minute before smoothing out. However, after the car smoothed out I experienced no issues on the way to work, no sputtering, no loss of power, nothing. Doing some initial online research I feel that the problem may be one (or more) of the following:
-Fuel pump
-Vacuum lines
-O2 Sensor
-Spark plugs (they are original)
-Fuel Filter (it is actually past due for replacement)
I plan on getting this checked out ASAP, but that still may be 2ish weeks away with my schedule. Some similar reports say that I may be having a 'lean mixture' issue (not getting enough fuel), but I haven't had the time to check the code. My question is, how "safe" is it to continue driving my car with the current situation? Is it at a super high risk of failure/random stalling during rush hour? Will it cause any damage to the engine if there is a cylinder misfire upon start up? I was also wondering if the car would be reasonably reliable to drive on a ~400 mile road trip on an upcoming weekend, but I am making plans as if it is not.
Additional Details:-Tried charging the fuel lines (car to 'ON' then 'OFF' position 3-4 times), had no effect on the morning start-up-Commute to/from work is about 20 miles
View 13 Replies
About 2 weeks ago my 1997 Buick Park Ave (115,000 miles) began running bad during a heavy rain storm. It was running fine. Then all of a sudden at a stop light the motor hesitated and wanted to stall. I nursed the gas peddle and limped home and turned the car off. The car hesitated and sputtered all the way home as if I was running out of gas.The next day the car would not start. It turned over but would not start. I tried starting the car for three days. My mechanic friend later diagnosed the car and stated the computer was not functioning correctly. He replaced the computer. The new computer seemed to correct the problem.
The car ran great for the next 2 weeks. Yesterday, it was raining hard while I drove the car about 150 miles without any problem. Then suddenly again the motor started running badly. Again, the motor wanted to stall and hesitate as if I was running out of gas. I limped home again. This morning I tried to start the car without any luck. In addition to installing a new computer, In the last 2 months I have changed all the fuel injectors and installed new spark plugs.I have also changed the fuel pump and repaired the fuel tank. My mechanic say the cam sensor and crank sensor are operating correctly. There is spark coming from the coil packs and to the spark plugs. I do not want to randomly change parts.
View 3 Replies
I got 2000 tdi with 270000km on it and have a few issues with it and am looking for some information before i start doing some work to it.
First problem excessive blue smoke on start up also runs ruff tell it warms up.
Second the is a screeching noise on start up some times. happens most of the time when the car is cold.
Third sounds like something is dragging or rattling but i have checked and there is i can see.
Fourth when the clutch is in and the brake is on the car runs ruff at idle. i think it has something to do with vacuum used for the brake booster but not sure.
View 1 Replies
I have a 2000 E350 boxtruck with a 5.4 auto. The motor is a new rebuilt with about 4000 mile, coils were replaced with motor, injectors were rebuilt with motor.Today (500 miles from home) the truck died. I was going up a slight hill on an interstate. It will still start, but runs very rough and when I put it in gear and step on the gas it dies.
So I had it towed to a garage. While pushing it into the garage I noticed my gas cap was missing. I know it was on 45 min earlier because I got gas. Did I forget to put in back on? probably.. But I wondering if the missing gas cap could cause the truck to run bad,vary bad?
View 14 Replies
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
View 14 Replies
I just bought this 99 f250 7.3 Powerstroke last week.. drove it all week fine, I car pool with a family member to work and asked his girlfriend to plug my truck in for me, well she didn't and it had stalled on the way home one morning but started up after cranking a few times i thought nothing of it. Drove it a little bit that day and it was fine, while I let it idle in my drive way as I prepared to go work it started running really rough then died. It took a long time to start again..now it's happening all the time. I changed the fuel filter and someones telling me there's air in the lines..
View 5 Replies
I have an 03 F350 with the 6.0L. It has 210,000 miles on it and the injectors are beginning to be suspect. Its very hard to start when its cold, smokes and runs like crap untill it warms up.
I've found a set of injectors out of a 2005 truck with 8000 miles on them. The truck was overboosted and blew a head gasket.
Now finally to my question.....Can the overboost damage the injector? Would it be safe to buy these and install them or rebuild them before install or just leave them alone?
View 14 Replies
1995 Honda EX with 150,000 miles. Its been running rough ie rough idle, stalling at low rpms etc Additionally for awhile now when humidy reached north of 85% the car wont start. It cranks but rarely runs.
Took it to a mechanic last week for a tuneup. They replaced the Distributor cap, spark plug and wires and fuel filter. Car ran great for a day. Then progressively got worse. Was undriveable the other day stalling misfiring while at speed. Took it back today. They determined that it was still not getting spark and replaced the distributor. They did so, test drove it, declared it good and I came to pick it up. Paid the bill, walked out to the car and the damn thing would not start. Humidity was high.
Mechanic pulled a spark plug and put a tester in and didn't get a spark when cranking. He is assuming the distributor he just put in is bad. So they are keeping the car overnight to be fixed in the morning with a new distributor.
However I'm not convinced the dizzy is bad, I believe, as I've read that the Honda's ECU is probably bad and shorting out in the high humidity. Can a bad ECU would prevent spark?
View 2 Replies
This problem has been getting worse over the last 2 years. When the car starts it idles fine at about 1000 RPM. As soon as it warms up, it starts to idle rough, between 500 and 750 RPM. It almost quits running. As soon as you give the car some gas it runs just fine. About 3 weeks ago I got a "Engine Lean" check engine light error. I reset the system and have not gotten the error again. Since then I have: changed the MAF cleaned the EGR (made sure it closes completely and ohm out the coils in the actuator) changed the O2 meter on the exhaust manifold cleaned out the throttle body Ohmed out the air idle controller. What I should check next. I was planning to check the fuel pressure in case it is a fuel system problem. It is a 1999 ....
View 5 Replies
