Grand AM :: 2000 2.4L SE - Random Misfire Error Code And Catalytic Converter Gets Hot
Aug 6, 2013
That Car Grand AM 2000 2.4L SE
The current problem with the car is that it is not accelerating fast, for example i would push the petal to the metal and only go 25 mph and my RPM would be 3000-4000. Initial my brother and cousin though it was the Catalytic converter because it was getting hot but that has recently been change along with the fuel filter and spark plugs. but the catalytic converter is still gets red hot so i forbid myself from driving it till i fix what every causing the slow acceleration and the temperature of the Cata when i took the error code think P0300 random misfire to the local Autozone they printed me a long list of things that could be a issue my question is what is the likely culprit so i can fix those 1st before shelling out cash to rebuild a engine. may just have to get rid of it at that point. so i guess what am asking is a list maybe top 10 so i can fix them one by one as my money comes in.
Before the accelerating issue the car would randomly stop when i slowed down or stooped that when i replace the spark plugs.
View 4 Replies
Advertisement
My 2000 Forester has 96,000 miles on it. A few months ago, the CEL came on. At first it would turn off every couple of days but would eventually pop back on. I first thought it was tied to putting gas in the car, now I think it was just a coincidence.
Over the past two months, I have replaced the catalytic converter with a aftermarket piece (done by a mom and pop muffler shop) and replaced the front o2 sensor three times. The first two times, I used Bosch sensors from an auto parts store and had the code cleared. After about 50 miles the CEL came back on. Just yesterday, I picked my car up from the dealership where they installed a Subaru fron o2. After about 30 miles, the light is back on again. Code is P0133 - heated oxygen sensor, bank 1 sensor 1, circuit slow response.
Now, the dealership is suggesting I need to replace the catalytic converter with a Subaru converter before they can source the issue.
View 19 Replies
I was driving along and the engine started missing really bad. The whole car was bouncing around. At first I thought I had a flat, but when I stopped I noticed it was the engine. I checked the error codes and got 16684 and 16686 --- Random/Multiple Cylinder Misfire.
I had a problem recently with the vacuum hose broken and was causing an error code. Replace the hoses and it has been fine. Checked to make sure that the hoses were secure and they are fine. Doesn't seem to me to be related. So many problems for a car with 57,500 miles
View 6 Replies
My car is in the garage, been having a bunch of issues with the check engine light. This is my current problem, Check Engine light is popping up because the catalytic converter is sending an error. However, there is nothing wrong with the converter, it keeps sending the same error. My car has been in the shop for exhaust issues and valve problems, but this has got them stumped.
View 24 Replies
2000 Grand Am GT with 3.4 and 150,000 miles. Car keeps throwing code P304 - cylinder 4 misfire. The main issue is the light and needing to pass emissions test. It has just recently had new plugs, wires, and injector #4.
The fuel pressure regulator was replaced about 3 years ago because it was leaking fuel, enough to smell while driving the car with windows rolled down. Shortly after the fpr was replaced, the acceleration problem seems to have started, either by coincidence, or improper installation. The light/error has been occurring for quite some time, about the past year or two. About a year ago, the car was also throwing a random misfire code. I am not positive if both codes were being thrown at the same time, and when exactly the P304 started.
The crank (or cam) sensor was replaced and worked with the issue for a short while (removed codes/light for maybe a few months?) Before the sensor was replaced, the car would stumble at very slow speeds, 0-10 mph. Also replaced Idle Air Control valve last year. The car would sometimes surge on semi warm starts (not cold, not 190-200) between 500-1000 rpms. The surge would be worse when I had the blower running or the rear defrost on, down to 200 rpms at times.
Currently, the car runs perfectly fine for me, except when trying to accelerate on highway ramps. Its firing somewhat when you step on the pedal, but lags and takes longer than normal to accelerate up to speed for merging with traffic. Drove the car after new injection and said it runs fine while driving, but the misfire seems to be mostly or only occurring at idle.
View 14 Replies
I have a 2000 Impala with a 3800 V6 series 2 with 165,000 miles. The only code I had was a P0300 Multiple random misfire that occured off and on at first, Worse in the city Better on Highway. It would start running on half the cylinders and bogged down, with the check engine light flashing, after getting onto the highway it would straighten itself out at first. I thought i had water in the gas so i ran some heat through it. straightened out for a day then happened again so I thought maybe a should run some premium gas in it, The car ran like total crap until the premium was gone, so i thought maybe it's running too rich, I put 87octane in it and it ran great for a day or two, then it gradually got worse to where it would not straighten up on the highway, tried to die at stoplights and i had to drive it with 2 feet to get it home and park it. I've replaced the battery, spark plugs, wires, ICM checked good, coil packs are good, replaced fuel Pressure regulator, looked for arcing on the spark plug heat shields and it will not start. It turns over but doesn't try to ignite and when I get the slightest rumble of ignition, it backfires up through the manifold and I see a puff of gas or light smoke by the exhaust manifold.
The car had a vacuum leak around the intake manifold cover gasket and a leak on the fuel rail. I pulled the fuel rail off my impala, snugged up the rest of the intake bolts then disassembled the fuel rail, flushed it out and cleaned the injectors the best i could, then reassembled it. before i re-installed the fuel rail I hooked it up to the fuel lines outside of the engine and tried to start the vehicle. all injectors had a nice spray pattern. So i installed the rail and it still didn't start but it had more combustion than before although it's still backfiring like before. Checked the fuel pressure by turning the key on and the fuel pressure went to zero very fast. I blew the rail out with air so to make sure i didn't damage the regulator I replaced it with the old one, ran the test again with same results, so i reinstalled the new regulator. I performed the fuel pressure test a few more times while moving the fuel hoses and when i moved the back supply line the vacuum loss stopped then dropped to zero when i let off of it. So I replaced the fuel line connector and O-rings on the injectors. It no longer has a vacuum leak.
I cleaned the EGR Valve out and had no luck there, then I removed the Idle Air Control Valve-pushed the pintle in, re-ionstalled it and WooHoo! it started! Although it still ran like crap with the same random misfire I was still happy to hear it start.I pulled the plugs on it to do a compression test and all 6 cylinders have between 180-190psi so the engine is in good condition mechanically. I installed new plugs before getting the car restarted and when i removed them for the test they were covered in thick black soot after running for roughly 15 minutes max.
I have (2) 2000 Chevy Impala's so I've swapped sensors from my wifes car to see if it would fix it. I've tested the following MAP, MAF, IAC, coil packs and ECM. None of these made the car change. I believe it is a timing chain because the car has never had a new timing chain and is way overdue, but I haven't had a code for a crankshaft position sensor. Can the timing chain be bad without throwing a code? It's not out of time enough to change the valve timing because I had a good compression test but its not firing right and still has the multiple random misfire. I have not checked or received a trouble code for o2 sensors, crankshaft position sensor or cam sensor. Something has the timing retarded and is dumping extra fuel into the engine because my new plugs looked like they were in the engine for a year.
View 4 Replies
My 2000 Nissan Maxima has a PO430 code for the catalytic converter that has been going on and off for over 1 year now. My ? is, how would I know that the converter needs replacing? Someone said there wouldn't be any smell necessarily, someone else said I would be leaking qts. of oil in between changes and someone else said it would get bad mileage. Each one debunks the others comments etc. Also just for info., this car had the ses light come on at 57K miles, my brother replaced 2 of the O2 sensors and I replaced 2 also, one duplicate one and a mass air flow as well.
View 1 Replies
Does this mean the DPF is shot? I believe its integral with the cat. whats worth checking first?
View 2 Replies
1996 4runner here (187,500miles), with weld in after market cat (on when purchased, with less than 1000 mile on it). started throwing the 420 code beginning of last summer. Replaced both O2 sensors and same results. Was coming on after every 30-40 miles after resetting, replaced wires, plugs, cleaned throttle body started coming on ever 120 miles or so. Now in the middle of winter it has gone 450 miles and still has not come back on?? Does the winter fuel blends in Georgia, or cold more dense air make a difference on cat performance? Still plan to replace it with a direct fit with a warranty but curious if I am overlooking something.
View 6 Replies
It came on 2-3 miles after a cold start. 3.6 with 137,000 miles. What's next? First car I've owned that uses very little oil between oil changes.
View 1 Replies
I have a 2000 Chevy Camaro. Two years ago my catalytic converter went out and I had it replaced. 20,000 miles later my mechanic says that I need to replace it again. Is this accurate? I thought the life of a Catalytic Converter was much longer.
View 2 Replies
Title says it. Cat is done. Threw code p0420 and am experiencing hesitation at WOT. Already replaced my front o2 (cbfa) and now I'm debating whether or not to get a new downpipe. I daily the car and am wondering if keeping the car as is for a while will damage anything. Cts turbo has a sale for a catless downpipe.
View 5 Replies
I have this vehicle, which keeps blowing out the catalytic converter, its been replaced 3 times in the last month, and the mechanic doesnt know why, he refuses to put another one on it, until he figures this out.
View 3 Replies
My husband,who is an engineer and has done all of our car maintenance for decades is stumped by our 2000 Mazda MPV. He replaced the catalytic converter and put every thing back together, but the car won't run. Will start, but dies right away. Took off new cat,and runs with that off, but not sure why it won't run with the cat on.
View 4 Replies
2004 Chrysler Sebring Sedan, 4 cylinder dual-overhead cam. My check engine light came on this morning and the code came out as the catalytic converter. The car seems to be running fine, at least no recent changes. I'm debating replacing this vehicle soon, and I'm wondering if it's worth working on the catalytic converter. I recently replaced the cam shaft position sensor as well.
View 5 Replies
I checked out a 2006 Prius yesterday a guy is selling. It had the CEL on (not sure why somebody would try and sell a car with that, but anyway). He said that it's because they get gas at a station that consistently doesn't tighten the gas cap enough but by the time the tank is down to 1-2 bars the light always goes away. Although I don't doubt his story, I absolutely doubted the cause. So I took it to get the code pulled and it was P0420, which is catalytic converter threshold below efficiency.
View 15 Replies
I own a 2000 E 250 Econoline van with 170,000 miles. I've been encountering loss of power on acceleration for months. Terrible gas mileage (8-10 mpg) and just recently, I get that rotten egg smell when I gun it and and travel above 65/70. I can feel heat from under the van when i step out as well. I've been blowing individual coil packs every other month after a long drive with a lot of inclines. It all points to a clogged catalytic converter. This van has 3. A front left and right by the manifolds, and a large one before the muffler. My question is, what causes them to go bad? I want to fix the cause before spend the money on new cats. Ive heard a rich fuel mixture could do it. Are there sensors that need to be changed?
View 1 Replies
So the code reads "warm up catalytic converter efficiency below threshold (bank1)" ?? What it could be?
View 12 Replies
2010 f150 with 5.4 catalytic converter. Engine light has been going on and off for the past couple of months. Had the code read and its says bank one catalytic converter. Ford dealer said to replace the 02 sensors. Had that done but light still comes on and off with same code. Could there be something wrong with the sensor or should I just have the CC replaced also. I just don't understand why it would come on for a few days and then not come on for a few days if its the CC?
View 1 Replies
My check engine light has been coming on and off and it seems to show P0420 for catalytic converter. The light stays off for about a week and it'll come on for a day or two and off again.
Wouldn't a failed converter stay failed? Can P0420 be triggered by loose/bad gas caps?
View 3 Replies
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
View 13 Replies
