Hyundai - Accent :: 2003 - Clutch Squeaking When Depressed
Jun 27, 2011
Earlier this summer I bought a 2003 Hyundai Accent with 130k miles on it. Recently I have noticed a squeaking/squealing sound coming from underneath the hood. I first noticed it at traffic lights, but I have determined that it occurs whenever the clutch pedal is depressed, and continues until the clutch is released.
My first question is - is this serious? (Is it dangerous, or will it compound significantly if I do nothing?) The clutch still seems to work fine, and I can stop the noise at traffic lights etc... by putting the car into neutral and letting off the clutch.
My second question is, how did I cause this? Coasting with the clutch fully depressed, or too much downshifting?
Background: Recently, I bought a Scan Gauge to provide real-time fuel economy feedback, and began to experiment with different driving styles. I found that I could really boost my fuel economy by coasting down longer hills on the highway (when there were no other cars around). To do this I was pressing the clutch all the way to the floor, figuring it was the same as putting the car into neutral. When my speed began to decline after the hill I'd ease back into 5th. One hill in particular comes into town where there is a light. If the light turned red I would stop coasting and do some quick downshifting as well as breaking. I was pretty aggressive with the downshifting on a few occasions.
Did either the downshifting or the coasting likely contribute to my problem? If coasting was an issue, would coasting in neutral cause a similar problem?
View 2 Replies
Advertisement
2009 Accent 5 speed 66K miles. This is something which I recently noticed with the onset of winter. When I depress the clutch pedal, I have a very audible squeak. Think old door hinge squeak. So metal is rubbing against metal somewhere inside the bellhousing without enough lubrication.....not good. I pulled off the dust boot on the side of the bellhousing and tried my best to push moly grease around the clutch fork stud, hoping that was the origin. The noise went away for roughly a half a day but is back in full force....funny how cars do that.
Space seems EXTREMELY limited on lubricating the proper area. Or....is this a warning mechanism built into the clutch pressure plate assembly to warn of replacement soon? While I am asking these questions, what is a good time to look into replacing the clutch? The parts for the car seem relatively cheap, if I replace the clutch assembly, I may consider replacing the flywheel and clutch hydraulics as well as a whole system replace/refresh.
That aside, is there anyway to eliminate the squeaking without having to crack open the bell housing?
View 13 Replies
I have a 1999 Saturn Coupe with about 47,000 miles on it. Today, my clutch started squeaking every time I depressed it. Is this forewarning of something bad, or should I ignore it?
View 2 Replies
I bought my Hyundai new in late 2011. No problems with the car (other than no spare tire???) until just out of the warranty (63,000). Had a noticeable drop in power on the highway. No warning lights. Drove another 100 miles with power intermittently dropping. Next day engine light comes on. $800 later I have a new high pressure fuel pump. All seems well. after a few weeks, I notice that the car seems to be revving when I depress the clutch to change gears, like up to 4000 rpm's. If I leave the clutch in for a few seconds it will begin to decrease. But if I shift right into gear as I have done for the last 35 years of driving, it is not smooth, jerky. This seems to happen mostly going into 2,3, and 4th gear, always going up. It never happens when downshifting. I tried tapping the brakes when shifting up, and sometimes it does seems to drop the rpm's. What it might be. It probably is related to the work that was done, but I don't really trust the dealer and want to have a little info going in.
View 1 Replies
I have a 2009 Hyundai Accent with about 90,000 miles. I bought it with 30,000 from a dealership that had been using it as their "loaner" car. Don't know if the brakes were new when I got it, but let's assume they were.
The brakes have been squeaking since Day 1, especially when first driving. In the first few years of ownership I took the car to several different mechanics, convinced my brakes needed replacing. Was told that no, I had tons of life left on them and the rotors were in good shape. Each time they'd clean the dust off them and I'd be squeak-free for a day or two. After a few years of ownership, when it rained and I'd start driving my brakes would be SO loud and an almost-grinding noise could be heard. Not only that, but sometimes after a rainy night when I first braked, the car would almost lurch when making a stop. I honestly thought I had been lightly rear-ended the first few times it happened. Asked multiple mechanics to check the brakes and was told everything looked fine.
Now, I've put nearly 60,000 miles on this car. I still haven't replaced the brakes because each time I bring it somewhere to do so I get told I don't need it. I can't believe that brakes with 60,000 miles on them have any life left, but multiple mechanics say otherwise. The most recent mechanic attributed the lurching to moisture in the ABS. Seriously, what could be going on here?
I'm about to tell my mechanic to replace both my brakes/rotors next week no matter what, but it would be nice to know possible causes to my issue. I drive my toddler around daily and I just don't trust my brakes. One brake failure will be one too many. On a side note, this, coupled with low MPH, no power, and a transmission I feel is slowly on a death spiral.
View 14 Replies
The problem started when my clutch fluid began leaking a couple of months ago. I first noticed that it would take an unusual amount of effort to shift into gear and, after checking, found the clutch fluid completely gone and I filled it up immediately. Three weeks later, the fluid was gone again, so I took it in to a reputable mechanic, who said I needed my slave cylinder replaced. A week after replacement, I start to notice that my car increasingly had trouble "catching" into gear (my engine was accelerating, but not moving very fast; soft clutch). I thought maybe something went wrong with the slave cylinder repair and took it back to the same place, but the news came back that I needed a new clutch.
At 143,000 miles on the original clutch, I wasn't surprised it was time for a new one. Immediately after picking up my car with the new clutch--and by immediate, I mean right after I pulled out of the mechanic's parking lot--I noticed my car was driving horribly. The engine was idling extremely rough and it felt gritty when pressing the gas pedal during acceleration. I took it back to my mechanic the next morning to explain the problem, but they treated me like I was an idiot, didn't detect anything wrong with my car, and clearly didn't know what I was talking about even though I personally showed them my steering was shaking pretty badly while idling.
A few more days of the rough idle/gritty acceleration and I went back, but they just suggested getting my fuel injection system cleaned. I personally checked to make sure that the wires in my car were connected properly, as well as making sure the hose connecting to the air filter was on there correctly. Today on a whim, I took my car to Autozone to have them check the computer, even though I don't have a check engine light on, and sure enough the only code read was P0302--Cylinder 2 misfire.
My question is, what is the most likely cause of the cylinder 2 misfire (given my car's very recent history) and most importantly, could the mechanic have caused the problem I am experiencing? How should I handle this situation with them from here? I will no longer be using their services after I get this problem sorted out, as I feel like my car did not receive the best service.
View 1 Replies
My 2003 Hyundai Elantra has 94000 miles and is already on it's second clutch. It is starting to feel like this one is almost toast after only about 25000 miles. It feels like it is slipping starting from a stop (the tachometer goes up, I release the clutch and there is a pause before the car moves) and if I am in 2nd or 3rd gear and I accelerate the tachometer will often jump and the car will lurch. I have had a clutch go out before and it felt very similar to this, I just can't believe that this clutch would only last 25000 miles. I know that you can't adjust the clutch as it is self-tensioning, but I also know the mechanic who put in the second clutch had some problems and it had to be re-serviced after the initial replacement. Is there any way this guy did something wrong that could be fixed? Could the clutch really be worn out after 25000 miles? I'm the only driver and I don't feel like I drive the car too aggressively... If the consensus is that the clutch needs replacement, maybe you could throw out some figures so I know what I am getting into?
View 2 Replies
I'm driving a 2010 Hyundai Sonata and just recently one of my brake lights has been acting up. Everything works perfectly fine as long as the head lights are off; however with the head lights on, when I depress the brake pedal my driver's side tail/brake light goes out. The center brake light and passenger side brake light work just fine regardless of the head lights being on or off. With the headlights off, all the brake lights operate normally when the pedal is depressed.
View 6 Replies
I read all of the threads regarding clutch vibrations and other problems but I have 1,500 miles on my R and since day 1 I have been feeling a very slight ticking on my foot when the clutch is depressed. It gets more pronounced when I rev the engine a bit but nothing you can hear. Is this a normal feeling or should I not feel this at all.
I'm getting the APR tune next week and will do HPFP/intake soon but I need to be convinced that the Carbonio Intake is actually an upgrade from the stock intake with just a K&N filter, it doesn't look much different, the intake area looks the same as stock. I don't want to have to modify the engine cover or else I'd get the VWR intake. Any experience with the K&N vs stock vs Carbino?
Not sure if it was just the hot/humid weather yesterday but the car felt a little boggy when starting in 1st gear like it was running too rich or something. Any history of this?
View 12 Replies
This is regarding my 96 BMW 328i. It has approximately 177,000 miles on it. Over the past year, I've replaced the cooling system, fuel pump, alternator and trans fluid for kicks. So, I'm understandably frustrated with it. Anyway, to my story:
On my way into work, whenever I pressed in on the clutch, it would make a loud clunk/pop and freak me out. I turned around after 1/4 of the way and swapped cars.
My mechanical skills are maybe 3 on a scale of 1 to 10. I'm not afraid of changing oil, brake pads, transmission fluid, changing an alternator, etc. But I want to have someone to blame for anything that involves anything within the engine block/head/transmission continuum.
I noticed that a heat shield was loose between the driveshaft and the exhaust. I rapped it with a hammer, and the heat shield didn't make a noise anything like I'm hearing. So, it doesn't sound like that's the real culprit here.
View 5 Replies
2013 tdi 6mt. I am noticing that my clutch clicks when the pedal is depressed. it does not happen when I first start driving in the morning, but it seems that once the cabin is warmed slightly it starts then clicks each and every time. It is annoying and it appears to be related to the different temps outside vs the cabin. I did not notice it during summer or early fall but it is cold here now.
View 24 Replies
I have a 2003 Hyundai accent that was not shifting into higher gears about (45 mph) max speed. I took a transmission out of a 2005 ( same engine bad unibody) and put in the 2003. Making sure the torque converter was in all the way. Now I have no gears at all, no park, nothing. But the car does start. I went to the salvage yard and noticed that all the cars like it (hyundai) had no park either. So I must be missing something electrical right?
View 11 Replies
I've been driving manual transmission vehicles - from my '72 Pinto to big trucks - for 40 years. This happened recently in a VW Golf I had rented: While driving down a mountain in a tunnel in Norway, with the clutch depressed, there was a loud POP noise.The clutch became engaged, and the clutch pedal did nothing. I'll spare you the details of the harrowing aftermath, the language barrier issues in the sticks of Norway and such. In the end, the rental company is charging us a couple thousand bucks for breaking their car. I maintain it was not Driver Error. My local VM service manager indicated that the Slave Cylinder on the Golf has been a problem for years, and is probably what went bad, but - as a rep of VW - is not willing (allowed) to put that in writing. The garage that fixed the Golf indicated it was Driver Error. I'm guessing everything tranny-wise got beat up when the Slave gave out, making it look like I'm a bonafide Clutch Masher.
View 19 Replies
I have a 09 Sonata which when shifting once, the clutch depressed but did not come back up. While waiting for Hyundai service to come I tried to move the car down the hill to a shady spot on curb for my son and the clutch started working normally and has for 6 months...
View 2 Replies
So, I bought the truck used and everything about this truck is great minus the shifting difficulties in first. With the truck at a dead stop, the clutch depressed, and the shifter in neutral it can be near impossible to shift into 1st (it's possible with a lot - emphasis on a lot - of force). No grinding, clashing, knocking in the shift knob - it just wont go into gear. I can shift into 2nd-5th and reverse without too much difficulty. If the truck is in motion, once the vehicle gets between 2-5mph I can easily downshift into 1st. However, if I shift out of 1st and let the truck sit for, say, 5 seconds it is often very challenging to get the truck back into 1st.
I have tried to look up this problem online with limited success. What I found was it could be caused by:- something wrong with the clutch installation- a need to bleed the clutch (it's hydraulic and, although the reservoir is full, the fluid is a bit dirty)- perhaps a faulty clutch master cylinder- play in the clutch linkage- a broken spring in the pressure plate- a bearing that is starting to go out- worn synchros in 1st.
I am a machinist, not a mechanic, so it's hard for me to evaluate these ideas (beyond the cost associated with each). Given my limited knowledge of transmissions and my good mechanic friend's opinion, I think it's a broken spring in the pressure plate.
1990 Toyota Pickup 4x4 manual transmission. This is the original transmission in the truck, it has not been rebuilt (but has been maintained with regular fluid changes), and has a tad over 158,000 miles on it.
View 19 Replies
I have a 2002 Subaru Impreza WRX and recently it started making a squealing noise while the clutch is depressed at low speeds. I've researched that it's likely the pilot bearing or bushing? My questions are: should I have the entire clutch replaced? How much should it cost? And will I cause more problems if I wait too long to do anything? How long can I wait?
View 8 Replies
Ntices a strange idling noise? At first i thought it was just something like the radiator fan but it's tied to the clutch pedal..when the clutch is depressed the noise gets more isolated and a little louder. Everyone else in my car doesn't notice it but to me it sounds like something is out of balance... car only has 6500 miles on it and has never been driven hard... 2010 Golf 2.5 5spd .....
View 9 Replies
I have a 98 f150 with a 4.2L V6 and a 5 Speed M5R2 manual transmission, I recently got a rebuilt trans for my truck. I installed it with no issues, while my truck was still on jack stands I tested it out, it shifted into every gear no problem but after I took it off the stands and pulled it out of my backyard, when I take off in 1st its fine with the clutch being slowly released, but as soon as I let go of the clutch the truck just buckles and some times tries to flat out stop.
I'm not sure if I have a Clutch issue, Transmission issue or axle issue, when I tried it out on jack stands I had the stands supporting the rear on the axles so some of the weight of the truck was and the rear axle and it didn't buckle then so I wouldn't think it'd be the axles but when it was on the ground it'll buckle. I even had someone move the truck forward and release the clutch slowly until in was fully releases and looked underneath and saw the axle buckle upward,
What the issue is it only does that when the clutch is released or if I'm lucky enough to release it without buckling once I go to shift to second and press in the clutch the whole truck just comes to a complete stop without the engine stalling. I thought maybe it was a clutch issue and that maybe I put the clutch plate backward(which I'm pretty sure I didn't)but even if I did, I wouldn't even be able to shift it into any gear, at least that's what I think. I bleed the clutch before taking it out so I don't think that could be the issue either.
View 1 Replies
I know, sounds like blown head gasket. However oil looks fine, no coolant leaking and coolant looks fine. It also does not overheat (that I can see, it dies first). This all started a few weeks ago. I changed spark plugs, oil and undercoated the car with primer. I did get some paint on the radiator. I also put techron in the fuel tank and changed fuel filter. The car ran fine before, now here is what is happening step for step.
Car starts fine, idle is a bit rough (it was before too) but nothing drastic. I rev car at 2500 RPM until it is warm. The thermostat stays in the middle yet I begin to see a good amount of white smoke coming from the exhaust. If I take foot off the accelerator the car will shut off at this point. If the car is not warm yet, it won't shut off. When it does shut off, I cannot restart it even with gas pedal down. It just cranks and cranks. When I let it cool down it starts up fine and the same thing occurs. I cannot tell if the radiator fans are turning on as the car dies before they turn on (it's cool outside). The thermostat never indicates overheating.
The entire radiator is smoking white (not from cap) but I assume that is from my paint overspray burning off. Could this be getting sucked in and stalling the car out when the car warms up enough to start burning off the paint? Could I have painted something inappropriate? What could this be? I know a decent amount about cars.
If I let the car warm up just by idling it will run until it gets warm then it stalls and again, won't start until it cools. It seems to keep running if I keep RPMS up but right when I take foot off accelerator when warm it shuts off.
View 19 Replies
I recently had a problem with my car stalling when warm and not starting at all until cooler. This was the crank position sensor.
Now the car will not start without starting fluid. When starting fluid is used, the car will start and then run fine. Once you shut it off then try to start it, same thing. The fuel pump turns on when key is in on position. Holding pedal down to try and clear flood does nothing. Car just cranks and cranks but doesn't start until starting fluid is used.
So there is either not quite enough pressure at fuel rail, pump is not getting enough draw from battery, several other things could be suspect. Car is a 2003 Hyundai Accent. Battery tested borderline ok. It does the same thing with donor battery attached. I have a fuel gage but need an adaptor for it that I don't currently have to fit on this fuel rail. Stumped because the car runs beautifully once starting fluid gets it going.
View 19 Replies
I have a 2011 Tiguan 125TSI with the 7 speed DSG. When it starts cold, you can hear a noise that sounds like a bad gear change when going from 3th to 4th, and 4th to 5th. It almost sounds like changing gears in a manual car without clutch completely depressed. It has been there since I got the car brand new, but recently it seems to be getting worse.
Once the engine gets warm, the sound goes away and gear changes are smooth.
I've asked the VW dealer about the sound and they tell me it is normal. Is this right? The problem is it is very hard to demonstrate to VW the issue since it may happen only once when the engine is cold. I've left it with the dealer overnight and they were able to reproduce it in the morning... but again, they tell me this is normal.
View 2 Replies
