Golf V R32 :: High Revving When Hitting The Pedal Hard?
Apr 27, 2012
i did have the mech recall done a while back. lately, on several occasions, when i've hit the pedal to the floor "fast", i would get a high rev to 3-4k with the car not moving any faster and then after the revs come back to 1-2k the car would take off like it should. the perfect example of this would be when i wanted to change lanes or pass someone on the freeway.
the car accelerates normally when i am depressing the pedal incrementally and i haven't seen the same type of thing during any other situation. i've had the car for a year and hadn't really noticed this prior to recent driving.
View 6 Replies
Advertisement
My 2003 subaru outback wagon, manual transmission, starting revving about 1500-2000 rpms higher than normal today. When I put the car in neutral, the car revs high sometimes increasing in rpms. Also when i left off the gas the car doesn't decrease in speed or rpms almost like the gas pedal is sticking. I revved the engine while in neutral a few times to try to see if I could get the rpms to drop but that didn't work. I had two belts changed yesterday (excluding the timing belt) and everything was fine with car until today, after driving 70 miles.
View 2 Replies
When started very high idle after hitting gas pedal sometimes it will lower idle sometimes not,,then holding pressure on gas pedal it has very bad surging ... Any guesses what might be and possible cost fix?? I am no mechanic,will have to take it somewhere...90,000 miles on it..
View 3 Replies
We are planning on taking our 07 Explorer in to the dealer to have them check on a couple of issues. 4.0 with auto and about 45,000 miles on the ody.
1. While taking off after waiting at a stop light or slow speed traffic crawling there is a high revving sound coming from the engine compartment. Sounds like the fan is over revving compared to the engine speed.
2. Recently the truck has a hard time going into reverse. Physically hard to move the gear select lever and there is a hard "thunk" when it does actually shift into reverse.
I just want to be armed with information before heading to the dealer. The truck is still under a warranty plan, I just need to be prepared. Could it have to do with the Transmission Range/Position Sensor?
View 2 Replies
I hit a bump while pressing the brakes for a stop sign (going down hill), and I hear/feel this grinding noise through the pedal right when I hit the bump. I assume it might be the surface after the bump as it happened in the rain and it could be slippery causing the brakes to lock or something. I don't know, I might just be paranoid.
View 2 Replies
Recently, when I start my Golf 2.5 DSG it has been revving a little loud or rough. It usually revs at under 1k at idle, but when starting up it revs at around 1500 until I put it in drive and release the footbrake.
View 10 Replies
I have 46k on stock suspension and lately I have been hearing a clunking sound when hitting bumps. It sounds like it is coming from the strut mounts and the ride has been harsh compared to when the car was newer. There isn't any bounciness and I thing the shocks/struts are fine. I push down on the body and no bounciness when I let up. Could my strut mounts be shot already?
View 6 Replies
I've had this happen a couple of times since winter. The engine will rev high around 2000 rpm then come down back to normal idle speed.
I've recently changed out all ignition coils so I know it's not that.
View 8 Replies
I just brought my gti in for the 20K oil change etc... I have noticed something weird... when I accelerate hard or have been driving for a while, and then shift into neutral or push in the clutch, the engine revs up to almost 2K, then back down to 1K once or twice, then finally settles to 700rpm's. It doesn't do it cold, or when I have the AC running.
I have no CEL's, and the dealer just said they ran a fault check, and it was clear. I do have an APR exhaust and a K&N intake (I think stage1 tune)... I asked about the PCV valve, and they said that would throw a code... They said they could do additional diagnostics out of warranty, since they think it has to be part of my aftermarket stuff.
I don't know if it's related, but if I really jump on it, in 5th gear or so, I can hear the car losing a little rpm's then around 4K just for a second, then it's goes back to normal... This only happened once or twice, so maybe it was just in my head...
View 8 Replies
A couple weeks ago the front brakes were done on the Mazda. Then the wheel bearings needed to be done. I think the shop outsourced what I guess was the packing of the bearings. I paid for the work, and drove away, nearly, but didn't because I had no brakes and there I was pulling out into 5:00 PM traffic. The emergency brake saved me. I walked back into the shop and they discovered the power brake booster had broken. I wonder, because if you drove the Mazda to park it in the shop lot where the customers pick up the vehicles after repairs are made, wouldn't you notice that there is no braking action. The brake pedal was high and hard and there was literally no response when I depressed it.
The shop keeper said, darn I guess I'll have to replace this, meaning pay for it, since it (may have) happened when the bearings were being worked on. My question is, is there any reason why working on bearings might end up breaking the brake booster? Chances are, it was just coincidence, right? or? I don't know. Because the car is old, he had to take several days to find the part. Anyway, he sent me off and told me to drive it carefully. The drive home was absolutely nervewracking and required continual tugging up on the emergency brake stick. I wonder if they despise my car so much now that they are sending me off to drive in it in such an unsafe condition. Anyway, hoping it will be fixed tomorrow. But my question still is ... would working on bearings possibly be cause for breaking the brake booster?
View 9 Replies
I noticed that when I'm stepping on the gas pedal, revving up, when I release the gas pedal I can hear the engine revving up some more instead of slowing down.
When I release the pedal even if the revolution light on the dashboard shows that it is slowly dropping, the engine is still making the noise as if I am stepping on the gas harder for about a second.
Example: I am at a stop, when I start going from 0 to 30 mph, if I release the gas right away that's when I notice this issue.
This doesnt happen when I'm cruising on the same speed and suddenly release the gas.
I wonder if this is an indication the my tranny is having a problem.
I have a 2013 prius C 2...
View 19 Replies
My 2006 V6 Camry XLE feels like there is a delay between hitting the pedal and the car accelerating. I also notice it bucks (changes gears at the wrong time) occasionally when pressing the pedal than backing off of it a little. The hesitation has always been there but lately its been really bothering me because I drove someone else car (Hyundai Sonata 4 cylinder )and felt how smooth it accelerated and how responsive it was at lower speeds. I know this car has drive by wire which probably has something to do with the problem. How to alleviate this issue? I don't think there's anything mechanically wrong.
View 9 Replies
Once hitting gas pedal, it hesitates to accelerate correctly. Also having difficulty turning over after putting key into ignition. RPM gauge will rev up when it shouldn't gas gauge unreliable. Transmission was just rebuilt but didn't fix the hesitation problem.
View 5 Replies
After stepping over gas pedal revving up, when I release the gas pedal I can hear the engine revving up some more instead of slowing down.
When I release the pedal, the engine is still making the noise as if I am stepping on the gas harder for about 3 seconds. when this happened, EV mode will be always not available, and gasoline consumption is increased. Getting lower MPG.
View 12 Replies
2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
View 10 Replies
I had something happened the other day that I have never experienced in any of my Prius' before, I was driving along coming up to a stop lite and the lite changed I tried to make a quick stop and stomped on the brake pedal and pedal got real hard and no stopping! car did not even slow down, luckily no cars where sitting at lite.
View 12 Replies
On my way into work this morning I had one of those everybody needs to stop NOW moments. Hit the brakes hard, really hard with wheels chirping and all, after i got mostly slowed down the pedal gave way and went to the floor. I let up and pushed again and they were fine, but at that point I didn't need to hit them that hard again. The rest of the way in they worked fine braking normally, and before hand as well.
I'm thinking the master cylinder is going bad. Any tips on diagnosing for sure?
View 10 Replies
1614 - Powertrain Control Module (PCM) harness is open or shorted - Faulty Electronic Throttle System (ETS) unit - Faulty Powertrain Control Module (PCM)
1191 - Electronic Throttle System Limp Home Valve On
Car is a 2004 santafe 3.5l automatic. symptoms are phantom revving up to 3-4k in park without me doing anything, sometimes car is hard to start, idle is very erratic/doesn't want to stay running. other times it starts and drives perfectly. from what i can gather this is some sort of malfunction in the electronic throttle system, and from searching people say "inspect ETS system", but i'm not sure what this involves. i unplugged every sensor i can locate in relation to the throttle system, cleaned them with electronic spray cleaner and put some di-electric grease. reset the ecu through battery disconnect, and problem came right back. local shop pulled the codes and said it'll be about 1200 for a new throttle body, and that the dealer has to reset it say what.
is there anything i can do with this sans bringing it to the dealer? i'm not even sure it would make it that far, driving home from the local shop it was in limp mode and i could only drive about 30 mph, and barely made it up hills. probbaly take me three hours to drive to the nearest dealer lol.
i replaced the accelerator pedal sensor about a year ago, and it also threw a code for throttle position sensor about a year ago also.
View 85 Replies
I've been dealing with this for over a year. 97 s-10 (4.3, 4wd, 5spd) always wants to keep revving. When I put it in neutral and coast, the rpms rise. When in gear, it powers itself down the road even when I'm off the gas. The part that really gets me, is that it will keep revving in neutral until the vehicle comes to a COMPLETE STOP. Then, it drops to a nice idle within 2-3 seconds. I don't understand what the momentum of the vehicle has to with the revving of the engine when its in neutral.? I replaced the IAC valve (and set the pintle) and tried to clean up everything I could. It seemed to be better for only a little while. Faulty new part? Is the IAC getting "gummed up" quickly because of something else?
View 3 Replies
I have a 2007 Passat with >120k miles on it. For the last month or so, occasionally when I start the car up, the EPC (I think it stands for Electronic Power Control) light and the Check Engine (the engine sign) light comes on. When I hit the gas, it barely goes past 20 and seems to be revving really high (almost redlining) before it finally accelerates. Needless to say, this is not a good thing; especially when it happens on the freeway.
I called around to a few mechanics but they all want to see the car and run the computer codes on it before they even tell me what's wrong with it; which I am loathe to do just yet because I don't want them to charge me an extra $100 for a diagnostic for a repair I may not even get done with that mechanic. Meanwhile I'm driving around feeling like I should put my feet on the ground like Fred Flintstone to gain speed.
In the research I've done online, I've seen that it may be an issue with the throttle wire or some other wiring issue.
View 1 Replies
I had some problems with my Elantra and I fixed (or tried to) them all this weekend. I needed a new IAC motor, the motor was reving up and down and I tested it, then changed it. I needed a fuel injector and changed that. I needed a lower thermostat housing and changed that.
These changes resulted in the following problems. The vehicle now revs at a high idle all the time at approximately 3000. What are the causes of this?
I know that when I was burping the coolant system (changing out all the hoses and the thermostat housing) I got antifreeze sprayed all over the top of the motor.
Here is the problems that I have now. Didn't have these before.....
The engine idles at or about 3000 rpm. Constant from startup until shutdown. It idles down when you shift it into gear but that is because of the strain on the motor with the brake used.
The transmission is now having problems shifting from 1st to 2nd. I checked the fluid, its good. There is however antifreeze on top of the transmission by some sensors. Do these sensors have anything to do with the shifting?
View 11 Replies
