I had to make a panic stop from 80 mph to complete stop to avoid a chain accident on the highway this morning. After I stopped I noticed that my hazard lights were activated. There was no way anything could have pushed the button. They just turned off when I pushed the button and that was it.
View 7 RepliesHave a quick question about no blinkers/hazard light working. I switched out the hazard switch with a working one from my MKIV 2.0 slow and my GTI's hazards and blinkers still didn't work. Going to check my fuses once I step outside but is there anything else I can troubleshoot immediately besides the two obvious solutions I'm about to attempt? (MKIV BDF VR6 2003)
View 9 RepliesMy hazard, reverse don't work. The over all instruments panel light doesn't light up (the small bulbs work). Gauges with needles work. I'm putting every thing back into the truck. I left the steering wheel resting on the floor while cleaning and also left the wiring in. Everything else came out because I had to clean out the smell of mice. After I installed the instrument panel I started the truck, there was no hazard lights. I checked all the fuses under the dash. I checked all the fuses under the hood.
I did have a bent brake plug blade to bend straight. I need to replace a bad key cylinder, you can turn it without a key. I believe there were three plugs I unplug to lower the steering wheel. Park brake, brake pedal and a plug under the steering wheel. Wipers, interior ceiling light work. I believe there's a switch on the column (?) that includes the wiper arm. Should it also operate the hazard lights ? The steering column is installed, I can drive it around. Outside cargo lights won't go off, even with the light switch pushed in. Everything worked before.
I have a 2004 F150 XLT and the passenger side tail light doesn't work whatsoever. The light does work for hazards, turn signal, or when braking. The passenger front turn signal works, so does the front and the driver sides tail light. Only the 1 tail light doesn't work. I bought a new brake light bulb and it didnt't fix it, so i swapped the drivers and passengers bulbs out, and it still didn't work. I replaced the 10 amp fuse (#36) in the fuse box. What is causing the problem.
View 2 RepliesDrivers side turn signal does not work, and blinks fast when turned on. The brake light on that side and hazards do not work. when I unlock the car with the remote, it lights up fine.
View 5 RepliesI have a unique problem with my newly acquired 71 F250. The left brake does illuminate when the brake is pressed but when the right turn signal if activated the left brake light does come on. The left flasher light also does not work. All other rear ligh function are normal. I am assuming I have a short or a wiring issue just wanted to know if there was any common item that might be know about this topic. The bulbs are all new. The reverse lights do not work either but pretty for sure its unrelated.
View 2 RepliesPassengers side tail light doesn't react when braking, using hazards or blinker, what do I replace? The bulb is lit, but doesn't blink or brighten when the brakes are applied. As of right now I'm replacing the bulb socket seeing as when I replaced the bulb the contacts were covered in a brown crust, is there something else I should be looking at?
View 3 RepliesWondering if there is a relay for directional and hazards that would die.... I can see that the indicators in the speed/RPM gauge set do light up ever so weakly when I press the levers/button, but no power to the actual bulbs. Where is this relay/fuse?
View 2 RepliesIn my 97 Ford Taurus the turn signals and hazards are not working. I changed the fuses, but still no luck. Someone mentioned that there might be another fuse box under the hood (besides the maxi fuse box). Also someone mentioned the blinker fluid being low.
View 14 RepliesI recently purchased a 2009 elantra and the hazards dont work but both blinkers do I need to get it inspected but it won't pass without hazard lights.
View 14 RepliesA friend of mine has a 99 passat. Driving home, his turning signals and blinkers stopped working. The lights work with the alarm though. The fuse was fine. Is there a relay that craps out on these cars?
View 3 RepliesOur Phaeton has a had a problem with the radar unit and was the electronics where repaired. According to the repair people it now has to we reactivated in the car but we are not managing to achieve this with VCDS. We have tried the following codes:
Code:
Select 01 (Engine Electronics)Security Access -> Function 11 (Codierung II) ACC = Adaptive Cruise ControlCCS = Cruise Control System (Normaler Tempomat) ACC/CCS-Deactivation Code: 16167 (first deactivate, than continue)ACC-Activation Code: 13647 (Possible also 13377 or 30903)CCS-Activation Code: 11463
The codes are accepted by VCDS, but nothing changes.
Also, additionally the warning for engine fault has gone on. Is it possible to disable this warning? We tried code 30903 but it isn't accepted.
[Code] ....
Today after leaving office I switched on the ignition and for the first time I see this massage "Immobilizer activated". I went out to look at the car and found some finger prints on the driver side window.
Is the car so sensitive to touch? Or the alarm was activated for some reason and some one tried to look inside the car?
2004 Prius here. The turn signals and hazard lights stopped working a few days ago. I found a disconnection in the grounding and repaired it. Also replaced the fuse and the flasher switch. Now the lights work, and I can hear the flasher switch clicking, but they don't blink!
View 13 RepliesI used the volt meter wrong while testing my turn signal bulbs for power and not they do not work (or hazard lights).
View 3 RepliesToday, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.
After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.
I had to jump start the truck this morning and after I drove to work and turned it off, the hazards won't stop blinking. I disconnected the battery so to not drain it. I later when to battery warehouse who tested the battery and said it was find and determined I had a loose connection on my terminal. said I need to fully charge the battery. went back to work and turned it off, everything was okay for a while but then the hazards started flashing on their own again.
Lexus said that a low battery is probably tripping the alarm and I just need a new battery. Does this make sense? I can put in on a charger when I get home tonight.
I've just acquired a 2008 Cranberry T'reg V8 with the Techno and Lux packages. Whenever any function on the Nav/Radio unit is activated, the radio turns on. For example, when shifting into reverse, this activates the reverse camera screen -- and the radio also turns on. Likewise, if I turn on the navigation screen, the radio turns on. This is kind of annoying if I don't want the radio on, but want other functions activated. Is there a setting that I'm missing? The only thing I can figure is to keep the volume setting at zero.
View 2 RepliesI have a new dog which I need to leave in the car occasionally (not when it is sunny etc). Is it possible to lock the santa fe 2010 without the sensors activated so the dog doesn't set the alarm off when moving around in the boot. I just tried locking the car using the key but it didn't do anything but I can unlock with the key!
View 4 RepliesDo the taillights are supposed to come on during the daytime when the DRL's are activated? Mine do and I'm trying to figure out if I have a bad light sensor.
View 10 RepliesI recently bought an 08 Sonata from a used car dealer which has 65,xxx miles. Last week my turn signals would work intermittently, and now neither the turn signals or the hazards work. I put in a new relay and a new turn signal switch, to no avail. When I turn the hazards on, the relay clicks once then nothing. When I do the turn signals, nothing clicks. Is there another relay I'm missing somewhere?
View 14 Replies