Golf IV R32 :: Popping Noise Coming From The Rear End Or Drive Shaft
Jan 12, 2014
so my r32 recently started making a nasty popping noise. the sound seems to either be coming from something in the rear end or drive shaft. not sure why it happened. i went on a 2 hour trip. got there parked it. aired it down (bags) but then when i came back and when to drive it again. it all of a sudden it started making a horrible popping noise. i thought it was the front wheel bearing going out since i knew it need to be replaced but i did that today and its still making the noise.
The noise sound just like a RWD car with a welded diff when it turns. kinda has that locked rear end hop popping noise. i lifted the whole car off the ground and put it in first to let the tires spin in the air but of course theres no weight on them so it doesn't make any noise. i'm really stumped on what it could be. im going to take the driveshaft off and see if it still dose it. then i know its for sure in the rear end. What it could be?
View 4 Replies
Advertisement
So I have a 2015 SE DSG. I'm getting the irritating popping noise, at no particular speed, coming from what sounds to be the middle/rear. It is lowered on H&R coilover, which I have checked over and over again to make sure everything is tight. It started about 500 miles ago, and the Coilovers have been on for about 6000 miles, the car just hit 7000 miles.
View 1 Replies
Car has been making da da da da da noise from the rear for the past week or 2. The noise is consistent with the wheel speed and I can heard it clearly when I am next to barrier or a truck or something the sound will pounce off it. I drop the car off, later they told me the drive shaft is vibrating a lot and it might go.
View 8 Replies
I was getting ready to replace the carrier bearing and noticed the rear pinion seal is leaking. Before attempting the replacement myself, I would like some opinions on the noise in the video below. Is this normal? I am confidant I can replace the carrier bearing and pinion seal, but not sure I have the tools for anything else.
YouTube ...
View 4 Replies
2000 Excursion V10 4x4. I'm getting a popping noise coming from the rear end when I apply the brakes and come to a complete stop and when I release the brakes to take off. It only happens the moment it comes to a complete stop and the moment it takes off. Not when I'm putting it in forward or reverse or accelerating or decelerating. U joints are fine. I was laying under the truck poking around the other day and when I roll it back and forth in park the few inches it'll go, when it comes to the end of it's travel the axle wraps a little and it seems like the transfer case output shaft flange is moving in and out of the transfer case and causing the noise. I'm assuming there is a snap ring holding the output bearing in place. I didn't have time to drop the driveshaft but am planning on it this weekend to see if it still does it when I roll it and to inspect the transfer case. I need to check to make sure the driveshaft splines are not seized up but they seem to have a little free play to them.
View 2 Replies
I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 Replies
I've had my car for 7 years now and it's a love / hate relationship. I probably put more money in maintaining the car than upgrades. So, I have the kw club sports, front and rear neuspeed sway bars, neuspeed front strut bar, and neuspeed control arms. I lost track of how long its been since I've been hearing this popping noise but it occurs almost every time i leave my drive way.
The drive way is not flat. It dips down then comes up to the street. When reversing two tires come of ground, the front left and back right. When that happens, something pops from the rear... Recently it has come to the point when i take a right turn, i hear a pop from the rear.(not all the time). I told my mechanic to check the sway bar bushings but apparently that not the problem. Suspension shocks and springs are fine.
View 1 Replies
I have a 08 r32, hearing a popping noise that sound like its coming from fuel tank. When sitting not running in garage, bout 15 to 20 seconds between pops. Maybe evap system? Just notice after filling up with gas.
View 4 Replies
2001 vr6 manual... I have a popping noise that comes from my suspension. it is in the front, and it has gradually gotten worse over the last month or so. It used to happen when i back out of my drive way only, but now it happens when accelerating from a stop, quickly braking or turning at low speeds. Recently its getting worse and i can start to feel it in my steering wheel sometimes. It doesn't feel like a wheel bearing. Is it bushings? Tie rod? CV Joints? Strut Mount?
View 2 Replies
I need to identify the part numbers for the u joints in the rear drive shaft. The guys at the auto parts store kept telling me I only need two until I showed them that there are clearly three. I just want make sure that I get the correct parts before purchase.
View 5 Replies
Almost every single time I put my .:R in reverse and the car starts moving I hear a popping noise with pauses in between each pop. I think it might be a ball joint and the noise is coming from the front passenger side.
View 18 Replies
I installed KW V3 coilovers back in October. About a week ago I started getting a popping noise in the left rear suspension when going over speed bumps or up my driveway from the street at certain angles. I could not find any evidence of the springs binding, but did notice that there was some separation of rubber around the plastic center of the rubber mount beneath the spring. This likely the problem or loose sub frame bolts?
View 1 Replies
I have a 2004 F350 with a broken drive shaft.
Got the original shaft off and it has the following part number (2C34-4K145-DNA)
but I've since learned that the part number has changed but the only info I could get was 2???. 4R602DQA.
Trying to find the part number so I can find it under 750.00 from the dealer
View 7 Replies
What Spicer Part #s for the rear u-joints would be? I'm not nailing down the right one. I keep finding numerous ones, 1410, 1350, 5-160....
View 8 Replies
I recently bought a 1997 F150 4wd 5sp manual. While changing the fluids, I noticed that the front u joint on the rear drive shaft has a grease fitting. No matter how I rotate that shaft, I cannot access that fitting with my grease gun, even when fitted with a flexible rubber hose.
View 14 Replies
I've got a 2005 Avalanche (basically, a Silverado) which has suddenly developed a possible illness. Whenever I start the truck and begin moving (forward or reverse), I hear one (and only one) loud squeak that seems to be coming from the general area of the torque converter or drive shaft (but who knows exactly). The squeak doesn't happen immediately upon moving but always happens within the first 20-30 feet of movement and then no more. If I put the truck in park, re-engage the automatic transmission and start moving, I cannot recreate the sound.
However, if I turn off the engine altogether, restart the truck and begin moving, it happens again exactly as before. It happens every time the vehicle has been restarted, regardless of whether the engine is hot or cold. Once it's happened, I can drive hundreds of miles and it won't happen again until I turn off the engine and restart it. Further, I've determined recently that if I start the truck on a hill and let it roll while in neutral and without a foot on the brake, the squeak still happens. Therefore, it's not dependent upon the transmission being in gear or the brakes being applied!
View 5 Replies
Today I took the bed off of my 99 ranger. I was sitting on the cab looking down at the rear axle noticed the drive shaft was not entering the rear diff perfectly straight. As I looked further into it, I noticed the distance between the rear spring on the passenger side tire, is noticeably different. To visualize it, the wheel, at the bumper side of the axle, has a shorter distance between it and the leafs than the cab side. Not massive, but a few inches, and it's noticeable now that I can stand over it. I'm beginning to be very annoyed by this truck and it's previous owners, whom I take it , scammed my brother quite well with a $5k tag for a truck with so much not right with it. It's about to become my yard art for awhile.
View 8 Replies
I have a 2014 4WD Super Duty. It has a squeak that is coming from the drive shaft area. I had someone listen to it as I drove slowly next to them. It is a repetitive: squeak squeak squeak squeak squeak. Not loud. The frequency increases as speed increases. I could believe it may be a U joint based on the frequency, but seems hard to believe with a new truck. I heard this sound when I first got it, but the sound was so slight that I thought it was just some sound associated with a newer engine. But now it is becoming a bit louder.
View 4 Replies
I have a 2013 Avalon hybrid that is almost 1 yr old.
I have recently notice a single "pop" noise that seems to be coming from the rear when I turn right with a sharp turn.
I have looked in the trunk and under the vehicle but I cannot find where it is coming from.
View 10 Replies
Had the common problem of ARB rubbing the drive shaft after I lowered an extra 15mm - It didn't rub before I went this extra 15mm. I got adjustable drop links on and they also didn't work. I basically told the garage to sort it out and they put standard drop links back on (not genuine) and also new wishbones because I needed them. Got my car back and the rubbing was even worse. So I raised it back up the 15mm, to where it was before the rubbing started, yet it's still rubbing like crazy. I'm wondering if the new wishbones may be causing this because of new bushings or something and it all being tighter. And also what am I supposed to do? I shouldn't have to buy a whiteline ARB because it wasn't rubbing at this ride height before the wishbones and drop links were changed.
To summarize:
>Lowered car extra 15mm, rubbing started
>Drop links and wishbones changed, rubbing is worse
>Raised back to the point where rubbing started and still rubbing just as badly.
View 4 Replies
Found some cracks in the outside of my driveshaft. 2002 Jetta 1.8T 5-Speed Manual.
Part number: 1J0 407 271 GJ
I'm guessing it's just rust/age. Honestly, I don't even know if this need to be replaced. CV boots are in perfect condition, now cracks or leaks whatsoever.
View 4 Replies