I'm pretty certain that my 22mm neuspeed sway bar bushings are shot. they squeak like crazy and when I looked at them to grease them up it looked like they had space, oh and they knock like crazy. Any better source or place to check locally? Would Napa carry something like this? and is Poly my only option? would a rubber bushing wear quicker?
View 3 RepliesAs a lot of Camry in this world, my rear sway bar bushings went bad. Tried to replace them, I went slowly with the ratchet on the first bolt as I don't want to go with the impact tool, but that damn bolt decided to break anyway...
I called my local dealer and he said he don't have the replacement in stock and he cannot tell me the size of this bolt.
What is the size? My 07 SE have the bracket with only two bolts.
Front sway bar bushings causing "clicking" noise while turning the steering wheel? Usually happens when I'm moving into or out of a parking spot and while I'm turning my steering wheel. I got the driver side, I believe, lower control arm replaced and after that i started getting a faint clicking noise when I'm turning the steering wheel.
The dealer, after multiple visits, discovered it's the front sway bar bushing causing the noise. They said it's really not worth the cost, since it's isn't a safety issue and the whole sway bar needs to be replace since you can't buy bushings alone. I want to get rid of the noise regardless of safety or not.
2016 2L Escape. My question is this. I've had the vehicle for the past 12 months and each rainy season here in California, I admit its not often we get rain but we have it now and its about time. Anyway while driving in wet conditions I get a squeak from what I think is the right rear sway bushing and it only happens during starting out, stopping and parking lot speed bumps all at low speed. No noise at when driving at speed. I've had it to the dealer 3 x to fix, they grease the bushing and it seems ok for awhile but not he permanent fix I was hoping for.
View 1 RepliesMy Tig has been doing a sharp clunk (single) for awhile when going a bit too fast over speed bumps. I just ignored it, as I'm not flying over bumps regularly and I had just replaced the OEM struts all around. Now when accelerating over 60 kph the car has a side to side shimmy. Also when compressing or unloading the front end suddenly, like with dips on the road, makes it clunk. Checking the various suspension components?
View 6 RepliesI have a 2009 Corolla S. When I drive on the highway and the road dips and then comes back up, I hear a crunching sound as the wheels come back up. It almost sounds like springs. I thought maybe it was the cold weather but it isn't. The sound is in the front end.
At 53,000 miles, it seems early for this kind of problem and I never have had this so early in the life of a car. I do have the Toyota Extended Warranty of 125000 miles and 8 years. Would this be covered under that?
It doesn't really happen over bumps, it's when the car dips down and comes back up on the highway...50 mph or more.
I have a 2002 F350 4x4 CC 7.3 i am wanting to change the sway bar bushings front and rear to poly and I want greasable bushings to avoid the squeaking that you get with these bushings alot of the time. I would like to change the end links to poly too i realize these wont be greaseable. What was the outcome and where did you buy the bushings. What is the size of the front and rear sway bars and the length of the end links??
View 14 RepliesWhat are the specs for the sway bar bushings that go in the retaining bracket for a 2003 ford f250? went to advanced auto last night to get some got mine off my truck and the one they gave me was a little too small for my sway bar and the retaining bracket.
View 2 RepliesI have been having that nice thumping noise that generally accompanies worn out sway bar bushings. I did bushings last spring but a noise came back shortly thereafter. Finally got bothered enough/ found enough time to take a look at it and tracked it down to the sway bar again. My right front axle mount has taken damage before and is now all bent up, not allowing the bushing clamp to hold tight to the bushing. Pictures of the issue are below.
Front view of the entire mount.
Rear view showing the sway bar mount plate.
I am unsure what to do about this mount. As you can see it has been pretty messed up by the PO. What could be done to fix the issue?
So tonight I got the chance to install my H&R Rear sway bar on my car...let me start off by saying I was lucky enough to have a lift, air tools, all the correct tools, etc...now the frustrating part...i opened the box saw the bar and new bushings, figured this should be 100% straight forward 10 min job... the old bar came out in about 3 minutes...then I got the new bushings on the H&R Bar and went to put the factory brackets on...they wouldn't fit even close. Luckily I had a press so I pressed them on. Once I got the bar in the car I got the two top bolts started and could not for the life of me get the bottom two...its like they were 1/4in to low... Was I missing parts from H&R? also the factory caps/brackets seemed to sit off to the side of the new H&R bushings and there was no way to line them up straight, but I finally got everything on there..
View 18 RepliesOn my 99 at the tip of the springs there is what looks used to be plastic wear spacers between the leafs. Mine are worn out and I think it is part of a squeak noise I am chasing.
What that part would be, where I could get them, and do I have to break down the leaf assembly to change them or could I raise the truck by the frame and take the load off the springs enough to get the in?
Rear sway bar make noise when you go over bumps in the road?
View 24 RepliesSo as the title states, rear sway install, no issues (so I thought ) go to test drive the car afterward, and the headlights go through the normal sweep, but, they don't come up and level out, instead, they are pointing 10ft in front of the car.
The test drive was otherwise flawless, the R responds well to swaybars, my Mk6 TDi did as well, I just have the rear H&R bar on the softer/street setting for now, but it makes a notable difference just on its own in the soft setting, I'm pleased.
Back to the issue now at hand, I researched and so far came up with there is a sensor on the drivers side LCA on the rear of the arm, and one on the rear subframe that has a push rod type arm (looks like a servo) attached to it and a bracket on the subframe, Is this correct? The sensor in the rear is intact, plugged in, and I traced the wire back to the wheel well and there is no evidence of a ground, pulled or severed wire. I have no scanning equipment and am leery of going to the dealer and letting them plug into the ECM for anything now that I am tuned, not really for warranty, more for I don't want to risk anything being corrupted or altered.
So after about 3k on my rear sway I checked everything to make sure its tight. All is tight, but i notice it moves very little but its enough to make noise and drive me nuts. hard to explain but if you see the h&r bar it has very small allen head screws inside a ring that keep the bar in place where it bolts to the frame there is only a 1/16 of an inch or so of play and its driving me nuts.
View 14 RepliesI installed my sway on saturday and it went smoothly. The bushings were greased up, bolts were torqued to spec, nothing was rubbing or touching in anyway. Now I am getting a knocked noise coming from the rear passenger side. after driving it for a day or so i check under the car to make sure nothing loosened up and everything was just how it was when i installed it. What the issue could be, but the noise is really annoying.
View 4 RepliesI have a squeak in the rear from my V3 setup that I have been trying to diagnose for many months. I finally measured the spring and perch and have ordered these thrust bearings to try to eliminate the problem. For reference V3 rear springs are 60mm ID on the upper side which contacts the perch. I'll post if it solved the problem.
[URL].................................
Bushings on the rear strut rod and rear carrier assembly where the rod attaches are gone - any source? From what I can tell these are not sourced individually?
View 4 RepliesMy rear control arm bushings are cracking. I was wondering if this is a serious problem and what negative effects it will have if I leave them alone.
View 10 RepliesHave to replace those on 3rd gen vehicle?
View 14 RepliesI have a '92 Aerostar XLT with a rear control arm problem. The bushings have worn out and the rear end floats side to side as much as 1 1/2 inches. Ford says one bushing comes in the arm ( no longer avail ), one is a press in (no longer available), and the other is like a strut bushing and is available but without the other 2 there is no point in replacing the one. How to fix this enormous problem???
View 10 RepliesCan the hellwig sway bar links will work with an oem sway bar? I need new ones and figured why replace with something I know will fail early...
View 3 Replies