I have a set of retros with dual turns. I was wondering how to go about wiring up the turns as my city lights (i have a euro switch). Is there a diagram of the wiring anywhere?
View 3 RepliesI just got a new switch from the dealer, only rear fog control (don't have OEM LED's yet), and I want to turn to the right one position, but the HID's come on, and no city lights. What am I missing?
I have a VCDS... [URL] .....
I cannot stand the way they look, I tried just taking the bulbs out but it throws the warning light. Just curious to see any luck with turning them off in vagcom.
View 3 RepliesI have checked the fuses for the Hazard and the Turn Signals. Both look fine. I tried replacing the turn signal flasher (which was a task in itself). After all of this it is still not working. What else could it be? Simple short?
View 2 RepliesMy brake lights, turn signals, and flasher are not working in my truck. Is it a fuse and what fuse? Could it be a relay?
View 2 RepliesDad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.
View 6 RepliesI just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights don't work.
The front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.
My second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.
I changed the bulbs from the stock to LED then the error light was showing so I decided to switch back the stock lights (I did this while the lights were on).
And now my city lights will not turn on at all! It is a fuse that is causing this problem?
How would I go about wiring the turn signals to be DRL instead of the high beams?
View 8 RepliesMy turn signals will not work with the engine running. With the engine off they will. With the engine running if I move the ignition like I am going to turn it off they work.. Is it the ignition switch or ign cylinder....
View 5 RepliesI must be missing something here. Where is the flasher for the turn signals? It isn't the two relays behind the radio is it?
View 2 RepliesI have a 2006 f150. Both front turn signals do not work. I replaced bulbs still nothing. There back signals do work. They blink really fast.
View 4 RepliesI have a 2001 Econoline and the turn signals work in the morning but when the vehicle warms up they stop working. I have replaced the bulbs and the fuses. What I could try next.
View 4 RepliesI installed LED tail lights a few months ago, now all of a sudden the passenger side does not light for brakes or turn signals. The lights came with resistors that I put in when installing and the adhesive wore out and they were dangling in the truck frame. The wires connecting the resistors to the light were damaged. I taped the exposed wires and secured them a with a heavier tape, but taping did not work. I also tried switching the resistor packs with the driver side to see if it was them that have an open winding, but they are still operable.
I narrowed it down to wiring between the trailer hook up and passenger light assembly in the electrical circuit. I plugged an LED light bar into the trailer connection and the same problem occurred (running lights come on, but no turn signal or brake light). Where could there be a short? Or is this circuit fused somewhere that the running lights come on but a separate fused circuit triggers the higher voltage for LEDs.
So I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 RepliesI had oem LED taillights installed to my car. Dealer coded the car to avoid error lights on dash. The problem is now the city lights under xenons look dimmed. Not as bright as before. I asked him why did it happen and he said that it's normal as it needs to balance the current flow to supply enough power to the LED taillights. I'm not satisfied with this answer though.
View 3 Replies2001 F-350 diesel. Out of nowhere, I start the truck and there's no turn signals. Fuse is blown so I replace it. It immediately blows. Tail lights work. No turn signal, brake lights, or hazards. I haven't hooked up a trailer or done anything abnormal recently. Only the #1 fuse (20Amp) is blown. Pulled bulbs and they work fine. Inspected wiring under and near lights. NOTHING! Any way to localize a short?
View 2 RepliesI found out last night that all 3 of my brake lights are out. However, my tail lights work, and my turn-signals work. So obviously its not a big wiring deal. I was looking for the brake switch but i don't know where its at because i looked underneath. What fuse is the brake lights cause my manual doesn't have it listed. I drive a 04 Elantra GLS.
View 6 RepliesSo I just picked up an R32 and it has a euro switch and euro projector headlights but I've noticed that my parking lights, city lights, and front fogs are all inoperative. Though the turn signals do work. I tried doing a quick search but wasn't really able to come up with anything as to a reason why.
View 7 RepliesI have a 99 gmc jimmy. Head lights and tails lights work. But not the Hazard and or turn signals. I checked fuses. I'm thinking it might be the plug under the ash tray. But I don't want to pull off the dash to find out it isn't that.
View 4 Replies1998 Passat 1.8t B5 sedan. OEM fog lights up front. No rear fog lights.
I recently upgraded to a "Euro" light switch to get more flexibility with my lights. Put tape on the TFL pin to disable DRLs in OFF Mode. Put tape on the 56d pin to disable DRLs in CITY LIGHTS (Parking Lights) mode. Completely successful -- no DRLs, just as taping the TFL pin on the original light switch accomplished long ago.
BEFORE I did any taping this time, I installed the Euro switch AS IS and tested all of its modes and physical positions:
(1) OFF: No fog light position available (switch knob will not pull out). As expected and okay.
(2) FULL ON Fog lights come on (but who the hell can see them?!?) when switch knob is pulled out one stop into the fog light position -- and the little front fog symbol on the switch lights up. Again, expected and just fine.
(3) CITY LIGHTS (Parking Lights): The fog lights position is physically available by pulling the switch knob out one stop... BUT THE PARKING LIGHTS DO NOT COME ON (regardless of ignition switch position, emergency hand brake position, etc., etc.) And the little fog light symbol on the switch does not light up. (Not surprisingly, pulling the knob further out to the REAR fog light position does nothing either.)
THIS IS NOT GOOD - since with a Euroswitch one ought to be able to manually select and de-select the fog lights while in CITY LIGHTS (Parking Lights) mode!
How to make my FRONT FOG LIGHTS available in Euroswitch CITY LIGHTS (Parking Lights) mode...?