Golf VI R :: Dropping Revs And Stalling When Pushed The Clutch In
Feb 22, 2015
About 2-3 months ago I noticed that whenever I would push the clutch in and let the revs drop, they would drop below the 800 rpm mark and the car would automatically rev them back up to prevent from stalling. This usually happens when I am slowing to come to a stop, like coming down an off-ramp or to a stop light. Then one night after a 45 minute steady speed highway drive, I pushed the clutch in, shifted to neutral and let the clutch out and coasted to a stop. As the revs dropped, the engine stalled completely and the red alternator warning light came on. While still rolling on the highway, I pushed and held the start/stop button and it immediately started back up.
Over the last 6 weeks, this has become more frequently. It is now at a point where the revs will pretty much always drop below 800 rpm when I slow down and the car usually revs them back. However, I have had six more stall episodes like the one above and it is starting to scare me about driving. I find myself revving the engine when I coast in neutral to slow down to prevent this from happening. This happens either with the clutch depressed and gear engaged and slowing or clutch out and in neutral gear.
The car has never had issues. I am the sole owner. Just coming up on 30,000 miles. I currently have UM tune stage 2, EVOMS intake, APR HPFP, 42DD downpipe with stock cat-back exhaust, HPA short shifter with metal cable bushings, Stoptech Street rotors and pads, VWR springs and RSR clutch, which was installed at about 22,000 miles one year ago. Have serviced it religiously, oil changes every 5,000 miles, did the water pump recall and had no issues thus far.
I moved from high-elevation Utah to New Hampshire last summer. The tune and calibration were all done in Utah prior to the move. These symptoms/issues beginning and getting worse coincided with the cold winter and lots of snow were are having. Could that and the tune having been calibrated at another elevation have anything to do with this?
View 11 Replies
Advertisement
The car is a 91 Chevy Camaro RS , 3.1 V6 and a 5 speed. Mileage is approx 400K + , the odometer has never worked since purchase and showed 239K when I purchased it approx 8 years ago.
The battery croaked due to being low on water and at the same time a stalling problem began so I wonder if the battery going bad may have contributed to the stalling issue.
The battery has been replaced with a new one but the stalling issue has not been resolved by replacing the battery.
At start up the car will idle correctly, occasionally when starting the rpm's will shoot up then slowly slow to correct idle
speed and usually continue to run.
When driving car seems fine but when the clutch is pushed in when coming to a stop at a sign, light, etc the engine rpm's begin to slow from traveling r's down to what would be normal idle speed, this is when it stalls.
If I left foot the brake and keep r's up with my right foot I can prevent the car from stalling. If I (using my foot on the gas) allow the r's to slowly come down to sitting idle speed it usually will not stall.
The cat converter was removed from the car several years back so it's not a clogged exhaust problem.
View 3 Replies
Last night pulling out of a gas station I gave the R some gas and dropped the clutch. The car lurched me into the street but then the RPM just climbed while in gear. Shifted to second, same thing. After a couple of seconds it finally caught and started driving normally.
The whole way home I smelled horrible organic-ness yet didn't feel anymore slipping. To do another test, I have a large hill to climb going into my apartment complex. I went ahead and turned off the traction control and went at it, everything went fine, AWD kicked in and clutch held.
View 9 Replies
Experienced a chatter in the clutch pedal with the a/c on when clutch pedal is pushed in. To me it feels like the throw bearing isn't disengaging the clutch fully, plus my clutch is kind of high once full disengage unless its normal.
View 5 Replies
I started having issues with my clutch pedal "dropping out" from under my foot. Not necessarily during a shift. It still works but will stay down towards the bottom of the travel and after either lifting with my toe or pressing it a few times it kicks back up and usually stays up. Is this my clutch dieing? or something hydraulic related? Hoping I don't have to replace clutch. Searched R32 forum for anything similar and couldn't find anything.
View 8 Replies
So I just recently had to take my 2010 Golf TDI into the shop to replace the mechanics unit. Took them a while to get the unit installed but overall I was happy. The car was driving perfect for about 2-3 months. Then all of a sudden the transmission starting violently surging and dropping the clutch again. I thought the mech unit was going bad again in less than 5K miles. I couldn't get the car in the shop until about 3-4 days after and I did drive the car there because the surging was manageable. It did kick the car into safe mode when the dsg appeared to overheat. It turns out there was a leak from the gasket. They are fixing it now free of charge but it looks like they messed up.
The issue is now I am afraid of any damage that may have been caused to the mech/clutch form the fluid getting low. Should I be worried about this and if so what should I do? I would think the shop should be responsible for any damage done to the car.
View 1 Replies
Got a new clutch, flywheel, and slave done about a month and a half ago at the dealer (got bent over with the price too, but that is beside the point). Ever since, the rpm's have been acting really weird. When the car is in neutral, it will rev by itself from 800-1800. The problem seems to get worse under warm conditions.
I haven't had a chance until today to take it back to the dealer, they scanned it and a couple of codes came up. I will get the exact codes on monday, but they said bring it back then so they can take a closer look at it. What this could be? Throttle body position sensor? Its really pissing me off, and they better fix it. Just want to be well prepared for a fight come monday...
View 2 Replies
I have a MT '12 Golf 2.5L with around 8k miles. I always park with the transmission in neutral. When I first start it up in the morning, the engine revs high, around 1500RPM, so I can clearly hear the engine inside the car. I start it, it revs up and holds, and when I release the clutch I hear what sounds like a rev, but the tach doesn't move.
I believe the GTI doesn't need the clutch depressed for the entire turn over, but the Golf does, so I have to hold it until the engine is running. It may not be a big deal, but I'm just wondering why releasing the clutch in neutral would make a noise. I don't hear it any other time than at start up.
View 1 Replies
The transmission shifts into gear and when the clutch is released it starts to crawl forward. When the throttle pedal is pushed it still revs up the engine normally. But when the transmission is in gear and the throttle is pushed it revs up like it is in neutral. At first I thought this might be a transmission problem but then I figured it might be a linkage somewhere. After looking under the hood and under the car I still couldn't see anything that would cause this problem. I had this car less than a week when this happened and I had to be towed home.
View 4 Replies
So I've been dealing with this for a little while now and it's starting to really irritate me. With my 850, when cold, it drives awesome- perfect engagement, pressure, etc. When hot, I'm noticing that even with the pedal to the floor while in gear, I might get a few 'jerks' until it frees up. Also engaging while hot (in traffic) can sometimes cause rapid 'jerks' which leads to stalling, the pedal engagement is all over the place and you really have to know how to drive the car, just to get it right.
Now I've bled the line about 4 times now in the last three years and it seems to improve slightly (maybe placebo effect), but I'm not looking into it maybe being the grease on the input shaft? I know we greased the throwout bearing and input shaft, but it was a very light coating since I was nervous about getting grease on a $2400 clutch.
View 24 Replies
Started losing pressure on my clutch pedal yesterday. When I would push in the clutch pedal it would not push back up to the reset position. It would only come back up half the way. Now today I have a steady ABS light and ASR light on. Checked for fault codes and found no trouble code. Checked brake fluid resevoir for leaks; still has plenty of fluid. Checked slave cylinder bleeder valve for leaks and looks dry. The only thing I think it could be is the clutch master cylinder. If I drive the car for a few minutes I am able to build pressure back up in the clutch, however the ABS light and ASR light still remain while driving. Turning the car off and back on again shuts off the light for a few minutes until I start driving, but the clutch pressure starts back low again.
View 3 Replies
My clutch has been feeling very strange lately, and has had a mind of its own. I have looked underneath myself, and have even taken it in to two transmission speacialists and they can't figure it out. The master cylinder isn't leaking, and the slave cylinder is fine as well.
Here's what is going on with my clutch...
- I will push in the pedal, and there will be ZERO resistance until about 1 inch from hitting the floor, then all the pressure is there, and I am able to shift. However, sometimes I won't even be able to put it into gear because the clutch won't engage.
- Then I will pump the pedal, and slowly I will gain a little more room on the draw of the clutch, and it will feel fine. All the way to the point where a few days later it will be driving like new.
- Then it will start feeling funky again a few days later and the cycle starts over.
I drive a 2003 GTI 20th AE.
View 6 Replies
I have a 2007 Tacoma 4 cylinder 5 speed. The clutch pedal started sticking about a month ago and has only happened a hand full of times. When the pedal is pushed to the floor it would stick, I thought it was hanging up on the floor mat at first but that was not the case. I went out to move the truck today and the pedal immediately stuck to the floor. Like usual I tapped the pedal kind of on the side to get it to release. the pedal then came back up. But now it wont push back in at all!!! There is only 1/2" of travel on the pedal and stops solid. It's like it is binding up on something. The spring seems to be in place the right way and nothing that I can see obviously wrong.
View 4 Replies
I have a 2002 Honda civic (manual). Lately, when I have pushed in the clutch to start it, the engine makes a bad sound. It sounds similar to the sound an automatic would make when you turn the key while it is already running.
View 3 Replies
1988 Acura Legend, 2.7L 6 cyl., 181,000 miles only do 6,500 miles a year to train station, parked inside, runs great. Last week parked out in hot sun, '90s, for 8 hours. At first, no problem. When did errand and returned to car, pushed clutch pedal and it would not return or allow gear to engage. "Jammed" into 1st, then could not shift, shifted slightly by pulling up on clutch pedal with my foot. Parked overnight, cool, next morning seemed to be fine and crept to mechanic. Mechanic road tested and found no problem and now seems to be working okay. Would parking in sun, high heat cause "clutch cylinder" to "seize" or "freeze"? Is there a "fix"? Also, increasingly hard to get parts for this car.
View 6 Replies
Well here it is I just put a new slave cylinder in my 02' F-150 and once we figured out all the little issues we were having we finally got the truck to fire up!!! Now my problem is that when the truck is running I can't get the truck into gear with the clutch pushed and it doesn't even grind. But when the truck is off it goes through the gears no problem what so ever. When we did the slave cylinder while we were in there we just replaced everything clutch, pressure plate, flywheel, rear seal, and pilot bearing. We figured that since all the shops were quoting me 800 and up for just doing the slave that since were in there we might as well do everything since nothing has ever been replaced yet. My question is why will the truck not let me shift into gears when running but no problem when off. Oh and yes the system was bled after doing the slave actually twice so far.
View 5 Replies
I have a 1997 Ford Ranger XLT 6 cyl. 4 wheel drive. I got this truck from a friend. Only had it for a month or so has about 185K on it but has been running great.
I did notice a couple times that when I pushed the clutch in approaching a light the truck would jump a bit in RPM to about 2600. but go back down in a second or two.
This started to occur more frequently and now it does it almost all the time....when I push clutch in it revs up to about 2600 RPM.
Now I can have my foot on the brake and let the clutch out to put some strain on the engine and knock the RPM down but its still a bot high in the 1k range. Sometimes it actually goes back to normal...
When I started it this morning it was fine....but after two shifts it started and lasted the 12 miles to work. What could be causing this? It does not seem to go above 3000 RPM when it revs.... Other then that the truck runs great.
View 5 Replies
I have an '89 Ranger, Extended Cab, 2x4, 2.3l, Manual transmission with 255,000 on the odometer. I've owned it since 1990 and as far as I can remember it has either never had a clutch or only had one. I realize it's past due.
Everything has been fine up until this morning. 10 minutes after leaving the driveway this morning going a steady 55mph, no incline, it sounded almost as if I hit a deer. The truck jerked real hard, I put it back into 5th, and limped to my destination. Keep in mind for the next 30 or so miles there was absolutely no clutch slippage.
Here's the symptoms: No slippage, won't go into gears (I have to match rev's and shift without clutch, I drive a big rig and do this daily), when I do get it in 1st at a stop sign it wants to lurch with clutch all the way pushed down, I still have a great clutch pedal, and the most interesting thing to me is it sounds like something is being tossed around in my bell housing.
I'm almost 100% certain it's the clutch, however, I just wanted to come on here and report I have no slippage and it sounds like something being tossed around in the bell housing area. Is it possible a piece of the clutch could have "broke" off and that was what that huge jerk at 55 mph was? Approx. how much would a shop charge to put a clutch in on this model? I live in a rural area where prices are not inflated.
View 9 Replies
I have a 2011 Toyota Corolla S 5 speed manual and after 15000 miles I noticed a ticking noise in my engine bay and goes away once I push down on the clutch, but once I get off the clutch the noise comes back. Is this a normal thing or should I be concern? I have 75000 miles on my car now, is it covered through the extended manufacturer warranty coverage of 120000 miles?
View 4 Replies
I've tried everything I can think of to get my cruise control working again to no avail. I have a late 99 with a 6 speed. So far I have checked all the fuses with a multimeter, I've checked continuity from the harness under the dash through the clockspring to the switches, truck does not start without the clutch pushed in so the neutral safety switch works, has the upgraded switch and harness off the master cylinder. the previous owner said the cruise was intermittent about a year after they did the harness and switch recall on it. is there a way to test the harness and switch? I got a 1800 mile round trip coming up in about a week and I am gonna have a sore foot if I cant figure this out.
View 11 Replies
I have a 2005 Camry and it was stalling while driving occasionally. It had gotten worse, so I cleaned the throttle body as was suggested. Now, when I try to start it, the engine revs really high then goes back down and dies. This is without putting any pressure on the accelerator. What to do next?
View 1 Replies
