Golf V R32 :: Turning From P To Reverse Is Rough / Strange Grinding Noise
Feb 17, 2015
So with the temps on the east coast being sub 17 degrees, I noticed my car acting up on cold start and all the way until the car is at operating temp.
1 -- Going from P to Reverse is rough! I allow the car to "break free" sort of speak, before I actually give it gas in reverse and once I give it gas the car bucks violently a couple times and seems to not want to actually reverse... Issue is gone after driving the car and letting it warm up.
2 -- Again right after cold start and until operating temp - Shifting in either D mode or Paddle mode going from 1st to 2nd creates a strange "grinding" noise (I will try to get a video clip of it). The sound is very similar to that of a MK 4 starter beginning to go bad, but not as loud. It only ever happened going into 2nd gear from 1st gear. Once the car was up to operating temp and driven around the sound did not occur. Even after starting the car up again after letting it sit for an hour or two it was okay.
Both things occur on cold start up with the car sitting for roughly 8-10 hours.
View 18 Replies
Advertisement
So most noticeable is when i go into reverse. Initially it makes a loud clunking noise until the car begins moving then it stops ( sounds to come from right under the middle of the car, middle/front). Nothing like this in 1st from a slow start. But Another different noise between first and second when accelerating hard.
As I go to shift from first to second there's another louder clunk in between shifts. It almost sounds as if my seat wasn't bolted down tight and was moving. But definitely coming from under the car again, same spot...I just had a 42DD downpipe installed.
View 2 Replies
Canadian 2012 golf R. Build date 02/2012. 8500km ... Clutch sounds and feels weird since the beginning. But few weeks ago I started to hear a strange noise when parking in reverse. When stopped, clutch pressed, reverse engaged, then slip the clutch to move slowly and I'm hearing a buuuuuu noise for 2 or 3 seconds then stop.
When stopped, no gear, clutch pressed for few seconds then release : clac and like a grinding noise. Press clutch again, after maybe 1 second, the grinding stops. Also when driving normally at low speed, I notice the clutch is very noisy, looks like same grinding noise.
When I let the clutch slip a little bit to start moving from a stop, I feel a vibration. not only in the pedal but also in the car. The passenger can feel that.
Here is two quick videos ...
You will notice the "buuuuuuu" noise and also the grinding.
View 3 Replies
I'm new here and I am having issues with my Lumina. It is a 93 Chevy Lumina Euro 3.1L 6 cylinder and has 192K miles on it. It has had one owner for the past ten years that I know for a fact.
Here's what happened. I was coming back home (2hr trip) The brakes had started making that roaring sound on the way down and had gotten worse when I got ready to make the trip home. Okay so I know the brake pads needed to be changed. No big deal. Well going down the road at 65mph I round a curve and my car starts making this REALLY LOUD grinding clattering noise. It took me forever to get it stopped. I will still in the road and I needed to get it out bc it was right around a curve. So I put it in drive and it wont move. So I put it in reverse and it moves just fine with no problems and no noises made. After backing it out of the road I tried to put it in drive. It moved forward a few inches and stopped like something was binding it up.
So here's the problem.. it will move in reverse with no problems at all and only creeps a couple of inches forward then stops. The harder you press on the gas the more it tries to lurch forward but will not move.. like it's caught on something.
We changed the rear brakes on it. Discovered that the driver side rear rotor and caliper were broke beyond repair so we replaced those too. Still the same.. moves forward a lil bit and stops but will go in reverse just fine. We don't seem to think its the tranny bc it pulls hard and seems to not have any problems pulling.. but its like something is bound up somewhere. That is the best way I know how to explain this situation.
View 8 Replies
I'm getting a weird grinding noise when turning left/right. Doesn't happen with normal turns, just at the sharp extremes. What might cause it?
View 16 Replies
2011 gti. I have about 5300 miles on it and it may be normal or have been doing this since it was new. I just noticed it today. When turning full radius in a parking lot I noticed that it sounded like the brakes were dragging. There is also a slight clicking noise. It does this both on left and right turns.
View 3 Replies
Experiencing a strange grinding noise, around the front right tire area, during acceleration?
View 1 Replies
I just bought a 2009 Prius. Sometimes I accelerate and brake, there is a strange grinding like noise. Seems like its coming from the inside of the car, maybe in dashboard. I'm not familiar with all the sounds the Prius makes, but this doesn't sound like any noise I've heard in a car.
View 6 Replies
I hear this most days I get home after my drive home from work. What this might be? (Video included)....
View 2 Replies
My 2008 Prius with 105k miles recently started having a strange clunking noise when turning at low speed. Dealership diagnosed it as the steering shaft and yoke to replace.
View 7 Replies
I have a 2001 Honda civic. Great car, so far. I need to replace the catalytic converter, however I just passed smog shortly prior to the cc going out so I've been putting it off (bad, I know).
When I drive in the lower gears, 1st and 2nd, the car makes a much louder than normal ggggrrrrrrr sound. Don't know quite how to describe it. Especially when turning corners.
Do I need a new transmission? Does my needing to replace the catalytic converter have anything to do with this?
View 1 Replies
I have a 2013 Passat TDi SE with about 64000 miles on it and 20 rims. I noticed a grinding noise when turning right at low speeds. It was a very slight noise at first, but has gotten louder over the past 1-2 months. The grinding noise sounds like it's coming from the back of the car and only at fairly tight turning radii, with speeds 10 - 20 mph (think going up the levels of a parking garage). What could this be????
Other things to note:
No other noises, vibrations accompany the sound.
I do get the steering rack creek when turning lock-to-lock, but this sound is definitely not that sound.
I mentioned I have 20 wheels thinking that might have something to do with it. They don't rub at all going in a straight line, however.
Sound is only present when turning right.
View 4 Replies
My 1.8 Turbo runs great, but when I am backing uphill (standard 5 speed trans), it makes a grinding noise. Is my tranny bad?! Or what is this? Never have a problem with any of the other gears...
View 5 Replies
1990 Nissan Maxima, i noticed that after changing the struts/springs on my car that when i make a hard right turn while accelerating the car makes a terrible grinding noise. I know this is a classic sign for a CV joint, but could it be anything else? It is definitely not tire rubbing, definitely metal sound. It doesnt seem to be getting worse.
View 1 Replies
I have a 2000 Plymouth Breeze 2.4L.
When I make sharp turns in either direction, I get a grinding noise.
View 5 Replies
Fearing the worse here on my 2011 Prius Four, not IV. When I press the "on" A/C button I hear a grinding noise for about two seconds. Seems to be coming from a low area in engine.
View 15 Replies
I have 2009 corolla with 70000 miles on it. I replaced new brake pads. I have some metal grinding noise when i turn right only. I tried looking online and got few similar problem faced by other people. I am not sure if its exactly same issue. No accident damage. Mostly driven on freeway.
1) noise looks similar
2) I do not get noise when i accelerate
3) for car this old is it expected ?
View 5 Replies
I replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
View 10 Replies
My car has been making this grinding noise for the last 2 months. It happens when I put the car in reverse gear and slowly release the clutch. Rarely happens also in 1st and 2nd and 3rd and is always at the beginning of the transition when I am letting the clutch go. I do not know if it is the transmission, the clutch or any other part. I drive a 2002 Hyundai Elantra 5 speed manual transmission with over 120 k miles
Here is a link to a video I posted so you can hear the noise it makes : [URL] ....
View 19 Replies
Recently had a coworker point out that my truck was making funny noises while it was backing up. It is a 2013 f150. It almost sounds like metal grinding to me. It does not do it while going forward either.
Have been underneath and can't notice anything out of place, although I'm not sure I'd notice if there was.
View 4 Replies
Chasing down a grinding noise. I have done a lot of research but nothing quit matches up with what I am hearing.
I have a 1979 F250 4x4. A few days ago I put the truck in reverse and as I was backing up it was like the drivetrain locked up. After that I put the truck in gear and started on my way. As I got up in speed a pretty loud grinding noise was coming from the tranny. 2nd and 3rd gear aren't bad but when I get up to 40+mph it sounds like crap. If I push in the clutch the grinding is still there. While driving I also put the transfer case in neutral, kept the tranny in gear, pushed in the clutch and the grinding stopped.
I also took the lid off, inspected the forks and thoroughly cleaned the inside but noise still continues.
View 6 Replies
