Grand Prix :: 2000 - Soft Brake Pedal Goes To An Inch Off The Floor
Oct 4, 2013
I have a 2000 Grand Prix 3.8 with 65,000 miles. Bought the car new for the wife to drive. The front brake lines rusted out. My wife has a friend who is a backyard mechanic. She had him replace the front brake lines, from the abs block to each front wheel. Well she finally told me that the brake pedal is not right. I went out and sure enough with pressure on the pedal it goes to an inch off the floor. I bled all for lines at each caliper, no change in pedal. I bled almost a full bottle of fluid. You can pump the pedal for 10 minutes and no change in the pedal. I don't think it is air in the line. I changed the pads and rotors on all four corners last fall. The brake pedal was normal then.
View 5 Replies
Advertisement
I have a 2001 Grand Prix SE 3.1 that the brake pedal goes to the floor. I did notice the fluid was low , filled it up. I do not think it sucked air, although I can not be sure of that. As you can imagine, it is a beater so don't want to stick a ton of money in it. I had someone look at it that said he thought it was a "sensor" that would cost over 500 bucks. I don't know of any brake sensors at all. If there is, do they cost that much? If not would this be a master cylinder.
View 5 Replies
My B6 purchased exactly three weeks ago has had a soft brake pedal since day one. By "soft," I mean that when parked with the engine running and applying moderate pedal pressure, the brake pedal provides some resistance but sinks to the floor. If I pump it up a few times, it temporarily gets much firmer, but eventually sinks to the floor again after a few seconds. Now the car so far has never failed to actually stop, and it can get into the ABS. But during an abrupt (okay...panic) stop last week, it did go to the floor while the car was still moving. That's when I decided that was enough and took it back to be serviced.
My expectation was that there was just a small amount of air in a line somewhere, and that they could bleed the system and fix it. That was my experience with my B5: it was very sensitive to the least little bit of air, and if it wasn't thoroughly bled after brake service the pedal often got mushy and could find the floor. But bleeding them always get the pedal back to normal. So the service advisor said that he "had the service manager drive [my car] and compare it to a new Passat [on the lot] and talked to "Quality Tech. Manager to confirm." And the confirmation was that my brake system is "working as designed." In short, they say the brakes are working properly and there is nothing to fix. So I have now picked up the car and it still does the same thing.
Now I can (and will) bleed the brakes on my own over the weekend. But I would like feedback from others as to whether or not their brake pedals regularly see the floor. I just can't see this being the way any hydraulic brake system should work..
View 21 Replies
Here's the short of it. 3rd time in a year the brakes on my 2005 SF (177K miles, 2.7L) have gone out.
The brake pedal is very soft and goes to the floor before braking occurs. Typical signs of a bad master cylinder.
The first time was a year ago. I bought a re-manufactured master cylinder, change it and bled the brakes. Worked like a champ and lasted 10 months.
To months ago same exact symptoms. I assume it was a bad re-man part. It's under warranty, not big deal. I do warranty exchange, bleed system, brakes return. All is good.
Less then 3 weeks later, brakes gone, same symptoms! This time I spend the difference and get a brand new OEM cylinder with reservoir. Replace, bleed, problem fixed. Brakes go out in less than a week.
I'm not leaking anywhere. Reservoir is to corect level. ABS light is NOT on. No chattering in brakes. Braking is smooth both when power brakes work and when not. No visible damage to calipers. I'm 99% sure there is no air in the system, but I'm going to try bleeding again. I have not put it up on a lift to yet to check all the lines.
View 21 Replies
I have a 98 gtp 2 door with the electronic dual zone climate control. I can't get air to blow much out of the floor vents. I applied vacuum directly to the actuator and air came from the vents fine. It seems there is a box behind the glove box that controls the vacuum to each actuator. My question is, would the issue likely be with that vacuum distribution box or with the electronic climate box itself.
View 2 Replies
The pedal used to go right down to the floor and would barely stop the car from a crawl, in response I have bled the brake lines to all calipers, and checked the hydro booster fluid level, and with only slight improvement the pedal almost hits the floor.
I am thinking the brake master cylinder is shot. The pedal becomes solid after about 15 pumps when off, and holds pressure, when on it takes several pumps to build any sort of pressure and cannot be built up to the solid point, and looses pressure quickly when just holding the pedal down.
View 3 Replies
I have a Hyundai Santa Fe 2005 2.7L 4WD ABS.
The problem is that the Brakes pedal is so soft, that it goes to the floor, and doesn't brake at all in first pedaling. I am able to apply brakes after pumping the pedal thrice in continuation and then when it builds up some pressure, then it brakes and I'm able to stop the car. Once, I take the foot out of the pedal, it goes bad again. Once, again if I have to apply brakes, I have to do 3-4 times pedaling.
The brakes are stopping the car fine when they get applied in 3rd or 4th pedaling and when pressure is built up. Its the pressure not getting built up or maintained in the first go.
What has been done by the mechanics to solve this:
1. Master Cylinder has been replaced with a new one. (This has been done twice)
2. Brake Pads have been changed.
3. Brake fluid has been replaced and is upto the brim in cylinder reservoir.
View 7 Replies
Details about my car: '91 Nissan Maxima. His name is Max. 183,265ish miles on it. Transmission was replaced maybe 8 years ago(?) My dad said the oil was changed at the 500 mark. Filled the tank up at Citgo with regular gas on Friday and only drove about 50 miles (I fill up every 200 miles or less). Max turns on but you have to floor it just to move an inch and it smells like gas.
View 15 Replies
I have a 2000 Grand Prix with a 3.8L engine that will not start. When I turn the key to the run position, the headlights and the dash lights come on, but when I turn the key to the start position, the lights go dim and nothing happens. No sound from the starter. I checked the battery and the starter and they are good. I installed a new positive battery cable. Still works the same. Not sure what else to check.
View 13 Replies
I have a 2000 GP GTP. I went over a speed bump to fast one day, and parked my car. When I got back into the car the next morning, I tried to put my car into drive and it wouldn't accelerate or move. So I put it into lower gear, 1st to be specific, and the car moved normally. I drove like that for a few days with no problem. Then days later I did the same thing, went over a speed bump to fast and now the vehicle wont move at all unless I put it in reverse.
View 2 Replies
Where does the 3rd brake light wiring harness plug into on a 2000 GP ? It's just hanging down and I don't see where it plugs into. I'm talking I'm the trunk area.
View 1 Replies
I have a 2000 grand prix gtp, I am trying to pull the motor so i can change some things up so i can race it. But how to pull the motor or transmission with it.
View 7 Replies
2000 Grand Prix GTP has code P1629, car will run for 3 sec with black master key and then die. Security light in dash is flashing when this happens. Tried the 30 minute relearn for PK3 with no luck. It will start and stay running with the grey Valet key which is perplexing to me. As of right now I am siding with replacing cylinder and ignition switch after everything I've read on the subject.
View 13 Replies
Cooling Fans and a/c compressor not working-2000 Grand Prix. They both work when I jumper them. Replaced coolant temperature sensor, checked fuses and relays -all good. Not sure what to troubleshoot from here.
View 4 Replies
Having an issue with my car blowing fuel pump fuses every once in a while under heavy to moderate acceleration. Have replaced inline fuel filter and the fuel pump resister(white ceramic part). Runs fine with normal driving, but when I want to get some horses out of it, it will cut out and stall and once i replace blown fuse it will start back up again, and I'm off and running again.
View 2 Replies
I have a 2000 pontiac grand prix (3.8) and when i was driving my car randomly shut off. When i tried to start it again, the car would start, rev a 1000 RPMs then dies a second later. If i pump the gas i can keep it running at around 2000 RPMs until i let my foot off the gas, then it dies After repeated attempts the tow truck was in need. the following day i ran some tests. when starting the car the fuel pressure would stay between 40-50 psi and doesnt drop below that. (excludes fuel pump, filter, etc..)
After running tests the car suddenly started up and continued to run with the rpm bouncing (+/- 100 rpm) i let the car run for 10 minutes and it began running perfectly. This has happened repeatedly in the past 3 days. I have noticed that when letting the car sit while runnig, it will usually die within 2 minutes, however if I am driving. It will sometimes be fine for hours. When attempting to start it by hitting the gas, the car will sometime sputter at 300 RPMs when hitting the gas will do nothing. in some situations i will hit the gas and the rpms will decrease and rise randomly. (letting my foot off the gas, rpms will hesitate before reducing).
When the car dies, i am at times able to get it running after spending 30 min fiddling with it. But half the time it wont start. I have a -P0107 and P0108, codes for high input and output of the MAP sensor. When i unplug the sensor it seems to have minimal effect to the running condition of the car. When i unplug it at times the car will keep a steady rpm while hitting the gas and the car acts no different when i unplug the sensor when the car is running well. I ordered a new MAP sensor which should arrive today so i can see if that is the problem.
View 4 Replies
I own a stock 2010 golf with 22k miles on it. There seems to be a problem with brake feel. Brake pedal feels way too soft and there is way too much pedal travel for brakes to engage. Car won't start decelerating until pedal is pushed nearly 1/2 of its total travel length. However there seems no problem with stopping the car. On hard braking car stops well (with ABS). Another problem is brake feel isn't linear.
View 10 Replies
It is the 2000 GTP 2 door. It is my sons car and is dead in front of my house. Changed the fuel filter as it is cheap to do. At the check valve there is no pressure in the fuel line. I turned it over with the hose off the filter it did not pump any fuel. I do hear a click or clunk in the gas tank when I turn it over suggesting it is getting power into the pump.
I almost went and bought a pump but do not really want to put the $230 + tax down without checking the resistor after reading around the net.
View 7 Replies
Got Elantra GT 6 month ago. Good car, but it seems I have a very common problem of Elantras - lost of brakes. My car has TCS, but no ABS. It started 4 month ago. Car is fine for several weeks, but then within two days brake pedal getting from bad to worse. My mechanic already replaced master cylinder and right rear caliper. Did not work. Yesterday it was third time when I almost (very soft pedal) lost brakes. Today in Hyundai dealer service they bled the brakes and said "that they hope it will work". Their mechanic found air in both (left and right) rear brake lines. So, my question if I have a leak in, say, left line will it propagate to the right line? I am asking because I do not know the hydraulic schema of the brakes and want to collect as much info as possible.
View 17 Replies
I have a 2001 Dodge Durang. 105k miles.
Brake pedal is real soft goes pretty far down (close to floor) before brakes kick in.
Check front disc pads and rear shoe pads, both look good. Fluid level is good. Bleed brake lines.
Pump brakes up when car is off, pedal is real firm till I turn car on an push on brake pedal right to the floor.
View 4 Replies
I have an 07 v6 SE with 220k on the clock. Recently switched out my rear pads with no problem, but still had a small shake under braking - so tonight we pulled the front wheels off and switched the front pads and rotors out - did an oil change while it was there.
On it's first test drive - there's something wrong. The brake pedal travels all the way to the floor and is SUPER soft. It still stops. If I mash the pedal, the car will come to a sharp stop - testing on some sandy roads, the front brakes are definitely working - but the front pedal travel is WAY more than it was prior to the pad/rotor maintenance.
We ran out of light, so tomorrow we're going to get some new fluids and flush the system in case we got air in it.
View 12 Replies
