I recently installed my FK Silverlines and they ride great and look even better. However, they are very clunky. In fact, my whole front end is clunky. Last night I double checked all bolts and retorqued everything with load on the suspension by using a floor jack under the control arm. It sounds like everything is loose and coming apart.
View 24 RepliesI have a 24v gti, but this deals with the front suspension. I replaced my stock suspension with a set of coils and also my drivers side axle with a raxle. Even have new strut mounts, bearings and R32 rear control arm bushings.
When I drive slowly like coming out of the drive way I can hear a continuous clunk happening 1/2 second to 1 sec apart coming from the front suspension, but after I drive a min or 2 it goes away??
Been having this problem for about a month now, and it seems like it keeps getting worse. The shocks feel like they are handling bumps ok....I feel no difference in how the car handles really.....but at lower speeds, going over bumps or pavement variations, I have a thuddy/clunky/floppy (I don't know the best way to describe it) sound coming from the suspension. I think it's from the front. I remember we had something similar to this before but it was in the rear, and I think the culprit ended up being something with the sway bar maybe? This front problem sounds much worse than the rear did though.
2005 Camry XLE 4 cyl
I have a 2012 F350 CCLB with camper package (front coil springs @ 6,000 lbs). I was thinking of installing F550 coils springs, which are rated at 7,000 lbs, to provide greater lift up front.
Before performing this modification, what lift was achieved up front?
My endeavor is not to achieve level, per se, but rather allow for increased tire size, such as 35's and ground clearance.
I will be receiving my 2010 Prius in a day or two. The road condition in Pakistan are not that favorable for the imported cars as they get hit from underneath alot. So I'll need to put 1" spacers on top of the rear suspension. that will require disassembling the shock absorbers. I just need to know how to disassemble the interior to gain access to the suspension nuts inside the car?
View 6 RepliesI am doing an sas on my 93 f150 short bed. my issue is that I've made coil spacers out of 1/2" thick by 3" tall by 4" in dia.... as you can see strength is not an issue here. i bought 6" lift coils for a 93' then decided to just say f it and throw a d44 straight axle under it. the springs on a 78' d44 are the same dia. top to bottom. 93' springs get smaller at the bottom so i made this spacer for two reasons.... 1 to have smaller seat for the bottom of the coil.. and 2 so i could make up the spring length difference between the two springs. The spacers are leaning forward due to the 7 degree c bushings on the radius arms.
View 1 RepliesOk I have an f 150 04 fx4. 120k miles. I was checking a drip on the transmission cooler, and noticed my passenger side coil spring is broken 2nd coil from the bottom. Truck rides well, but obviously this needs to be addressed. Break looks old since it is rusted over, I probably relocated from new England to Florida driving this down 95 with this break, scary.
View 6 Repliesafter I had my springs installed I noticed this air sound when I go over bumbs. is this normal.? if I upgrade my shockts to aftermarket will they make the same sound?
View 9 RepliesB5 Passat, it has the 2.8 and it has been having moments of shuttering so I did a scan and hit 3 engine falts, I did do a clear and rescan so these are new faults.
3 Faults Found:
17801 - Ignition Coil Power Output 1
P1393 - 35-00 - Electrical Malfunction
17802 - Ignition Coil Power Output 2
P1394 - 35-00 - Electrical Malfunction
17803 - Ignition Coil Power Output 3
P1395 - 35-10 - Electrical Malfunction - Intermittent
Right now my guess is the coil pack is going out or loose connection to the coil, this coil is roughly 8 months old so it kinda has me at a loss and hoping its not the coil.
My car misfired multiple times in two days i replaced coil 1 & 3 & it misfired again i took the coil that i replaced and put it back and the car was fine so. i don't think its the coils and i changed spark plug in coil 1, didn't work so I doubt it's coils.....
View 4 RepliesHaving issues with some or all of the coil packs going bad? Because it looks like all 6 coil packs on my R32 went bad...
Brief history, my car stopped turning on about a month ago, it was working just fine when one day when going to lunch it stopped wanting to turn on, I had to crank it about 3 or 4 times and it turned on, I went to lunch then got back but when I left for the day (at work) I once again didn't want to turn on and that's about it. I had to tow it home and a couple of friends and I began trying to figure out why we tested the fuel system and electrical. We could get no little to no spark on all 6 coil packs. Ran vag com and nothing would come up, I tested the Crank position sensor and it tested fine but broke the connector so I replaced it with a new CPS. Still, would not start.
So after a couple of days, we decided to try 6 known good coil packs and it fired right up. So yeah I've never heard of all six coil packs going bad at the same time, so what could cause that ? btw soon after the car started, about the 3rd time turning it off and on the starter decided to stop working, I'm thinking it was because of all the times I tried to start it, it was allotted. : thumb down
I was removing the coil packs on my car in preparation for the new ones coming in. The far right coil pack came out very easily and was about half as long as I expected. The other half of the coil pack was at the bottom of the spark plug well. I reported a misfire yesterday. As the mechanic would say "now there's your problem". removing the bottom half of a coil pack?
View 24 RepliesI've had my 24V off the road for about a year now working on it. I did some wire tucking and what not, nothing major. Now when I go to start it, it won't start and it will make a popping noise from a coil pack and it starts to smoke.
View 6 RepliesI'm driving down the road yesterday, and going through a intersection, get through it i'm in 3rd gear, 20mph, and my car starts to misfire, so i am like crap coil pack, i changed them all with new plugs maybe 1000 miles ago. Well I slow down so i can turn around and head back to my place slowly a mile away. and it never happens again. Now the car had just had the complete exhaust replaced last week, and literally only 9 miles put on the car before this happened. I drove 35 miles to work today, and roughly 50 miles last night after this and it has not happened anymore. Am i doomed for coil pack failure again?
View 6 RepliesI had taken my engine into the shop and had to have to engine replaced, I would have done it myself and would have saved a bunch of money, however I did not have the time. So I had the same exact engine placed into my MK3 from an old Passet, the only issue I'm having now is the sounding of a misfire on one of the plugs..
Only thing is, all plugs and wires are brand new, so I'm thinking the Coil pack is on it's way out the door. The mechanic said it was the original coil pack so that would make sense. It's a 1997 2.8L 6cyl engine.. I'm looking into purchasing a new pack, and on a website that I had been using a lot lately, only had MK4 coil packs.. Can I replace an MK3 pack with an MK4? Would i have to change the plugs and wires again?
I've been doing the 40k service to my R32, and was in the process of changing the spark plugs.
The first three went smooth with no problems, the next three however.... When I pulled the coil packs off, they were covered in rust and corrosion.
The inside of the block leading down to the spark plug (where the coil pack was) also had rust in it. I haven't pulled those three spark plugs out yet. What caused the rusting?
I assume I need to replace these three coil packs, and clean off the existing spark plugs before removing them. Is that a fair assessment?
I haven't had any trouble with misfiring or stalling. The car has been running great.
I'm in the middle of replacing my VC gasket and while I was removing one of the hex bolts that holds it in it started sparking like crazy and turned the tip of the hex wrench glowing red. It didn't do this for the first bolt I took out. I also forgot to disconnect the battery before I started, could that have had anything to do with it?
View 6 RepliesMy R is coming up on 140k miles. The shocks and struts are pretty beat and it rattles badly. I'm really thinking about just replacing the suspension components with oe type stuff or is it really worth it to spend the extra money on a coil over kit? A little lower stance and some adjustability would be nice, but not super important to me. I'd have to get a lower end coil over kit too, so is it really worth it? Or should I just replace the stuff and be done with it?
View 1 RepliesMy Mazda 626 is making a really weird noise somewhere around the back left corner of the car (from the driver's seat). I just noticed it a couple of days ago, ironically enough, shortly after I picked it up from the mechanic for something totally unrelated!
I really only notice it when I'm going under 20mph. It's a dragging/clunky sound like something is loose. My husband checked it out briefly but didn't seem to notice anything different. I know I need to call my mechanic again, but after spending over $1,000 on repairs for both of our cars, my husband and I aren't thrilled about having to take this car back so quickly!
Looking for a wiring diagram or instructions on how to install? I have the MK2 low temp switch with a piece of harness that I need to wire in.
Top is MK2 harness (red/black, red/green, solid red). Bottom is R32 harness (red/white, red/yellow, solid red).
Installed the GFB DV+ noticed a bit of a whistle at idle after installation? You can't hear it inside the car, but if you have it idling and step out, you'll notice it if you have it. It's almost like a vacuum cleaner in the distance, it's not very loud.
View 4 Replies