Lately my car takes 2-3 cranks before it starts and I'm thinking it could be my fuel pump. There were a few times recently it took like 8 cranks to start. How to test fuel flow to see if it has issue? Also, could a old battery cause this issue?
View 18 RepliesThe car cranks absolutely 100%, in no way is this the battery, it just will not start. Then I noticed the fuel pump wasn't shutting off, I only had a quarter tank in the car, I figured as hot as it was today I was getting some vapor lock with the fuel. Went and got some gas, still wouldn't start, then the dash started yelling at me telling me I have no oil pressure, shut off the car.........car you are not running calm down. So then there's that along with the car not starting. I took the fuel hose off to make sure I was getting fuel, I was, so I took the key back out, but the car would not give up, the fuel pump kept going and the dash was blinking violently. When I put the hose back on and got compression it finally stopped, that can't be how the cars work can it? The fuel pump doesn't shut off if there's no compression? Checked all fuses and the fuel pump relay, every was fine, the fuel pump even still ran with the relay out. What could be going on, I can't seem to find one damn thing even related to the fuel pump not shutting off.
View 24 RepliesWas driving normal and my 2004 r32 died. It felt just like it ran out of gas. Fuel pump was not making any noise. I replaced fuel pump relay and now i can here the fuel pump making noise. Pulled the fuel pump line off and fuel is coming out the line. So now i checked for spark and have none. I have 12 volts at the coils. I ohmed out the crank sensor and have .777 k ohms. I also checked codes with generic snap-on scanner and found no codes.
View 2 Replies2005 1.8t gti wont start. The other day I was driving on the highway when a thin plastic type wrapping got caught in my serpentine belt. The car immediately died and I hit the gas and nothing and with no power steering i pulled over to the side.
Timing belt was done with water pump and tensioners
Spark plugs and coils are brand new
What fuel line to disconnect to test if the fuel pump works? Like I said in the title I cant hear the fuel pump priming. The engine was running 100% before this 2 techs saw it and the vw dealer i workrd at looked it over.
01 7.3. Cranks, won't start. Tank was at 1/4 but is full now. The lift pump runs, I can feel and hear that the motor is spinning when I cycle the key. I removed the fuel filter and cycled the key and get no fuel into the bowl. It looks like the lines are stainless from the pump to the tank so I doubt it is sucking air. I pressurized the tank with a shop vac and I get fuel coming into the filter housing. Am I missing something obvious? I have never seen an electric pump that would run and not pump fuel. I removed the suction line at the pump and don't feel any suction there.
View 14 RepliesAccent that will crank but won't start. I found out that the fuel pump was not spinning, so I purchased a replacement. Before installing it, I connected all of the wires and the new pump wouldn't spin either. I then hooked the pump directly to the battery and it spins with no problems. After that I realized that the power wire for the pump must be shorting somewhere. So I hooked up the old pump and ran a new power wire from the relay box to the pump. The pump now runs, but the car still won't start. I definitely have fuel to the rail now. I unhooked the fuel line at the fuel rail and it sprays as soon as I turn the key to "On". Now all I need to know is if I'm forgetting something (bleeding the fuel rail?, etc.). Are there any other parts I'm forgetting?
View 24 RepliesI don't drive the truck much anymore but over time my MPG has gone to total crap...about 10mpg around town...and that's baby-ing it.
Now it suddenly takes many cranks to finally start on a first start. (cold or warm days)....
Car cranks over. Its getting fuel (you can smell it). Sometimes it tries to start but then putters out. Cam Position sensor? I haven't had a chance to pull codes. Ill hook it up to a vag com in the morning when i get back to work (car is parked there for now).
View 24 RepliesSo heres the deal 1989 civic dx hatchback 106k on the odometer automatic 1.5l d15b2 engine . It's been having delayed starts taking 3 to 6 cranks before firing up then running fine, suddenly it dawned on me maybe it was the distributor , so I swapped it with a spare I had because sure enough the old one had red death red dust in the cap. Cleaned the contacts set the timing reassembled, some wires broke on the back of the wiring harness to the distro. Rewired them, the car kept getting worse I jumped it and took it to my friend a vw mechanic it drove 49 miles there fine after the jump, new plugs new wires new fuel filter we did the wire job set the timing checked the timing belt got the battery tested and the alternators new and did a oil change also did a coolant flush a few weeks ago.
It started right up drove it back to Chicago , in the morning I was getting off the highway it stopped running no noises I pulled over 8 cranks later it started parked it 3 blocks away, went to test drive it when I stopped at a light it shut off cramming it and hitting the gas pedal got it to start drove it a block down it shut off at a stop sign and I parked it. What it is I'm throwing code 8 which is a top dead sensor which I think is in the distro which I replaced a month ago. Fuel pump sounds like its priming but you have to gas it and crank it to start it which is odd for a automatic , it is girk injected is this tds sensor going to do that by itself? Or could it be a ignition module? ( what I read online) starter? Main relay , fuel pump switch?
2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 12 RepliesSometimes the check engine light comes on and truck will not start,the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad....
View 2 Replies2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 1 RepliesMy issue. 95 short Aerostar, Vulcan engine, A4LD trans. Just got it last week. Bought a new trans and when I went to pull the van into the shop, it wouldn't start. Cranks but won't run. First thing I checked is fuel pressure, got zero. Pulled the kick panel and found the inertia switch, but the harness for the switch is getting 1.8 volts with the key in "ON" and the same with it in "START". IIRC it should be zero in RUN after a second or two (if the engine isn't actually running, that is), and 14 in START.
Checked all fuses in the panel by the steering column, they're good, and switched around the 3 relays by the battery. No good and I don't hear the FP relay when I turn the key. For now I'll run wires directly from the battery to the pump, just til I get the trans done, but it needs to be fixed anyway because I plan to make this van a DD. Here are my questions:
-Is there a second fuse panel I didn't find?
-Could this be a computer issue? If it is, would the computer fuse be blown?
My Santa Fe quit running one day as I was driving. The fuel pump hums when I turn the key to on. The spark plugs look ok. One coil is not getting a spark. We replaced that coil and it still isn't sparking. The timing belt appears to be fine. I bought an OBD II reader, and it gave me the code for the camshaft position sensor. We replaced that today, but there is still no spark. I cleared the code and tried to start the car. There are no codes present so I am assuming I fixed the camshaft sensor issue. Next up on the list is to replace the wiring leading up to the ignition coil. I gave it a quick look over. It appears to be ok, but I might replace it anyway. The outer housing is cracked a little, but the car is 13 years old so I expect that. Before it died there was an awful sound coming from the engine. It sounded like a piston was rubbing/scraping. I am throwing that out there just in case it is related to my electrical issues. I have noticed other weird electrical issues as well. The middle brake light usually works, but sometimes it doesn't work and sometimes only part of it works.
View 4 Replies1999 Jetta 2.0L manual trans
One day out of the blue the car would not crank or start. Checked and found that fuse #14 was blown and would blow the instant another fuse was inserted. Checked all the typical locations for wiring issues usually associated with the comfort module because it had all the symptoms of a faulty module (the power windows did not work and the fuel pump didn't pressurize the system when the driver door was opened, the alarm didn't set, automatic door locks also inoperable).
I checked the dome light, trunk hinges, rubber boot between doors and body and found nothing. Put a jumper wire into the neutral start relay and was able to crank the car. I then replaced clutch safety switch, neutral start relay and installed new (junkyard) comfort module and the car cranked up, started and everything was working normally again...for about 3 weeks. Then it did the exact same thing again. Fuse #14 was blown again and would blow the new fuse as soon as it touched the terminals in the fuse box.
I reinstalled the jumper wire in the start relay in order to be able to drive the car for the last week, and then last night out of the blue the car would crank, but not start. I turned the engine over several times and could hear the fuel pump pumping and even smell fuel, but no start. 3-5 minutes later after random tries to start, the car stumbles to life as if it wasn't getting fuel, and then drove 10 miles home with no issues. I returned the 'faulty' comfort module Monday and got another one but haven't installed it yet because I fear the same thing happening with this one as the other one.
Last night after I got the car home, I plugged in the comfort module and everything worked like it was supposed to. Can a faulty fuel pump damage the control module? I'm trying to get to the bottom of this and fix the problem and not the symptoms so I'm looking into anything that could potentially cause the problem.
Its a 2005 awp 1.8t gti with 180K stage 2 apr. When i tune the key to the accessories on position I used to hear the fuel pump priming but now I don't and the car wont start.
View 5 RepliesSometimes my Bravada won't start. It cranks good (new battery) and I can hear the fuel pump , but it doesn't fire up. I just got it back from the repair shop.?
View 4 RepliesMy eXcursion is showing the typical signs of a failing fuel pump. It cranks and fires on a few cylinders, then quits. I released the schrader valve on the fuel rail but very little pressure is released. From these indications, and after checking for a blown fuse, it appears the fuel pump is going. I say going because it did start after this happened, but would you trust it?
I ordered a new fuel pump, it's due in tomorrow. I remember seeing instructions on how to drop the tank but can't locate them with the search function. I'm also concerned with how to remove the pump from inside the tank. I know you have to spin off the big plastic ring, how do you get the pump off the bottom of the tank?
2002 E-250 with the 4.6 V-6. Pulled the 30 amp fuse, replaced the fuel filter, replaced the fuse, now the truck wont start. Checked the fuse and the kill switch under the passenger kick cover, all ok. Cranks and cranks but wont fire. No problem prior to changing the filter. Even swithed out the relay with another, no luck.
View 4 RepliesI'm having an issue ( happened about 6 times now) where engine is taking 5 to 10 attempts to start after, and only after, I put fuel in! Engine turns over but 3 seconds later dies. I have had the starter, battery and alternator checked and they are all fine. , it only happens after I fuel and I have tried a bunch of different gas stations so I know its not bad fuel. In between fuel ups engine runs fine and never a starting issue.
View 1 RepliesI took my fuel pressure regulator off hoping it would get to my green top coolant temp sensor. It doesn't Now when I put it back on its leaking? I didn't depressurize the fuel line first. Can this be the cause? If so do I just open the gas cap, pull the fuse for the fuel pump, and then re-insert the fuel pressure regulator? or do I need to get new O-rings for the regulator?
View 10 Replies