I need to put a check valve into the vacuum line that runs to the gas tank. I know that this line is somewhere in the rear passenger side of the engine compartment, but there's so many lines there that I find myself confused when I look at it.
View 1 RepliesQuestion, I have a 2003 VW Golf GLS 2.0L AHV (5 speed). The brake vacuum line is cracked after the check valve on the intake side. I looked up the part number on the hose (at work and don't have it on me at the moment), did some research and noticed some revisions to that part number. Eventually settled on [URL] ..... (I ordered a new one since I needed to order a few things). Needless to say, I am beginning to think I ordered wrong.
I noticed that the check valve on the new hose has a 3rd piece that a smaller hose looks to clamp on? The check valve that is in my car doesn't have that. Did I order the wrong part? or did I need to be a cap?
I have a '98 Ford F-150 XLT, 2WD, Short bed, Ext. cab, 4.6L, automatic trans. with 65,000 orig. miles. I bought this truck new. When I have the A/C or heater or just outside air coming in through the dash or floor vents, the air will switch to coming out of the defrosters when I accelerate and then the air will return to it's normal position when I let up on the gas. Is this caused by a bad vacuum check valve and if so where is it located and what does it look like??
View 11 RepliesI replaced my EGR valve vacuum check valve, but now started getting sputtering/rough idle. I'm pretty sure the direction of the vacuum check valve is correct, but I tried both ways to be sure and still got the sputtering at idle.
The old vacuum check valve didn't give me the sputter. I only replaced it because it was melted and I'm not sure it was working. I included a photo of it. It's orange and black.
I have an 2002 Volkswagen GTi 337 edition with the 1.8t engine in it. My check engine light came on so I went to my local autozone to check the code and that's what code it threw on the ODBII sensor. It says my problem could be a "failed clutch vacuum vent valve switch". It also revs about 100-200 rpms extra in between shifts and I'm not a mechanic but know a little about cars. I just don't know if I should replace the OEM clutch safety switch or what I should do about this.
View 19 RepliesSo the day before my 20,000 mile service was scheduled my check engine light came on. I took the car into the dealer and told them the light was on. When I got the call that the car was done they said that the EGR valve was bad and they ordered me another one. They said that they cleared the code and that the part would be in this week. Since they cleared the light it has not come back on. My question is did I lose my Revo stage one tune in my TDI? The dealer never said anything so I didn't want to ask if they had reset my ECU.
View 2 RepliesSwapping a 2004 2.4 motor and trans into my 03 that has a locked up motor. Pulled the motor out of the 2004 yesterday and started tearing into my 2003 today and noticed that the 2004 motor and harness doesn't have the provision for the vacuum control valve mounted in the air cleaner lid like the 2003 has. Since I'll be using the harness and ECM from the 2004 into the 2003, wondering if I can just either use the lid from the 2003 and keep the VCV(hook lines back up) but not have electrical connection going to it. It will basically be pulling the vapors 100% of the time since there is no power going to it and it's a naturally open valve.
Using the harness from the 2004 that I pulled with the engine, there is no way of hooking up to the VCV since the 2004 didn't have one(hence no electrical connector).
This is my other question. I have an APR program and turbo-back billy boat exhaust. I installed a boost gauge that gets the reading off of the intake manifold (fuel regulator.)
So if I'm just tooling along, short-shifting and only using 1/10 throttle, and my boost gauge never reads above -5, let alone 0 or positive, why does my valve release pressure?
Why would there be pressure to release if there is a vacuum, according to the gauge? I wouldn't think that a recirculating or blow-off valve would work in reverse.
My wife has a stock 03 Passat 1.8t.
1. The car seems to shift too soon from 2nd to 3rd and i can hear the turbo drop pressure. It sounds like a quiet blow off 3 or 4 times when it shifts from 2nd to 3rd.
2. There is a vacuum control valve that sits on top of the air cleaner box and it ticks a lot. it has a electric plug going to it.
3. The car has a rough idle while in drive and sometimes shifts hard. I changed plugs, trans flush and filter change.
I would take the car to a VW dealer but the closest one is about a hour away and my wife needs the car.
I have an '04 Explorer Limited and lately only blows cold air. I've read about the blend door motors but it's been too cold in MI to want to do much--so the truck sits.
When I was troubleshooting the problem I found that I'm not getting any vacuum signal to the heater valve in the coolant line. Before I contemplate removing the console & doing surgery on my dash I'd like to know for sure what position the valve should be in when heat is called for.
All the other vacuum actuators seem to be working normally and there's no disconnected hoses under the dash; and no leaks. Coolant reservoir is full.
What this part it is? It sits over the alternator on the driver side and looks like a couple vacuum hoses plug into it. Mine is making a very loud buzzing noise.
View 8 Replies02 F150, 5.4 gas motor, about 338k miles. Bought this truck well used so I would have a truck when I needed one. Someone has removed the heater control valve. I've got a new one, but there is a port on the top for a vacuum line, but where this line plugs into.
View 1 RepliesCan't find the PCV air inlet hose to the crankcase on a 5.4 3 valve V8 2006 F150. Most PCVs let air in on one bank and out the other bank on a V engine, but this engine has hoses going from BOTH banks valve covers to the intake manifold. The crankcase is under vacuum(8 inches vacuum at dipstick tube, 6 inches at each valve cover). There should be air flow in the crankcase not vacuum. No air is getting in which results in a vacuum in the crankcase.
Once the vacuum builds up enough after a few seconds when the engine is started the engine begins to whistle where air is being sucked in(can't figure out where) at a seal or gasket. If air could get in as it should there wouldn't be a vacuum in the crankcase and the engine wouldn't whistle. Where is the air inlet hose for the PCV system on the 5.4 3 valve V8? It must be clogged or blocked resulting in a vacuum. I can't find the hose and Alldata doesn't show it.
Just bought my volvo several days ago. It was throwing check engine codes so I had it scanned and it came down to a vacuum leak. I found the spot where it was leaking which was a little piece to the left and slightly behind the exhaust manifold, slightly behind and beneath the thermostat housing. It went from a hard plastic vacuum line, to a 1.5 inch rubber vacuum line which plugged into a nipple on the exhaust manifold or something behind the manifold. the rubber section had 3 large holes in it, so i replaced it with more rubber vacuum line. same length and same inner diameter.
What I did notice when I replaced it was that it was too large for the plastic line, slid on way too easy, but i had to fight it onto the nipple. The check engine codes went away for 2 days(I drove about 150 miles over that time) but today, the check engine light came back on, went to auto zone, had them scan it, came back with vacuum leak. So when I got home, I popped the hood, sprayed some carb cleaner by the replacement vacuum job I did, and sure enough the idle changed. What the proper replacement hose is for that area?
[URL] ....
I have a 2000 B5 . It has minor damage front and rear (cosmetic only). Also, the check engine light stays on due to a vacuum leak somewhere between the MAF and the intake manifold. It would need a full paint job at some point after the body work was completed.
View 3 RepliesMy 1999 VW Passat has a check engine P0411, P0422, so I looked for any damaged vacuum lines and found one that was all melted coming out of the blue vacuum reservoir tank in the front left lower bumper area. The line was broken off and I cannot figure out where this line is supposed to go.
View 1 RepliesI have a check engine light on the car and in the past it has been bad gas or a vacuum leak. Dealer says on toyota that is not possible.
View 3 RepliesHow and where to check? This probably has been covered a million times.
View 7 RepliesI got a question, what is after ac hose vacuum left side on a 10 th gen 4.2l engine bay by the firewall, to the right of the blue thing, right of that on that line their is a 2 end diameter rubber vacuum line? What is that called, I need a replacement.
View 7 RepliesI recently had a Jasper rebuilt engine installed in my Ford E150. Since than my check engine light keeps coming on and the computer is saying my cas air mix is "lean". The instaler says i need a new fuel pump.Another mechanic says it is more likely a vacuum problem.I know it's possible that the fuel pump is bad bur since this has just started since the install, I don't believe it can be the fuel pump unless it's just one hell of a coincidence.
View 6 Replies2002 F250 SD 4X4 5.4L. 4.5 inch pro comp lift tire size 305/75/R16. K&N cold air set up. 208,000kms
I know the truck does horrible on gas but lately is been getting worse, maybe I am getting 350km to a tank. Mixed highway city driving. Sounds like I might have a vacuum leak somewhere but I have no engine light. I've had the truck since last year and put about 10,000km. on it done regular oil changes .. brake maintenance no motor work so far.