Leaking intake manifold gaskets on General Motors 3.1L V6 engines? Mine is a 1998 Grand Am with low milage (40K) and I have been told I need to spend $900 to replace the intake manifold gasket because it is leaking antifreeze into the engine oil.
View 8 Repliesso new motor new intake , rear passenger side decides to leak when roughly about 10 degrese or lower and being -13 yesterday and-18 this morning.
last year it did this n i put a nother hose clamp on that rear tube and just happened to stop . n now back but the ting is that its not wet at all at the hose but at top of head bottom intake hmm . this is all just during the initial start of truck stops even before truck really gets warm
if i tke it off n its messed up i hope its warrentied even though i painted it. if fine i guess add some gasket maker ?
On a 1997 Nissan pickup 241,000 mile 2.4 liter. What are the signs of a bad manifold gasket. How can i test it.
View 6 RepliesI have a 2000 Pontiac Grand Am SE sedan (base model) with a 3.4L engine at 142Kmi that was just diagnosed with an intake manifold coolant leak by an independent shop.
I've done some googling and found that this is a known problem with this engine (including a class action suit). So far the leak is just external; no coolant in the oil and no oil in the coolant.
I took my Monte in for the annual Missouri Safety Inspection. Note: I had no known problems with my 2003 Monte SS 117K Miles. After the inspection, which passed, I was informed of a variety of problems: Intake Manifold Gasket Replacement, Valve Cover Gasket w/Intake replacement, Thermostat w/Intake Removal, Fuel Injector O-Rings w/Intake Removal.
My question is should I have all of this done? It's not cheap..roughly 1000 bucks. I know very little about this and I don't want to just tell my mechanic to do it without some research. Are these common problems with Monte's of this age/mileage and just part of the cost of owning this car. I am the original owner and have avoiding costly repairs/maintenance..it's been a great car.
I've got a 1997 F150 with the 4.2L V6. Before I got it last summer I did some research, but apparently missed the issue with the intake manifold gasket leaks on these early engines. It seems to be a very slow leak, but obviously I want to get it fixed. I called Ford to see if it had had the recall work done on it, but all they could tell me is that there wasn't an open recall on my truck (with the exception of the recent fuel tank strap recall). Their system apparently only goes back 10 years, so they couldn't even see the freakin' recall. So, I've got a few questions:
1) I know I didn't post much info, but does this seem like an intake manifold leak?
2) Are there any special tools needed to change out the gasket myself?
3) Can you all recommend any replacement gaskets? I found a few different manufacturers of gaskets, but I'm sure some are better than others.
4) Can this issue cause the computer to throw the loose gas cap code (P0455 if I recall correctly).
5) Would it be worth it to just get a new truck? I really wanted a diesel in the first place, but I also hate to give up on a nice truck with only 115,000 miles.
I have a fudged-up looking oil leak that my oil change guy says is probably a blown intake manifold gasket. Is this the same as a head gasket? I thought a head gasket was around the pistons. I see there is a product on the market that you can put into your radiator that plugs up leaks in the head gasket (Steel something). Is this an OK fix? It would cost $90 for a bottle of the stuff. And what is a reasonable, or low, rate to replace this gasket? And, how long can I drive the car with this condition? It has lost a quart of oil in the past month, driving about 600 miles.
View 3 Repliesjust got finished putting her back together from a blown intake manifold gasket and run for a few miles to get rid of any cob webs and then my battery light comes on. just replaced the battery last week. and I tested the alternator and it charging at 14.5 volts bat reads when disconnected 12.9 volts so I am not sure why my battery light will come on.
View 14 RepliesI have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 RepliesI needed to replace the intake manifold gasket on my 2002 f250 v10. Tore everything apart put the new gasket in which was the same as the old one lyrics to notice something isn't right. I have been driving the truck for over 10 years like this. Is it OK to just continue bolting everything down and go on like this? I am guessing the prior owner 10 plus years ago put the wrong intake on. I keep looking up intakes but they all look just like the one I have. Also that port exposed is on the back passenger side.
View 3 RepliesI've currently have 114,000 miles on this Pontiac Bonneville and I replaced the intake manifold last summer. Recently, I have been having issues with the intake manifold leaking a fluid on the right side of it (facing the engine) and been having dirt or some other type of fluid mixing in my fluid tank. The leak has been causing some smoking issues. Also, when I start the car in the morning white smoke comes out of the back of it. Where I need to start so that I can get this fixed. I'm assuming something went wrong in the replacement.
View 6 RepliesI have 98 windstar, p1538 code, IMRC. I have physically checked both IMRC's and they are functioning as they should. (if they were bad, they would not move at all right?) Assuming they are good, which step in the troubleshooting process I go to now? The van runs perfect, just that darn light! Do I start going for the O2 sensor now? What to next in the chain of troubleshooting?
View 14 RepliesI have a 98 f150 4.6 4x4 with 175.000 miles, I suspected the intake gasket is leaking, I'v never done this before. What is involved with this type of repair? Will the intake gasket leak bad enough to leak antifreeze on the floor? Is it okay to continue to drive with this problem? Bad weather is on the way.
View 7 RepliesI have a 01 vr6 mk4 gti. When I bought the car I noticed a rattle but never paid mind to it. But now I just want it fixed. I hear the rattle come from the back of the engine near the intake manifold when I rev it a little. The most rpms the louder the rattle . I been doing some research and came to a conclusion that it could be the shift rod and bad intake bushing. But, I'll like a link on how to replace the shift rod.
View 5 RepliesLooking at a 2003 Prius with 77K miles. Turn the key, the engine starts, runs smooth for about 5-7 seconds. After that it starts to run rough and rattle, then shuts off. The only code I pulled was P3191. I pulled off the air cleaner to clean the throttle body, and noticed a small pool of oil in the bottom of the intake manifold. Is that normal, or could that be causing the code issue? BTW, I cleaned the MAF and throttle body, and the engine still does the same thing.
View 14 RepliesI have a 1998 chevy silverado z/71 4x4. I had a water leak and had the intake manifold gaskets replaced. Ever since then, the check engine light comes on and it soots up the o2 sensors and the 4 plugs on the right bank. It may run good for a month or so and then it starts all over again.
View 1 RepliesI'm getting oil and fuel into the intake manifold every couple hundred miles. Oil level is in the middle of low and full mark. It's not like it's a huge amount of oil and fuel in the intake but it's enough to make the car misfire, bog out. Only codes I'm getting are misfire codes for all cylinder and reduce engine power code (forgot what code it actually is) but that's when the car completely shuts down and won't start with red triangle light. If I clean the intake out and unplug the battery for a few min I'm able to start the car again, but it will run really rough and white smoke will start to come out the exhaust (gas smell). I'm wondering if a bad maf would cause this. I've already cleaned it but still doing same thing. Don't really know what the specs or reading the bad is suppose to be so I'm kinda stuck to determined if I need a maf or not. Cars got about 242K miles.
View 17 RepliesI have a 1999 Ford Expedition. A couple of days ago The engine started losing coolant as soon as the engine cooled. I replaced the coolant only to lose it again when the engine cooled. I was told that it is more likely the intake manifold gaskets leaking. It seems they are right. What is the cost to repair if I take it to a mechanic?
View 1 RepliesMy 1998 Grand Am (2.4L)radiator fan keeps running after I shut the engine off. This is after a short drive of ten minutes. Both times it did it, it was not an unusually hot day and stopped after I started and turned off the engine again. I have owned the car 7 years and it has never done this before.
View 1 RepliesI replaced a battery on a 1998 jeep grand Cherokee v6. It started and ran fine, but then in my infinite wisdom, I decided to remove the negative battery cable with the engine running to test the alternator. Some smoke started coming from the back of the engine, so I immediately killed it. It wasn't running for more than 5 seconds. When I started it again, it faltered, but the second time it started fine and ran fine, a little more smoke came out but stopped soon. it smelled like burning oil. We drove it around the block with no problems. I know it wasn't the alternator that was smoking because that's not where it was coming from, and I doubt it was the ecu because then it wouldn't run.
View 3 RepliesI'm trying to chase down the cause of a P0420 code and make sure there isn't anything else causing it before I take the rather hefty financial hit of replacing the cat. Since it's the first Prius I've ever even been around when running I can't tell if its exhaust makes more noise than it should, but it has always seemed to me that it makes more noise up near the engine than it should, so I'm planning (well, 'fogging' is probably more accurate given my plan...) on smoking the intake and exhaust. The intake is fairly easy- but the exhaust, the exhaust manifold is rather buried. Do I just need to take the cowling off so I can look down at it and see if it's leaking anywhere? I'm assuming I won't be able to see it completely from just down below it...
View 3 Replies