My r32 mk5 is throwing that code.
I replaced new o2 sensor with oem new one.post cat on driver side.
I have erased dtc and drove 15 miles dtc came back again.
Now i have replaced catalysator on driver side and same thing again.
Last weekend I installed a usp test pipe with a hfc welded in and now I am throwing the code p0160......
What this is and maybe some ways that I can fix it?? I have a hard time believing an o2 sensor is shot since the car only has ~27k miles....
The CEL tripped yesterday and this is the code autozone pulled. WHat does it mean.
View 3 RepliesMy car is a Prius Plus 2012.
One day, I decided to go to a mechanic to clean the EGR pipe. Only the pipe, not the whole EGR. It was an extremely simple operation a mechanical one, not electrical etc. Starting from that day, when I go with the car, from time to time, check engine lights up. For a fraction of a second to up to 2 seconds then it disappear.
The car behave itself without a problem. But still the on-off check engine is really annoying.
So a went to the dealer. Put the car on tester.
Result: no code error !
I went to another garage , put another tester on the car, no error..
How can I actually see what the error is if nothing is stocked in the ECU of the car?
I bought my first VW about 3 months ago (so excited!) It's a 2003 Passat, 5 spd, 1.8t. I've had one thing happen so far (until yesterday). On 4 separate occasions when I'd go to start it, it would crank for a few seconds before it would start. Then once it was running the EPC light would turn on. It seemed to be running normally but I turned it off and restarted it and it started normally and the light extinguished (the first three times). The last time (about a week and a half ago) it kept doing it each time I started it, and upon starting probably the 4th time in a row the MIL came on. I drove it about a mile, turned it off for a few minutes, then turned it back on and it started normally with no malfunction lights on. It's been normal since then. Until yesterday...
Yesterday as I'm accelerating from a stop light (I think I was in 3rd) all of the sudden the engine started running really rough and the MIL came on. I turned around and drove about 2 miles back to where I started at about 20mph. The MIL would be steady while coasting and flash while pressing the accelerator. I got a hold of a diagnostic computer and it came up with 3 codes...
1) P0322 Ignition/Dist Engine Speed Input Circuit No Signal
2) P0302 Cylinder 2 Misfire Detected
3) P0302 Cylinder 2 Misfire Detected PENDING
In the past few weeks I have seen an intermittent "Level Error-Workshop". However every suspension function has worked perfectly, and no height was lost even while sitting at the airport for a week.
How to track down the leak. I can see a tank pressure of about 13 PSI. Is that about right. I did a raise / lower while VCDS was connected and there was a pressure drop to about 11.7 PSI but no level error. What is the correct range of tank pressure settings?
Address 34: Level Control Labels: 3D0-907-553.lbl
Part No: 3D0 907 553 C
Component: LUFTFDR.-CDC- 3C3V0 1122
Coding: 0005521
Shop #: WSC 01065 000 00000
VCID: 2757057592F60B6
1 Fault Found:
01583 - Leak in System Detected
000 - - - Intermittent
I was having an issue with my car not going into boost so I plugged my code reader in and it had 2 codes 1 was p1200 n249 malfunction and the other was diverter valve malfunction so I did the quick easy one and got a new factory diverter valve but it still doesn't go into boost and still reads p1200 n249 what do I need to replace or should I do the n249 bypass it's a bone stock jetta 5 speed.
View 5 RepliesI recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
It all started with a fuel cap loose light (it wasn't) after a day or two the MIL came on and got this code I reset it but I'm sure it'll come back since there's probably a real leak. What can I check myself to find this leak?
View 11 Replies I recently bought my 2010 gti used with 62k miles on it about 3weeks ago. The car had an carbonio intake stage 1 and a stage 1 tune from Apr when I had bought it. On the test drive and for the first two weeks I had it I did not have any problems. A few days ago on a cold start my car threw an MIL and it was flashing. When I got to school I plugged it into the obd2 scanner. Code read P0303: misfire cylinder 3 detected.
My teacher and I went over possibilities of the misfire. Coil pack, plugs , injector, valve float( even tho this should not occur at 1300rpm cold start) we also thought that maybe because the car is direct injection the valve was not closing all the way due to carbon build up on the top of my valves which in this case I'm glad I don't have an interference head. I moved around the coil packs. What is the cause of this? I'm only misfiring at start and when the engine isn't warms up to operating temp.
so my girls car is throwing an evap code (P0442) small leak detected. I bought a new oem gas cap and replaced the purge valve solenoid under the hood. that didn't work, CEL still comes on about 100mi after clearing the code.
I have checked the rubber hoses that were attached to the purge valve solenoid when i replaced it and they are fresh, no dry rot or cracks that i can see. The hose on one side goes to a hard line that runs under the car to the back, the hose on the other side of the solenoid runs under the intake to the throttle body. That hose was fine as well. Connections were tight and i even put better clamps on the hose ends that attach to the solenoid. So I have ruled out that portion of the system (under the hood).
I also removed the rear seat to access the fuel pump. All those connections seem nice and tight, I don't smell any strong gas fumes indicating a leak so i don't think the fuel pump gasket is the problem either. Finally, i checked out the hard lines running under the car front to back and I see no apparent or obvious damage. I assume my next step is to pull off the rear passenger wheel well liner and asses the charcoal canister and the LDP connections, correct??
The last thing I will mention is, Idid notice the 2 fuel lines that attach to the fuel regulator are in pretty rough shape, however not leaking any fuel. Are both of these lines actual liquid fuel lines? I am thinking one of them is a vapor return which may be part of the EVAP system. If it's dry-rotted and leaking vapors could that be the culprit??
Secondary air injection system leak detected-Bank 1 & 2... 2003 miles on my car and the CEL pops on this morning. VCV bodies are being replaced tomorrow. The tech didn't fully understand what parameters to test for or what conditions would be present to set this code, I can't say that I do either... the flapper could possibly play a role in this..?
View 5 RepliesI got 2001 vw jetta 2.0.. I keep getting check engine light,,when i scan it keep saying P0411 Secondary Air Injection System Incorrect Flow Detected. i replaced new smog air pump, and new egr valve and today i was driving car and i got check engine light, its still same code.
View 4 RepliesSo of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
My van stumbling upon acceleration. Well now I am getting the following codes and the van barely has enough power to move. The codes are: P1860 Enhanced: Tcc Pulse width modulation sol ckt electrical, P0758 Shift sol B ckt electrical, PO755 Shift Sol B malfunction, PO740 TCC ckt malfunction
View 7 RepliesI bought a gorgeous red 4.0L V-6 Mustang very cheap last week because it needed a clutch. I would not even pull the car. Little did I know that the clutch kit, including the slave cylinder and flywheel, was over $600. (But that's another story.)
The car runs now, but will not go over 3800 RPM in any gear. It had NINE codes, which they cleared. I was told that they primarily pointed to the MAF sensor. I cleaned it with the recommended aerosol. I have driven it 20 miles, and the MIL has not returned, but the little wrench symbol has. The Manual says to take it to the dealer (of course). The car seems to run fairly well, with the exception of the low rev limit. It is a "fly by wire" set up, with electronic throttle.
The cleared codes were P0102, P0113, P0135, P0141, P0155, P0161, P0403, P0443, and P0446. They actually repeated on Autozone's scanner. (My six year old Actron won't link to this car for some reason.
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
I am getting a CEL and the error code is p2187 engine too lean at idle. I have been reading around to try and find the issue, some seem to say PCV could be the issue. I have also read a test would be try and remove the oil cap while car is idling. I did this test and the oil cap was difficult to remove and the idle got really rough once removed.
View 2 RepliesMy r is throwing a p0601 sum error. I clear, it comes right back. I know the previous owner has it chipped at a garage that wasn't linked to any brand. I was planning on putting an apr/giac tune over it but now I can't (no money). I know this might mean I need a new ecu. Right now I plan on going to vw on monday and having them reflash the ecu bringing it back to stock...if it returns then i guess i need a new ecu... This sound right?
View 5 RepliesI've got a golf tdi with a tune and straight pipe exhaust, and after I hit about 115mph I get a system error code. When I shut of my car, it dissapears and when I try to find it with a code reader, its no where to be found. What's the cause?
View 6 Replies