I just bought a 2012 R last friday. 14k on the odometer.
Car is perfect, cept when i shift into 6th its really grabby with a grind. does it every time.
should I take the car in to have it checked out, is this normal?
Last week my wife's 2004 Santa Fe with 68k went into limp mode, when I ran the code reader it came up with throttle position sensor and pedal position sensor. After fixing both the car runs great except for a Grabby or sudden shift from 2nd to 3rd. It shifts at about the right rpm but very hard. I am wondering if there is trans codes that need to be reset that my code reader is not able to do.
View 3 RepliesI have an 04' R32 with about 56k on it. Here's the problem; when I drive it hard and speed shift from 2nd to 3rd it grinds just a little. It doesn't do it when I'm just cruisen grany shifting. For awhile now I've been thinking that the synchronous from 2nd to 3rd gear was going bad, till I talked to a friend with a 20th GTI who said that the 6 speed trannies will start to do that, and there's really nothing you can do about it. Is this true that I just have to deal with it or can it be fixed?
View 12 RepliesRecently bought a 1999.5 vr6 jetta and noticed that it will randomly grind going from 1st to 2nd gear (its a manual). It seems really erratic, it will do it at any rpms and at completely random times.
It only does it when shifting up, not downshifting. I can also go 50 times or more shifting into 2nd without it happening or it can happen 5 times in a row. Not sure what do here...
On my 2011 Prius Four, the brakes are VERY sensitive and bordering on "grabby" when in reverse gear. I don't know if that is common or if I should have it worked on by dealer. Brakes are fine in forward gear.
View 8 RepliesI noticed through careful investigation that my 03 GTI 1.8T (180,000 KM's or 111,850 miles) will grind 3rd when in these conditions:
1. When the car has been driving for more then half an hour and everything is hot
2. When the car is over 2800 RPM's while hot (ie. getting on a highway)
Now I know lot's of people blame syncro's and yes I could see that my car has had 8 previous owners so I can't say they all shifted perfect. But what I do know is that when I downshift from either 4th or Neutral it will never grind even when I don't Rev Match or "Blip" the throttle. So it can't be syncro's in my opinion.
So what I've done to the car to rule out some problems were:
- Change the gear oil from what ever it was before to Royal Purple 75W-90 (NO luck.)
- Then I added a short shifter and adjusted my cables properly (still No luck)
- Finally I noticed my shifter was sloppy and one of my bushings were torn so I bought 42 DD's metal bushings and the shifter did stiffen up a lot, however!!! (No luck)
I know it's not my driving technique because I watch my foot depress the clutch fully and then I gently push it into third. I also know I'm shifting correctly because I can double clutch and normally shift through every other gear properly without any grinds or clunks. Just the devilish 3rd gear.
I would like to hear the solution. I'm going to change the oil one more time to Redline MT-90 and see how that goes, but if that doesn't work I might just tear apart or get a new tranny.
So i was trying to adjust my freinds shift linkage on his o2j and i got a little ahead of myself and forgot to put the shift tower in the home position before making the adjustment. after i realized you can't shift into second ( either that or 2nd and 4th are extremely close together now and feel like the same gear ). I try to get it in home position even with the cables off ( did this for experimentation) and still wouldn't go into home position...meh. still have all the other gears including reverse .
View 4 RepliesBackground facts:
Tranny swapped from my 4 speed auto to a 1.8t o2j 5spd
13lb. Light flywheel
Powerflex dogbone mounts
Peloquin LSD
The problem: Very hard to get a smooth shift from gear to gear. Trust me, I know how to drive, but I can always feel the car shifting into a different gear if you know what I'm saying. On my friend's bone stock Jetta, I just let the clutch out without gas in between shifts and you don't feel a thing.
On my car, you feel EVERYTHING. People have told me the light flywheel will make the ride more uncomfortable in many ways, especially since the RPMs drop much quicker in between shifts than stock.
I have a 2003 screw 4x2 with the 4.6, 148,000 miles, and I'm not sure what kind of transmission. Recently when the truck would shift into second it would hesitate and I would feel a slight grind, but it only did it when it would shift at 2000 rpm, if it shifted at 2500 rpm it would shift fine. I checked the fluid level, it was full, it smelled okay, looked *fine.
After pulling a boat (19 foot bass boat...nothing too heavy) it started to shake violently when I'd take off from a red light. So I dropped the pan and changed the filter, The fluid was dark red and smelled a little burnt. I put 4qts of fluid in it along with some Lucas transmission fix. The shake during take off is gone, and the grinding while shifting into second got a lot better but didn't go away completely.
However, now the grinding into second has has gotten worse again, and if I make a right turn from a red light it grinds and feels like its slipping until it shifts. I am not sure why making a right turn would affect it but its definitely worse when i turn right, left turns are fine. I'm guessing my transmission is going out and I just need to get it rebuilt...
Just within the last 1000 miles my MINI has been randomly grinding into second gear (6 Speed Getrag Manual for the Cooper S) when turning right. It is a little notchy when traveling straight and beautifully smooth when turning left. When pulling out of my garage the other morning I went into second but purposely pulled the gear stick towards the right side of the gate and it did the same grinding thing that it does when going around right hand turns. It seems as though something is out of alignment? It feels like the shift linkage is not properly placing the internals of the transmission. It happens mostly when cold and once warm the random harsh grinding stops and it goes to simply really notchy.
View 12 RepliesOk, I'm finally ready to dump out this stock tranny fluid and put in something else to alleviate the 3rd gear grind. Question is, which one should I put in?
View 18 RepliesI have a 1986 Ford Bronco straight six 300 4 speed manual NP 435
She grinded a bit when shifting from a stand still but nothing terrible for an old rig but leaked oil bad from the rear main seal so I took out the tranny/t case to put in new clutch, throw out bearing, pilot bearing, and rear main seal. When I put it all back together shifting into 1st would grind like CRAZY. So would reverse but not near as bad. So I took it all back apart inspected everything even torqued the clutch to specification. Put it back together and same result. So I replaced the slave/master cylinder thinking the clutch wasn't pushing enough bench bled it and still no luck.
I just got my 03 F-150 with 112k on the clock. It has the manual 5 speed tranny behind the 4.6L.
However, since I've gotten the truck, it's kind of difficult to put in first gear. If you are sitting at a light and in neutral and the light changes and you push the clutch to the floor and put it in 1st (fairly quickly - a normal reaction time), it will actually do a little grind and/or thump. However, if push the clutch to the floor and wait a couple of seconds and then shift into first, it's a bit of a "push" but it will go in without grinding.
Once in a while shifting to 3rd it feels the same way, but won't really grind.
I'm just wondering if that means the clutch is toast or is it the trans that is toast? Reason I ask is my 96 Cobra with the T-45 5 speed would grind going into 5th gear if I just normally put it in. I used to have to put it in neutral and then push the clutch in again and slowly shift to 5th for it not to grind. And it wouldn't go into 3rd if I tried to shift fast or under power. I replaced the clutch and found out the trans was actually going bad, but it had 173k on the clock.
So, I'm really paranoid that it's my darn trans in the truck instead of just the clutch. Whenever my old Camaro clutches used to be dying, they would slip more than they would ever grind going into a gear.
Last night, on my way home, I suffered a catastrophic transmission failure in my 1991 2.3L 5 speed. Stepped on the clutch on an exit ramp from the freeway and was rewarded by a LOUD screech/grind, a stopped vehicle, and a transmission "locked" in 5th gear. The local HERO service pushed me out of traffic and I got towed home. Looks like a transmission transplant is in my immediate future. So - the question is, what year manual transmissions match up to a 1991 2.3L 4 cylinder, standard cab, 2WD? I need to start searching salvage yards.
View 3 RepliesWell here it is I just put a new slave cylinder in my 02' F-150 and once we figured out all the little issues we were having we finally got the truck to fire up!!! Now my problem is that when the truck is running I can't get the truck into gear with the clutch pushed and it doesn't even grind. But when the truck is off it goes through the gears no problem what so ever. When we did the slave cylinder while we were in there we just replaced everything clutch, pressure plate, flywheel, rear seal, and pilot bearing. We figured that since all the shops were quoting me 800 and up for just doing the slave that since were in there we might as well do everything since nothing has ever been replaced yet. My question is why will the truck not let me shift into gears when running but no problem when off. Oh and yes the system was bled after doing the slave actually twice so far.
View 5 RepliesSo my MK7 GTI is my first manual car...And I am having trouble doing slow speed maneuver most of the time...
I often found myself in a situation where the speed and the rpm of the car is too low for 2nd gear, and when I try to shift to first, it would't let me, unless I almost come to a complete stop....
I tried to press the clutch all the way in, then rev up the rpm, then release the clutch, but it doesn't work much, the car still jerks...
So, in the last month or so I have been having trouble getting the car to go into second gear when mashing the go pedal. I have to try several times and seems to be that the car has to unload and then it will shift.
I am using the DG shifter and have been for 30k+ miles and I have the red HPA dogbone insert. The shift has not been a problem up until the last month or two.
Is it time for motor mounts?
When I shift from first to second gear, especially when the car is still cold, I get a vibration(?) feeling through the shifter. I'm not shifting hard but not slow either. It's definitely not a grind but it only happens when shifting from first to second.
FYI- The car has ~550 miles on it.
I just finished the DG install yesterday. I am having a real problem with the first gear: it is really hard to shift into it (I mean hard!) - and several times I went into 3rd believing it was in 1st, while driving. I know that the DG is notchy and a little stiffer (which I like) but this does not feel right. I have to really push hard (moving slightly toward reverse) to shift into 1st. My wife would never be able to find it or shift into it (not that I let her drive my R that much...).
Note that all the other gears (2,3,4,5,6 and reverse) shift beautifully without any effort with that nice click. But not 1st.
What is it? Adjustment? I did it twice. I made sure that both cables were "all the way in" before tightening the first two bolts (and I made sure that the cables were not moving - a common problem with this install) with the engine lock on and pin in.
2011 TDi 6 Speed (Sportwagon) with problems shifting into 2nd? Mine is currently in the shop under investigation for a balky shift when cold. The tech says it's not right, but then they find another vehicle in inventory with the same issue...currently waiting on a VW engineer.
View 16 RepliesSo after my 500 mile break in I decide to see what my new set up is made of. Had the kinetics stage 3 and the south bend stage 3 clutch installed. Did my first launch...everything went great. Got just a little bit of spin and the car took off like a scud missile. Right as Im going to shift into second my Rpms go down fast. No weird noises no metallic sounds nothing. No fluid under the car. Only a slight clutch smell nothing crazy. Car wouldn't go into gear. Shut the car off and it goes into gear.
View 20 Replies