Golf VI R :: LED Tails Without Fog Installed / Now Right Front DRL Not Working
Jun 20, 2012
I have changed byte 18 to 04 ROW, which cleared the tail light codes, but now the front right DRL does not work.
View 6 Replies
Jun 20, 2012
Advertisement
Golf V R32 :: LED Tails - Moisture On Inside Of Each Corner Light Lens
This is the first winter with my LED tails installed, and notice that I get varying amounts of moisture on the inside of each corner light lens. It makes me a bit worried that this will eventually cause a short or destroy a light in my not-so-cheap tails.
It comes and goes based on relative humidity, temp, and precipitation - but isn't necessarily worse when raining. It's almost like the larger the delta between a higher cabin temp and colder outside temp on a "humid" day generates the most moisture.
I have checked the "bulb access" on each corner and the weatherstripping is intact and appears to make solid contact when tightened down.
Golf IV / Jetta IV :: Switched Out Tails, Now Reverse Lights Do Not Work
Went from this
to this
But now for some reason both of my reverse lights aren't working...
Since my first post the jetta has come a long way. still has a longer way to go.
Golf/GTI VI :: Euro LED Tails With Fogs - Reverse Lights Throwing Error
Had the tail lights coded for at a local shop.. realized as I was leaving that the reverse lights are throwing an error. Can these be coded for? Now that the car recognizes the tails as LED, is the error coming from the incandescent? Should I replace the bulbs with low pulling LEDs without resistors? As for the fog, do I have to replace the bulb as well? No euro switch or wiring done. Basically, how do I get rid of the error.
View 3 RepliesPrius (2010-12) :: Installed LEDs Now Lights Stopped Working
I replaced all the interior halogen lights, parking lights and license plate lights with cool white LEDs. They look good and all was fine until the last step while installing the license plate lights. I plugged one side then turn the light switch on to verify the polarity to see if bulb would come on which it did. Same process for the second license plate light but this time around after turning on the light switch to see if it was plugged in right, I noticed the brake lights didn't come on. So I flipped the switch around a few times and nothing. Now the DRLs do not come on either as well as the parking lights. The only lights that work now are the head lights and interior lights. What happened how do I fix???
View 10 RepliesFord F-150 (2004-2008) :: A/C Not Working After Control Panel Installed?
I just installed a Heater AC Control panel that was broken when things shifted in my truck. Now, air blows, but I get no AC. I'm wondering if something deeper in the dash was broken.
View 1 RepliesFord Fuel System :: Installed Holley 4 Barrel Installed But Won't Run - Carburetor?
i just got my edelbrock performer rpm intake and my holley 4 barrel installed but it won't run...the only way i can get it to hit and run at all is to floor it like it's flooded...then it'll run for a second but will never rev up and get going like it should...so i watched some vids on youtube for setting mixture on holley's wich i was pretty sure about anyway...turned the idle mixture screws in to snug and then out 1 and a half turns. is this a symptom of a bad vacuum leak or is it something to do with the carb maybe not enough fuel?
it's a holley 4160...list-6619...which is 600 cfm...it's on a 302 with 3 speed.
Passat (B6) :: Moisture In Back Up Lights - Tails Don't Fade?
I noticed I have moisture in both my tail lights and a little in my back up lights. what's the best course of action to deal with this so my tails don't fade? I'm hoping I won't have to take the tails apart.
View 4 RepliesTiguan :: Front End Is Different From The Actual Unit Installed
Noticed that the front end (front lower skid plate) is different from the actual unit installed on the vehicle when compared to the pictures. The skid plate in the pics look much nicer and is larger and extends higher up towards the top of the lower part of the front bumper. [URL]........
View 2 RepliesIS F (2008-2014) :: Power Windows Stop Working After LED Headlights Installed
I don't know what's going on with my power windows control on the driver door. Auto up/down function is not working. It cannot roll passenger windows up or down. I checked the other 3 doors and the switches worked. I don't know where to look!
View 8 RepliesFord 6.0L Power Stroke Diesel :: Installed SCT Tuner 3 Injector Not Working?
I installed a sct tuner on my truck and used the default street flash and my #3 injector promptly took a dump. Will a tuner kill injectors?
I just finished up oil cooler rebuild studs, blue spring and egr delete.
Now it looks like i have more injectors going bad.
I have 147,000 miles on the truck.
Touareg :: Check Lights Warning After Installing Smoked Tails
Just installed the smoked tail lights on my '07 Treg. Installation was very easy per the instructions on OEMplus. I did a great job from that standpoint.
Got one issue, I check the 'Check Lights" warning and I think its due to the fact I tested the lights before I had all the new ones installed and hooked up. Do I need to take it to the dealer to have something reset via a computer or will the check light go away with some driving, which is what the dealer said.
Subaru - Outback :: Interior Lights Not Working And Clock Resets After CD Player Installed
My brother installed a CD player in my car a while back and did something wrong. The interior lights don't work anymore, the clock on the dash resets to 1 o'clock when the car is shut off and the driven miles reset every time as well. I have checked all the fuses and they are good. Someone went in and looked at the wires behind the CD player and they didn't see anything wrong. What could cause this issue? (Subaru Outback 2000)
View 2 RepliesSonata I45 (YF - 2011+) :: HIDs Installed, Driver Side Bulb Not Working After One Hour Of Use
Well, was excited to finally get these things installed and they looked and were working perfectly. Unfortunately after one hour of use, whilst pulling into the garage, the drivers side bulb just cuts out completely. Check all the wiring everything is good, the passenger side is still working perfectly, so I need to determine what the problem would be, because I pulled out the bulb and it is completely in tact.
View 19 RepliesGolf V R32 :: Front Charger Not Working
Have a problem with their front 12V charger not working? Could this be a fuse issue? I couldn't find the specific fuse location in the manual for the front charger.
View 2 RepliesFord Ranger / B-Series :: Installed All Lights But Front Signal Won't Work With Headlights On?
Problem with 1157 LED bulbs . I install all 4 light bulbs the tail lights and front turn signal lights the problem is all lights work with the signal lights. but when I turn the head lights the front signal lights don't work. Also the turn signal lights on my dash board both light come on
One more thing if I install the regular 1157 on the front . the LED lights on the back work fine and the from work fine . looks like the front don't like the LED bulbs. I have 87 ranger cab and half or extended cab. v6 2.9
Golf IV R32 :: Front Driver Side Headlight And Taillight Not Working
So sometimes my front drivers headlight and drivers taillight decides not to work. Sometimes one will work and the other wont and other times they all will be working fine. I've checked the fuses and the bulbs and they both are fine.
View 10 RepliesGolf/GTI VI :: Installed GTI Sway Bar - Getting Clunking Noise
So I recently installed a GTI sway bar on my 2010 TDi and was getting a clunking noise. I assumed that it would be the subframe making noise since I've read a lot about that but the sway bar is actually rubbing on the front portion of subframe (the part that bolts to the frame directly above the A-arm). It's hardly touching it but its enough to wear into the bar.
View 4 RepliesGolf IV / Jetta IV :: Stereo Needed To Be Installed
I have a touchscreen that the dealership provided me but with the catch that I've got to install it myself, pretty sure it has something to do with the state the previous stereo was taken out, all I'm left with are a cluster of wires none of which I know are for what.
View 2 RepliesGolf IV R32 :: Idle Vibration After New Axles Installed
I just had both axle's replaced. Looked for OEM but couldn't find availability so I went with FAQ. Just had a local shop do the work. When I got my car back I've noticed that at idle I can feel some vibration. The noise is really subtle but if I rest my foot on the pedals I can feel it through the pedal. I'd describe it as a revolving sound, almost like it's coming from moving parts, although I'm at idle.
View 3 RepliesGolf V R32 :: RNS510 Installed Now No Radio Info In MFD
I installed a RNS510. When I scroll thru the MFD there is no info for the radio as if it was off.
View 14 Replies