Grand AM :: 2003 GT Seems To Hesitate Under 3,000 Rpm - Lack Of Power
Oct 17, 2013
I have a 2003 Grand AM GT 3.4 with 166,000 miles, its hard to explain but will try. When your first taken off the car seems like its holding back, but then once you hit 3,000 rpm's with the gas pedal still pressed the same amount the car takes right off like it has a power band. Same thing regardless happens all the time under 3,000rpm.
Going down the highway at 70 and you start to go up a slight incline, you give it a little gas and you can feel the car having lack of power, then you press a bit more on the gas and it kicks down a gear and goes. Then back in the same situation once back under 3,000 rpm.
The car idles normal, check engine light will come on once in a while, but goes back off before i have a chance to see what code it is. I do notice when the check engine light comes on, you can feel the car lack power for just a second. I just replaced the o2 sensor today thinking it was that.
View 13 Replies
Advertisement
My issue I'm having - 2002 F350 7.3L has an 8 inch bds lift with 37/13.50 tires. I realize these tires are big but... while driving 100kms/hr or 60 miles per hour and I hit the gas the truck barely wants to move (without pulling a load). Thought maybe a turbo but I have no mechanical skills so here I am!
2nd issue, there's a bullydog chip in that truck when I bought it. he said he always ran it on extreme. I found it puffs way to much black when on extreme and on performance it seems a lot better so that's where I have it?.
3rd issue, the transmission gauge on the dash goes into red when climbing up hills ( I live in the rocky mountains so a lot!) but the bullydog chip says the tranny is only at its hottest 140C? I don't believe that's to hot but I do believe my truck is derating a little while the tranny gauge on the dash is in the red? is there any quick fixes out there for these issues.
View 6 Replies
I have a 2003 with 150k miles. My 6.0 has black smoke and can barely crawl up a hill. Dealership is 30 days out for an appt. Air filter, oil change, alternator, and batteries are new. I removed the EGR valve and cleaned, but the valve seat is not perfect. I can see 20 to 30 mil gap around half of the seat. Is this ok or will that little gap cause this?
Hoses all look good. No alarm lights. I have no diagnostic tool but I can use a meter well. It did have an airbag light but I found the fuse missing and replaced it. The air filter alarm switch fell apart but I bypassed it till I get new part. No alarm lights now.
View 14 Replies
Long story short, when going up hill or any incline for the matter it feels like it's struggling and lugging, blowing carbon everywhere. It's an automatic so I yeah can downshift sometimes but even turning overdrive off doesn't work in a lot situations. My EGTs are way too high and I'm not about to tow my project car to OKC unless I get this figured out. I live around Salt Lake City so towing can be hard up surrounding passes. Just cruising to park city at 70mph on I80 up a pretty good incline my EGTs were 1,000. Just driving around the city, some hills I see 700-800 when I'm going 35mph.
At stop lights I'm seeing 400 at idle. My probe on the pyro is going bad starting to flutter but even if I fix that I'm still having issues up hills. Boost is good, up-pipes don't appear to be leaking but fuel pressure is a little low @56 and I know it's not the fpr because I just messed with that yesterday, put a new poppet and oring in, I haven't checked the fuel pump yet or dropped the tank either. If it is in fact fuel pressure related, does it make sense for me to see smoke coming out, wouldn't that indicate too much fuel? I'm lost, it's driving unloaded like I'm pulling an anchor.
Regardless of which spring I put in the frx I get 56psi, even with the black one I may see 58psi but even with 58psi it was still lugging it's butt off up hills and making that terrible drone sound like F you down shift me now.
View 14 Replies
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 Replies
Picked up a second 7.3, just finished installing the new transmission last night, took it on a drive last night, everything was fine.
Went to bring it home last night- and found myself unable to maintain 50-55mph on back roads at 3500 rpm.
At first it almost seemed like I wasn't getting 3rd/4th gear, but upon taking it for a spin with torque pro, I am getting all gears, overdrive works, TC locks- all appears good there. Trans is getting really hot- but I believe I messed up the bypass lines or the bypass valve is not opening correctly- not the biggest concern.
I let the truck cool to more normal operating temps, took it for a spin, same story. I top out flooring it at about 55mph. No fault codes other than my faulty glow plug module. Everything I'm monitoring on torquepro looks fine with the exception of boost. When I floor my other 7.3, I get 15-20 psi, this, I get like.. 4. Unplugged MAP, nothing changed.
Turbo shot? Glogged pipes? These are my first initial thoughts. Let me know if I'm going in the right direction here, I can rebuild a gas motor in my sleep, but diesels are a newer animal to me, I've only had them about 2 months.
View 7 Replies
I have a 2003, 4.6 F-150 with 201,500 miles
I am having some A/C issues. It's just too hot out there.
#1 The truck has a lack of power when I have the A/C on. It feels like it wants to stall out in the lower RPM's. I loose power when I go 65mph+. The truck actually stalled on me yesterday in the parking lot. I turned off the A/C and it ran fine.
#2 I have to go over a 5000ft pass daily, I turn off the A/C when I go over it. Below the pass, the A/C doesn't work well and it's not as cold. But when I get over the pass, the A/C turns very cold. The pass is like a 3-4 mile stretch.
View 2 Replies
I am working on a 97 4.6 with 146k for a friend. It idles rough and seems to lack power (then again a 4.6 lacks power )
Has New:
plugs
wires
coil packs
fuel filter
sea foam intake
sea foam fuel
I have checked:
proper egr function
vacuum leaks
cleaned IAC
steady 17-18 in vac
clean air filter
cats do not seem to be getting too hot.
no codes
KOEO test ok
KOER test ok
The plugs worked some. Dirty MAF, clogged cats??
View 2 Replies
I have a 2003 MCV36R Camry SPortivo, Australian spec. Have owned it for 12 months. Have had power issues.
Replaced:
plugs
fuel filter
O2 sensors (engine)
MAF sensor
Throttle Position Sensor
Have checker EGR valve - all looks good
Have coded OBD II, no codes coming up
Current issues are:
Flat spots from 1000rpm to approx 3000 rpm (esp on gear change from 1st to second)
Once flat spot stop, it powers up enough to throw you back in your seat.
Also, rough running when sitting on constant speed, esp bad between 65-85 Km/h.
Have recently done a 800km trip. half way through, isolated the EGR valve. Running probs have improved greatly, but still lacks power.
View 5 Replies
I have a 2000 7.3 and I have a hypertech Max Energy Programmer set to stage 3 in my truck right now (100 HP). I noticed last night when I was going up hill and had my foot to the floor the truck would hesitate for a minute and then lag before it was would catch up to itself. I did it again on some flat ground and noticed when it did do that my boost gauge would get to 20 and then fall to Zero. If I start out and gradually get to the floor without punching it the truck drive fine. How to fix it?
View 2 Replies
I just bought a 2000 expedition 4.6 EB.. Just like an f150 same principles apply. Here's the issue, it has 284k miles. I realize its probably just tired and worn out but it just doesn't have any torque it seems. If you punch it above 60 it barely creeps up the speedo, my 00 f150 4wd with the same engine about same mileage was way stronger. My only code currently is P1151 dealing with the o2. Plugs are new coils and most all else is probably old. Just wondering if something is wrong and not throwing code or if its just a tired engine in a heavy vehicle?
View 8 Replies
My 2000, F150, 4X4, 4.6V8, five speed manual idles great and sounds great and throwing no codes. It doesn't have a lot of zip, but it really never has, at least since I bought it at almost 60K miles.
I've never towed much of anything with it until recently. I started towing a 6 1/2' X 10' trailer with a 1,600 pound side by side or a 1,300 pound mower with a large grass collector. Both of these loads have lots of wind resistance.
The lack of power is REALLY showing up pulling these loads at highway speed. Sometimes, even on pretty flat ground, the cruise control will hold the throttle on the floor at 60 or 65 MPH and it can't pick up speed.
I have maintained the truck well, but there is something amiss. It is due a fuel filter, so I will change that. I've never replaced the O2 sensors, so I'm considering replacing the front ones.
I am thinking about using a vacuum gauge to see if I can detect plugged cats. As I recall, there are two on each bank. I have a scanner, so I was thinking about monitoring front and rear O2 sensors and see if I can get the 100 degree difference that indicates a properly functioning converter.
I'm thinking of cleaning the throttle body.
Something else that is odd about this truck. Being a stick shift, it does not want to go all the way back down to idle speed unless the vehicle is stopped. For illustration of what I'm saying, you can kick the transmission in neutral and coast, and it will stay above idle speed until the vehicle stops, THEN it will idle down normally. I have always thought that this might be because so few manual transmission trucks were built that this is something in the chip for an automatic that they didn't take out for the manual.
View 14 Replies
Okay, I am having issues with a 1999 F250 XLT 7.3 with diablo programmer. I have searched and searched and have tried everything we could think of and it is a no go. The truck will crank, hesitate to start, start and die, other times it will only crank and not run at all. We can make it stay running by hitting the accelerator. The only code we were getting was the cps code, but that is suspected to be because of the excessive cranking and no start times. Previous to this issue getting this serious it would stall randomly, at idle, going down the road at constant speed, slowing down, or accelerating. We now have code P0231.
Through this we have tried:
IDM
(loaner) ECM
removing Diablo
3 CPS
shaving down CPS
Shimming CPS
IPR
Fuel pump
relay
fuel pump fuse
View 3 Replies
I have a 2001 7.3 with 243k. I think the injectors are shot but other people including a local mechanic say it's not the injectors. What the truck does is smoke white. Sometimes little puffs when accelerating. Sometimes clouds that make the people behind you drop back a 100 feet. I have a ts6 on the truck and that alone with the 243k miles is enough to think its bad injectors. It smoke white. The exhaust is moist to the touch with soot built up like crazy. It doesn't really smell sweet and it's not really blue at all. It's getting horrible mpg. And lacks power. I don't have a high enough psi gauge to test compression. All arrows pointing to injectors?
View 8 Replies
I bought a 2003 Pontiac Grand Am a month ago, I have already replaced the power steering pump, the water pump, plugs and wires, new battery. It was running fine I drove it last night, but the radio has said loc since I bought it. Then today I got in it and tried to start it and it won't start. It turns over like it is going to start but doesn't. I tried the 10 minute reset thing. That didn't work.
View 1 Replies
I was driving and my truck started have lack of power, could barely get going on hills, tons of blue smoke (smelled like diesel) real rough idle. I unplugged injectors and found #5 made no difference. I replaced it today and I can't get it to start. It'll get to 2000+ psi 48v ficm, low pressure oil registers, ficm says its in sync. It will crank and blow a lot of black like its half firing or something. It has even crank to, until it tries to fire. From what I've been reading could it be the ficm? That one circuit is fried?
View 14 Replies
While I'm cursing at highway speed everything is fine. But when u punch it it pass someone it's like I actually slow down, same from a red light. I've got a livewire programmer in it and this problem is somewhat new. It just seems to keep getting worse, I was going up a hill on the interstate this morning and at 2800 rpms I was actually slowing down. I'm not sure if the fuel pump is going out or if the transmission is slipping or what.
View 7 Replies
Blown fuse causing a lack of power to the OBD port?
I just got my Kiwi2 BT OBD2 adapter and was hoping to start diagnosing my truck, but the adapter won't power on while connected to the truck.
I pulled and visually inspected fuse #12, I also verified power to the cigarette lighter plug and the accessory 12v power outlet.
The adapter powered up with no problem when I connected to a co-worker's Tacoma.
View 14 Replies
I have a 2004 f350 with a 03 bullet proofed motor. The truck did not have any power and the turbo wouldn't support until I put a new vgt solenoid in and it ran great for about 3 miles... Stalled doing 65 kinda lacked power while accelerating but got up to speed quick. I pulled over and no start. It is running error code kam on pcm from disconnecting batteries but could this cause the stall and no start? Or should I be looking into icp sensor?
View 2 Replies
Having some problems with an e-350 dying when in gear and rough idle. Truck starts up after it dies. Vehicle acts like it is starving for fuel. I have check fuel pressure after fuel pump and getting 55psi. High oil pressure pump with in normal ranges. Cleaned and checked egr and it was in the closed position. Fuel filters have been changed. Injector buzz test ok.
View 14 Replies
My 2007 6.0 has a really rough (almost 'miss') during cold start up. After 5 seconds or so, it smooths back out and sounds normal. Until gauge reaches normal operating temp - there is a surge/lack of power during light acceleration. I also hear a frequent compressor coming on and running for a while which I am contributing to a possible vacuum leak. Maintenance is always done on time and I've already had a few costly repairs (both internally as well as externally) on the engine. I usually always wait for the glow-plug indicator to turn off before cranking the engine and let it idle for 5-10 minutes prior to driving it. Once the vehicle climbs to normal temp. everything seems to be fine but the compressor still comes back on every so often.IS it worth simply replacing the vacuum canister located behind the passenger side battery - or should I find someone to hook up a diagnostic unit first?
View 5 Replies
