I have a clicking binding noise while at idle, with the clutch out it goes away, when depressed its there. So, is this a bad throw out bearing? Clutches and flywheels?
View 12 Replies I have a '10 manual trans gti. Only 16k miles on it. When starting cold and on an incline/decline at a certain level of clutch play, the transmission emits an odd chirping/whirring noise. Aside from the noise, the transmission is butter.
I brought in into the shop to get inspected and was able to replicate the noise for the technician. His thought was a bad throwout bearing.
Here's where it gets interesting. They quoted me about $600 labor just to confirm the issue. Should it be the throwout bearing, the replacement would be covered under warranty. labor would also be included. However, if they found it to be a wear product it would obviously be on me and stupid expensive.
Some people also thought maybe the clutch plate fingers are slipping? (I don't know that much about cars..)
so lately I've been noticing a slight rattling/knocking noise coming from my car while it is in neutral and the clutch is not pushed it. When I push the clutch in, the noise goes away. I've read that this could be a sign of a bad throw out bearing? Is this right? If it is the throw out bearing, how long can I expect until it completely craps out on me? It seems to only do it on cold starts and sometimes on the uneven ground. I figured I should start saving some money to have this done because I'm not comfortable doing it myself.
Some other questions I had is my car is a 24v VR6 and it has 144k original miles. The timing chains and guides have not been replaced (to my knowledge at least). I know that replacing the throwout bearing requires removal of the transmission and so does doing the lower timing chain. If I get my throw out bearing replaced, should I have them do the chains also since they are already in there? I have no noise coming from my chains at all so there are no signs that they are going bad. Also, should I have my clutch replaced while they are in there? Again, no signs of a bad clutch either.
I have a binding and clicking-ish noise at low speed. Is that a sign of a bad axle?
View 3 RepliesChanging wheel bearing on mk4. makes noise when i turn to the right. what side is bad? i like working on my own car but this might be out of my hands.
View 12 Replies20thae with a UR 7lb flywheel and spec stage 3 clutch. Got rid of the dual mass flywheel and installed a lightweight flywheel and spec clutch now i have a god awful noise that is dead ringer for a throw out bearing noise. talked to the spec guy at waterfest today and he told me that the dual mass acts as a dampener and this just doesn't make any sense in my head. touch the clutch pedal in any gear at any speed and the noise disappears.. uy at spec said it was in the trans and the only option was to change for a thicker gear oil. p.s. i took out the clutch and everything back apart and measured everything is oem thickness and the throw out bearing is in good shape.
View 7 RepliesMy throw out bearing makes a faint chirping noise since I bought the car, but now that the weather has been in teens, it seems to be louder.
I was wondering if it is possible to grease the throw out bearing or something without dropping the transmission.
Title should say Throw-out bearing aka Release bearing.
I have a 2010 5 speed Corolla CE. Having problems with their Throw-out bearings. At around 8000 miles the sqeaking/chirping noise of the bearing was too much so I brought in it to the dealer to fix. They agreed and made the repair.
Now it is only at 10000 miles (22000km) and I can hear it starting again. Just wondering if it is a common problem?
Noise comes and goes as the clutch pedal is released. If you push it in it will go away. It also will happen in all gears but easiest to hear in neutral.
I have a 2008 Elantra with 59,000 miles. When it is warm out (70 F+), the sterering wheel makes a binding noise (squeeking noise - it is hard to describe) when turning. It doesn't do this all the time and it is much more noticeable when it is warm out. The temps are usually mild. This is a recent problem as I haven't noticed it before.
Should I be concerned about this? I want to get it checked before the 60,000 mile mark in case this is a serious issue such as rack and pinion steering problems.
Recently had this problem which started up about a week ago where my car would make this clicking noise whenever I turn left while driving. When I turn to the right there is no noise. Some said that it could be that CV joints need to be replaced. I have a video showing the side that is making the sound, maybe there is something abnormal that I don't see.
[URL]
I replaced all the bearings and put in a rebuilt transmission and still have bearing like noise , seems like the front, directly increasing with speed . Same in neutral, no change with turning or breaking. Getting worse over the past few months.
View 1 RepliesI have a 1998 Ford F150, Manual transmission. It has set for 1 year. Upon driving it for the first time yesterday, it gradually came to a stop. The clutch never smelled hot or appeared to slip. Today I took the inspection cover off and found a rather large nest has been built in the clutch and pressure plate. My question is could this nest cause the throw out bearing from allowing the pressure plate to make proper contact with the clutch. The truck will move in 1st gear and in reverse as long as there is no resistance against the truck.
View 2 RepliesMy 2009 Impreza 2.5i manual transmission makes a clunking binding when I turn. What the issue is it goes away and comes back.
View 1 RepliesJust replaced my OEM clutch and flywheel with SPEC ones and now I have a weird clicking noise during idle from it. Noise goes away when I press in clutch. My technician says that they are known for this noise. Is that true?
View 6 RepliesI have a 98 mustang V6 that has developed a clicking problem. When I use the accelerator it will make a clicking noise. It is only there when I use the accelerator and u if I press down harder the noise is drowned out. I put the car in nuetral and also applied the gas to see if it depended on me moving or not and I still heard the clicking but it was a lot faster. It comes from under the hood area but I don't know where (as specific as I can get).
View 2 RepliesNot my video, but I have the same exact sound coming from my passenger side wheel on my 03 V10 4X4, 130K. Passenger side only, no noise from the other side.
YouTube .....
Before I spring for the Timkin, does this sound like a bad bearing? No play in the wheel, but it's a clicking sound.
it never ends. upon start up of the treg ('04 v6) the a/c goes through a bunch of clicks and clacks. this used to be remedied with the activation of inside air only; now it does not matter and is non-stop. any remedies? i am going to get this fixed before i run over 50k. i am at 49550 right now!
View 5 RepliesI have an '08 Camry LE 4cyl with 80,000 miles.
I was hearing a clicking noise when I turned left. Which I thought was the CV joint, but turned out to be worn struts. Then I began hearing a roaring sound from the front end. I replaced the struts & that fixed the clicking sound but not the roaring. So I thought maybe it just needed an alignment. I took it to dealer After fixing that one they call & say right one was so loud they couldn't hear that left one was roaring too. So they say I need to replace that hub & bearing also.
Are these issues happening very prematurely? What could have caused these problems?
Just started yesterday. Transmission makes a loud clicking noise when put into reverse or drive, once car is driving it shifts fine throughtout the gears. Only happens when car is started up everytime
View 4 RepliesI recently replaced my starter pin my Hyundai Sonata 06 v6 3.3 gls. Installing it was no real issue, but one (there is only one a single wire not the one that you fix on with a bolt and nut) of the electrical connectors from the car to the starter solenoid. The plastic around the conductor pretty much crumbled around my finger, what this connector is called specifically. Now the contacts will not contact properly so i suspect this the source of the rapid clicking issue, since my battery was fully charged. I plan to go to the junkyard too if i can find a replacement. Looking for specifics on the electrical connector?
View 1 RepliesWhen driving my car, my oem shifter makes a clicking noise going into gear. is there a way to get it to stop, other than getting a short throw?
Looking for 2004 gli all weather floor mats? or ones that would fit?
[IMG][URL] ....