Last weekend I installed a usp test pipe with a hfc welded in and now I am throwing the code p0160......
What this is and maybe some ways that I can fix it?? I have a hard time believing an o2 sensor is shot since the car only has ~27k miles....
My r32 mk5 is throwing that code.
I replaced new o2 sensor with oem new one.post cat on driver side.
I have erased dtc and drove 15 miles dtc came back again.
Now i have replaced catalysator on driver side and same thing again.
I have an 04 GLI and keeps throwing a code for the 02 sensor, and after putting the car on the lift, and disconnecting the 02 sensor harness, a fine oil leaks out at the end of the connector and smells and looks like power steering fluid.
View 9 RepliesSo my 02 Camry V6 has the check engine light on. I had them scan at AutoZone. the codes that came up were P1130 and P1135. After reading some threads here, seems like it's the A/F sensor?
Just to confirm, there are two A/F sensors in the V6 model? I can see the front one easily but not the rear one. Need to identify which sensor needs replacement?
I've got a 2006 F350 5.4L.
The ABS light came on and it was throwing a 'rear speed sensor' code. I searched around and it seemed to be a common issue that the sensor goes bad and needs to be replaced.
I bought a sensor and replaced it, but in doing so, I saw that while the sensor was indeed bad (cracked) the wire right at the connector was corroded.
I replaced the sensor but the ABS light is still on the dash. Is it possible that they code simply needs to be cleared? I was able to read it with my OBD2 dongle and Dash Command App, but maybe I'm not able to clear it?
Or is it more likely that the corroded wire on the connector is the issue? (it wasn't fully corroded and I cleaned it up and sealed it.). It didn't look like I could pull the wires out of the connector, so I assume I'll need a new connector. What is the part number?
So my girlfriends's 2001 2.0 Golf (engine code AVH, 153k miles) began throwing codes for misfire on cylinder 4 and for the o2 sensor (post-cat) recently. I went ahead and replaced the spark plugs, wireset, and the coil pack. They were way overdue. The CEL went away for like 30 miles, and then came back. Now it's reading misfire on cylinder 3 and the same thing for the o2 sensor. What else it could be? Search is coming up blank, most people replaced the coil pack and the CEL went away.
View 2 RepliesI am stage 1 tuned and just have simple bolt ons. About a year and a half ago i had my CEL come on and it was P2400. I was still under warranty and took it into the dealer. They ran through the whole eval system along with replace my evap pump and the CEL was still on. Well then they replaced the ECU and all was fixed. that following fall i took it to APR to get ref lashed and all was well. Until 2 weeks ago. The CEL is back on throwing the same code. I believe its the ECU again and I'm waiting to get into APR to have them fix whatever it is. They believe its evap but I'm not convinced.
View 2 RepliesI own a 2003 VW Jetta GLS 2.0L 4 Cylinder and my CEL recently came on throwing the PO420 code (Catalyst System Efficiency Below Threshold (Bank 1)). So I replaced both the upstream and downstream O2 sensors. Well just one day after replacing the sensors the CEL came back on with the same code. I was wondering weather or not I should replace the whole catalytic converter or if there was anything else I should try. The car runs fine, exactly how it did when I bought it.
View 22 RepliesI have a 03 GLI 24v VR6 thats throwing a P0113 code, which is for the intake air temperature sensor. The sensor is part of the MAF sensor, ive tried 2 brand new BOSCH MAF sensors yet the same check engine continues to reoccur. Is there anything else that oculd be triggering it to come on? Is there anyway to bypass/disable it through vagcom?
View 8 RepliesA couple months ago I was hearing a hissing noise under the hood throwing the same code replaced the Valve cover, after there was no issues. Yesterday saw I had CEL and I was throwing P0174 code and there is a similar vacuum leak sound coming from under the hood but the Breather in the valve cover is not sucking in air. The Oil cap comes off but the engine starts to bog, what it could be now?
View 2 RepliesI'm working on a 2003 Jetta GLI 1.8t (MT and 140,000m if it matters). The CEL has been on for a couple of weeks because of an exhaust leak throwing a catalyst efficiency code. After I make this post I'm going to run down to the advance auto I used to work at & see if I can borrow the scanner to see if there's anything new, but as of right now I don't know. I'll update the thread if I find anything.
The car started yesterday AM perfectly fine. Started again when I left work around noon. No problems with the start, idle, acceleration.. it's all good.
3 hours later I tried to start it to go pick up my kid from school but it just cranked without firing and would not start. I took care of business with the kiddo and then started trying to pin down the problem.
1. Opened the door & listened for the fuel pump to prime.. No sound.
2. Noticed the dome light is on.
3. Checked ALL of the fuses on the side of the dash.. All are fine. Turned key to listen for secondary prime.. no sound.
4. Bought Fuel pump relay & replaced.. no change.
5. Cursed.. a lot
6. Bought fuel pump.. replaced.. no change.
7. Cursed a lot more.. and cried a little too.
8. Noticed the fuel pump was now priming with the key being turned, but still not when I open the door.. Dash indicates the known CEL, but now I notice that the EPC light is on too (this could be from all the fruitless cranking drawing down the battery charge)
9. Figured I'd throw in a new crank angle sensor cuz of the EPC.. no change.
10. Shot starting fluid down the intake.. didn't hit a lick.
I feel like I'm at a dead end.. It's acting like a bad ignition control module, but there's no such thing on a vw 1.8t.
My CEL came on and is throwing code P0430. Is it just an o2 sensor? if so which one primary or secondary?
View 2 RepliesWife has a 2013 V and I bought a 2007 with 200000k on the clock. Got a good deal on the car and knew I would have some issues so here is what I am battling. CEL came on and throwing code P1116. We all know the generic code saying engine coolant temp sensor, cooling sensor clogged, etc. this is the only code on the reader. I checked the coolant level and everything is within standards. No leaks appear from the lines. I believe the carfax shows a fender bender so maybe the CHS tank sensor didn't get replaced? So, I guess what I am asking is:
Should I buy a MINi VCI to locate the problem (I plan on getting one eventually just wanted to save money isolating the problem now)? ECU problem? I have read previous post with bad ECUs throwing P1116 but these post were 2+ years. Sometimes it sounds like there might be gurgling from the dash...I say sometimes lightly because it is very faint but have also read older post stating air could throw the p1116 code so maybe a coolant flush?
Also, big question: is the engine coolant temp sensor identical to the CHS tank sensor? The local parts store couldn't find a CHS tank sensor part number just the engine so didn't know if they were the same.
I drive a 1995 3.1L V6 Pontiac Grand Am SE.
My mechanic told me that my EGR valve was throwing a code, so I took it off and cleaned it out and tried to fish out some of the carbon in the air intake tube. I used carb cleaner on the valve and the tube and I sprayed a little bit of air duster into the tube, but it made a funny noise so I stopped after about 1 second of spraying.
When I put it back on, I forgot to snap the wiring harness back onto the top EGR solenoid. I reconnected the negative battery cable and started my car. The gauges red fine. I revved my engine a few times and everything seemed okay. Then I turned off my engine and then turned it back on to listen for any rough idling (that's why I decided to clean the EGR in the first place). Then I turned it off.
When I got out of the car, I realized I forgot to reattach the wiring harness to the EGR. I disconnected the negative battery cable and it sparked a tiny bit. I reconnected the wiring harness to the EGR. Afterwards, I noticed that it had leaked some fluid (I'm guess oil?) into my engine. There was a very small amount of light smoke or steam (not sure which), but it stopped a minute or two later. I've attached a picture for reference.
Is it safe to reconnect my negative battery cable and try restarting my car????
I have a mk4 r32 with 110,000 miles and I'm throwing a p0016 code witch I believe is cam position sensor my timing chains and guides were changed at 90k car runs good and if I erase the code it doesn't come on right away maybe every 200-500 miles:confused could this just be a bad cam sensor there is also no oil leaking from them and they are tight.
View 14 RepliesNeed to diagnose an issue with my 2012 GTI its got 39,000 miles its stage 2 Unitronic tune. So I was driving like an idiot coming home one night and i jumped a set of train tracks. Bent my plastics a little and when I cranked my car the next day my CEL was on. I noticed my intake was much noiser than usual. My buddy checked the code and said i needed a new mass air flow sensor. We replaced it and my CEl came back on within 20 minutes of replacing the sensor.
View 5 RepliesMy 2007 is throwing a CEL code for the radio head unit. The code indicates the CD player is having problems ejecting the CD (there is no CD in the player)
The issue is not affecting the car or engine or MPG. The issue is that I cannot renew my registration without an inspection. I will not pass the inspection with a CEL light on
I have reset the code by disconnecting the battery.
Is there any way to kill the radio or the code.
My 2002 v6 is throwing a cel that reads p0018. What the code description is? the general ob2 scanner mentions a coolant sensor issue but I did some research and i saw where it is a timing sensor for the newer hyundais.
View 4 Replies97 F150 4.6 200xxx on recent rebuild. My truck is throwing P0171 & P0174.
I think I tracked it down to leaky IAC and EGR gasket. I sprayed both with carb cleaner and the RPM's dropped.
My question is, wouldn't the RPM's rise instead of drop? I was under the impression that they would go up if the gaskets were leaking. Or did I use the wrong spray?
1 Fault Found:
00323 - Vehicle Inclination Sensor (G384)
008 - Implausible Signal - Intermittent
Freeze Frame:
Fault Status: 00101000
Fault Priority: 4
Fault Frequency: 3
Reset counter: 143
Mileage: 133853 km
Time Indication: 0
Date: 2000.00.00
Time: 17:27:31
So my check engine light came on in my 04 jetta sw, and when I had the car read, it gave me a code that tracked down to be a bad coolant temp sensor. I bought the replacement part from my local VW dealership, installed it and the check engine light went away. Now about 2 weeks late it came back on, and I am getting a reading of "Coolant temp sensor high voltage". So it goes from needing replaced, then the replacement is running high voltage?
View 3 Replies