Golf IV R32 :: Removing Battery Cable
Mar 9, 2010
Removing the negative battery cable piece that connects the cable to the terminal. Where I can get the screw that tightens the connector around the terminal.
View 4 RepliesRemoving the negative battery cable piece that connects the cable to the terminal. Where I can get the screw that tightens the connector around the terminal.
View 4 RepliesMy car has been having an issue with battery draw. when I don't drive it for 2-3 days the battery is drained enough for me to need my jump pack to start it. I have done a wire tuck on the motor and also have air ride. I hooked a wire up between the battery and the negative cable with a light connected and it lights up with the car off. What I have done so far is to pull each fuse in the door fuse panel individually and the light stayed on the entire time. Next I pulled the power feed to my air ride system out and the light flashes and I can hear what sounds like a relay clicking. If the issue were the air ride I would think disconnecting it would make the light go out.
I need to pull the fuse panel that was on top of the battery and pull those fuses out too. Should I try pulling the relays as well?
I busted the cable end by not removing it properly. My question is what is the proper method of remove the cable from the throttle body? Are the cable ends replaceable? If so who has them as a google search didn't find any? I've tried to find written information but haven't any luck. bl2009
View 1 RepliesWe have a 2009 BMW X5 with an AGM battery that leaked and damaged the negative cable. We don't know what caused this, and we're concerned it might be due to a problem with the battery sensor, voltage regulator, alternator, or electronic system/software. The dealer says there's no way to tell, and that "batteries just leak." However, we pointed out that BMW's online marketing info states that "The acid cannot leak and damage the battery housing." Based on this express warranty, the BMW dealer refunded us the cost of the new battery, cable, and labor. However, since we've read that battery failure is rarely due to the battery itself, but rather a symptom of some other problem, we're concerned.
View 2 RepliesI'm working on a 95 Explorer, and I need to know where the end of the negative battery cable should be bolted to. Right now, it's hooked to a bolt on the back of the starter. That just doesn't sound right......
View 3 RepliesI had to swap in a new battery the other day, and I noticed that the positive terminal connector is broken. I don't really want to pay >$100 for a new cable right now, so any success story about splicing in just a new terminal ring or using one of the generic battery cables?
View 4 RepliesI am installing a wiring harness in my 2007 Camry SE so that I can tow a small flatbed utility trailer I have to carry my kayak on trips. I have the wiring harness all installed except for I now have to route the power cable for the harness from the trunk to the battery in the front of the car. The instructions give no suggestions on how to get the wire to the battery other than to avoid hot parts and suspension parts.
What would be the best and easiest way to get the wire to the front? I'm not well versed in car mechanics or how to take things apart so I would prefer the easiest, most direct way if there is one.
I have already found a grommet in the trunk with a factory wire harness going through it to the bottom of the car so I can route my wire through there, but after that where to go next. The only thing I can think of is there is several brackets holding the 2 fuel lines and the 2 rear brake lines, there is a open spot between the 2 fuel lines so I could use the empty spot in those brackets to hold the wire for most of the way to the front, do fuel lines get hot at all? Do you think it would be safe to route the wire that way?
As for getting into the engine compartment, how to do that without getting in the way of the front suspension while keeping the wire away from the transmission and axles.
If this is too complicated to do myself, my dad has a friend who is a electrician and likes to restore cars that could do it for me but he is almost always busy, thus hard to get a hold of and I like to try and learn some things about my car and do as much as I can on my own.
This is the trailer light wiring harness I have, there is a link for the instruction manual there too
[URL]
Dealer is telling me I need a fuel pressure sensor. I was hoping it would be the PEM which is still under the extended warranty. Is the sensor and the PEM one and the same? By the way, 99% of the time the car runs normally. Assuming the sensor and the PEM are different, could the sensor flat out totally fail at any time?
Dealer is suggesting to replace the negative battery cable!! I remember replacing old cables in my old cars, admittedly many decades ago for a few bucks. Even considering that it is a different world now, can a cable cost that much. Dealer is asking Volvo to consider the sensor as warranty or to participate because I had complained about hesitation more than once starting about five years ago, but they found nothing at that time. My complaint is still in their computer system.
2005 Volvo s40 t5
I replaced a battery on a 1998 jeep grand Cherokee v6. It started and ran fine, but then in my infinite wisdom, I decided to remove the negative battery cable with the engine running to test the alternator. Some smoke started coming from the back of the engine, so I immediately killed it. It wasn't running for more than 5 seconds. When I started it again, it faltered, but the second time it started fine and ran fine, a little more smoke came out but stopped soon. it smelled like burning oil. We drove it around the block with no problems. I know it wasn't the alternator that was smoking because that's not where it was coming from, and I doubt it was the ecu because then it wouldn't run.
View 3 RepliesOver the past year or so I have noticed that when I press the clutch on my 1985 CJ-7 258 that the headlights would get brighter. This happens when driving or just sitting at an idle. This happens only after you press the clutch enough to take up the usual 1/2-1 inch of play in the clutch pedal. When you release the pedal, the lights dim slightly. Another thing that may be related---over the past few months, it has been a bit sluggish to start until, finally, it wouldn't start at all. I looked at the battery and the cable connector on the negative battery pole is partially melted and ran down onto the top of the battery. What the problem might be? I'd hate to get a new battery and just have the same thing happen again.
View 15 RepliesWhen I dropped my 2 frame rail batteries I noticed the clamp on the positive battery cable was broke. How to splice in a new clamp?
Pick and pull is an option. I would rather repair my OEM cable and be done.
While driving home after replacing a dead battery, clearly I didn't tighten the negative cable enough as it popped off while I was driving (I only found this out after I got home though). But even after popping off, the truck kept going, albeit with the battery gauge maxed out and the dashboard/headlights flickering. I turned off what I could (it was night, so I needed headlights!), but it still accelerated well, and there were no noticeable performance issues at all. When I got home, I tightened the cable, started it up again just fine, ran it for a minute, then turned it off and restarted it fine again with no problems.
My concern is: am I looking at serious electrical issues long term, or should I be ok? I'm just trying to make sure that driving without a negative cable for less than a mile doesn't fry certain parts of the car, and end up causing big issues down the road. (Truck is a 2000 dodge dakota slt)
The terminal (+) on the passenger side battery broke, and I see is a 1 piece cable and terminal all together.
Where to get that cable on how create a new one?
When I hook my battery cable up to my battery when negative cable my truck automatically starts turning over without the key in it what could be the problem
View 1 RepliesDid the cam sync replacement on my 96 explorer awd 5.0 l had the tool dropped the sync got it back to where the last one was. Followed the procedure pretty close I did forget to remove the battery cable. So here is the issue I now have 0 fuel to the rail. is there something I might have messed up or left unplugged that would cause this. Did my fuel pump poop out the same time my sync did. I am stumped as even where to start .
View 1 RepliesI just installed a new positive cable set for the dual battery's and the starter checks out good.
View 5 RepliesIf you remove the battery contact (effectively removing power to the car) does the trip odometer reset? Just wondering, as I plan on doing a relay install for my HID setup.
View 2 RepliesI believe my GX470, 03 model, use to unlock the drivers door automatically when I removed the key from the ignition. Now that the battery has been replaced the doors no longer unlock when removing the key. Is there a way to reprogram this?
View 3 RepliesReplacing the factory pos cable from the alt to the bat in the rear yet? if you have what is the path and was it a pain to do? I have not had the chance to get the car on a lift yet to check and don't know even if it needs to be on a lift to do.
View 8 RepliesOk so I was putting a drill bit into the home slot under the shifter boot. I didn't realize it was so deep and the piece dropped all the way down the hole. Is this bad? If so, what can I do to get in there and get it?
View 5 RepliesMy R is an earlier model with the Aux-in in the glovebox. I cannot think of a more inconvenient place to put an aux in cable which is why they change it I am sure. I would like to reroute the existing one or at least add an extender cable from the glove box to one of the unused buttons near the ash tray.
View 2 Replies