Golf IV R32 :: Jerking And Brake Pads Sticking To The Rotors When Turn Left And Right Going Slowly
Dec 20, 2012
Here is the problem. When I reversed the car out of the driveway i noticed it would not reverse freely. It felt as though something was blocking the car (as though the handbrake was still on).. When i turn left and right going slowly it feels like the car is jerking and the brake pads are sticking to the rotors.. Its the same when i reverse but I only feel it when im going slowly and the sound gets louder when turning left or right...
I checked all my break pads and rotors.. Im thinking it could be something with the haldex system... Hope not.. My haldex fluid was changed at 80k and im at 88k now..
View 4 Replies
Advertisement
i have the brake (!) the ABS and the VSC lit up after i got new bearings and new brake pads and rotors, the car was also stalling before the mechanic removed these bearing "dust cover" circles that must have been causing speed sensor interfernce bc the spedometer was stuck on 0....so the car seems to be done stalling after those were removed and all the big lights went off then i hit the brakes a few miles later and those three lights came on...
View 2 Replies
I noticed the front brake pads were touching the rotors when I was painting the brake calipers. I had my e-brake engaged and in park. I'm assuming the e-brake only brakes the rear wheels because the front rotors were still movable. Although the car still rides fine but I'm not sure if this is normal.
View 1 Replies
How to remove the front brakes pads and rotors on my GMC Sierra 2008 - 1500 - crew cab - 4X4.
View 2 Replies
So my car has 36 or so thousands miles and well the rear brake pads and rotors were SHOT! The rear rotor was falling apart and huge chunks were coming off. The issue stands now that I can't spread the rear caliper for anything, the ebrake is off too. I tried to use the C-Clamp trick but it honestly didn't even budge. I also opened up the bleeder and master cylinders cap just to cross that off the list when trying to compress. This is the hardest caliper I've ever had the misfortune of dealing with and I fear that the passenger side is not going to be any better. Aside from spending more money or renting the "tool" is there anything else to check because the C-Clamp trick has work on mine and my father trucks calipers.
View 3 Replies
I'm getting sick of having my rims getting dirty after one hour of driving because of all the brake dust that the OEM pads give off. I keep hearing from shops that ceramic brake pads are not only more quiet but will put out much less brake dust. On the other hand, Lexus is telling me that if I do that, I will forsure damage the rotors but I really feel like they just want me to keep the car stock which is why they're saying that.
Are ceramic brake pads a bad idea with stock rotors?
View 4 Replies
OK, I just got back from having pads and rotors install on my '99 Passat. I was expecting this to clear up the brake and abs light problem but it did not. The brakes still feel mushy and the ABS light still comes on.What should I check? In the brake forum people suggested bleading the brakes, is this the next step? Any quick how to?
View 3 Replies
I am getting an occasional (though increasingly frequent) 'brake pad' noise from one or more of the rear brakes on my NHW11. Initially it would only manifest for half a minute or so per trip (and would disappear after some braking) but it is now more or less constant. It is a light 'rubbing' noise which you would expect from worn brake pads.
View 4 Replies
Ok so we just replaced our front and rear brake pads and had the rotors turned. Our rear brakes are fine but both our front brakes now make a clunking/popping noise when we brake.
View 4 Replies
My brake pads been rattling around whenever i hit the brake slowly. I think its the front one. My car is 160k miles and still using the original brake hardware kit. Will the new one fix this annoying rattle? I just cant see how a new piece of metal will stop the pads to move around.
View 5 Replies
I noticed today (smell burning brakes) that my left rear brake is sticking on my 1999 2WD F250. I hear that this is a common problem? Is it usually a defective Caliper or emergency brake Issue? I had my rear brakes done 50k ago with rotors and rebuilt calipers (first set went 130k).... I don't think it was a total clamp down infrared temperature was 275 degrees on sticking brake and 75 degrees on the ones that were not sticking.
View 9 Replies
I replaced my warped front brake rotors a couple thousand miles ago and all was fine but when I went to swap over to my snow tires, I can see that the outer part of the rotor has been rubbing on the caliper bracket. This is happening on both front rotors. Could my new rotors be too thick or something?
View 4 Replies
I have a 2007 Saturn Relay LWB. Our van will occasionally have a weird vibration occur. Usually when I turn slowly left into our driveway, but on occasion it will happen while driving at any speeds and any direction but mostly if I turned slightly left.
View 4 Replies
Having issues with the brakes locking to the rotors after washing the vehicle? I washed it on Saturday afternoon, pulled it back into the garage and it sat there until Monday morning.
I back the vehicle into the garage, always. I started it up, put it in D and usually it will want to lurch forward if I don't hold the brakes firmly. Not today. I could not get the thing to budge. I sat there for a few seconds to make sure the parking brake was not on. It was not, as I never use that. My garage floor is the slippery concrete, plus with the tire shine that I applied, the wheels were just spinning.
After I managed to get the vehicle halfway out, I put it in reverse...that worked no problem. I put it back in drive and had no issues after that. Do I need to have the vehicle looked at? It only has 5,400 miles, and it was just in last week for the 5K mile service.
View 7 Replies
I know that the relay will make the turn signals flash fast when a bulb is out or there is a broken circuit, but I am not sure about how the brake light switch is causing this condition. I need to go and check all connections and bulbs, but I see nothing obvious at this point. When the brake pedal is NOT depressed, I get the normal interval of the turn signal. As soon as I touch the brake pedal, it begins to cycle very fast. Remove foot from pedal, and it goes back to normal.
View 5 Replies
I have 2014 F350, was previous flood damaged, the steering keep sticking when I turn it to the left, not always in the same spot, but sometimes it just locks and will not turn right, needs lots of jiggling and then it release, as I say in different places but always when turning to the left, never when turning to the right. Does this indicate steering gear fault or something else?
View 9 Replies
Just thought I'd ask, I was at the dealer last week and while there asked them to take a look at my brakes because they were making a slight screeching sound but only when first applied when speed was slow.
They said it all looked good but that the sound I was hearing was from grooves that had been etched into the driver's side front rotor. I find it hard to believe that my rotor would have grooves in it after only 21k miles, considering I don't track it or drive it aggressively that would have caused that.
View 4 Replies
I've had a 2006 Passat 4Motion for about 15 Months now and it just went in for it's 20k mile service. The dealer told me that the front pads and rotors were shot, and the rear pads needed to be replaced.
I've read that the front brakes are rather easy to change but my question is: are there any aftermarket pads and/or rotors that last longer than the OEM ones? I just don't think I want to do brakes every 20k miles. Now in regards to the rear brakes, apparently my rotors are okay but my pads need to be replaced. I've read that you need the VW "Vag Com" to do that and I'm new to VW software stuff.
View 24 Replies
On 8/18/04 VW told me that my 03' Passat (38'000 miles) needed new rotors & pads. I bought the car new. They told me that VW used rear pads that eroded quickly and provided new rotors on the house. I decided not to press my luck and paid for new pads. I look at my pads now through the rims and it seems dangerously thin and the edge of rotors has gouge all the way around. HAS ENOUGH TIME PASSED FOR A LEGIT REPLACEMENT ON THESE PARTS?
View 4 Replies
So I just did my rear brake pads and rotors a few days ago. For the last few months, my e brake hadn't been working well (have to pull it way up, and still weak).
While doing the brakes, I noticed the park brake arm was more or less seized on the left rear. I worked it a bit, and then my park brake worked perfect - 4 or 5 clicks, right on.
Then I noticed it isn't disengaging (brake smoke). I figured the ratcheting mechanism in the piston must be kaput.
So today I got a new (reman) caliper & bracket, installed it, and... still sticking. Cables are fine, the arm is moving fine. I'm now certain that the problem must be hydraulic, but what?
I would think that a master cylinder or booster would cause all the brakes to drag, or at least one axle worth, but that isn't the case. After a short spin on the freeway with little brake use, 3 of the brakes show 40 - 45C or so, and the sticking one shows 150C. (with an infrared thermometer).
During the brake job I noticed the left side was harder to turn in than the right, so I guess that could have been hydraulic back pressure somehow. Didn't seem to notice any damage to the hoses, they look pretty mint. master cylinder still?
I did the rear bearings at the same time. The bearing on the left was bone dry, probably from overheating in the past - I'm sure this POS stuck at some other time too, overheated and lost its grease. right side was fine but I figured might as well do them both.
View 18 Replies
My 2004 Pacifica (130k miles) was left parked for 2 weeks while we were away. Upon return it didn't wqnt to back out of the parking spot. After about 1/2 revolution the wheels made a clanking sound and hung up. Rolling back and forth freed things up enough to drive the car to the mechanic (about 40 miles). And after the first mile or so everything seemed to go back to normal, with no absolutely signs of anything not wanting to turn smoothly.. The mechanic thought that the problem had been that the brakes were sticking due to the car being unused and said nothing needed to be done. However, upon examination he found that we could use new front brakes and 2 motor mounts. He said that the need for brakes and motor mounts was due to normal wear and tear, and was not related to the wheels hanging up issue.
But now, immediately after installation of 2 new front rotors and pads and 2 new motor mounts there is a vibration/shudder when braking from anything more than 20-30 mph, which was never there before. The shudder is rapid and sometimes pronounced like going over the warning groves cut into the edges of pavement on the interstate. He thinks that this may be a sign that there is a driveshaft issue, and dismisses it as due to an out of round rotor since they are new. I don't know what to think. By the way, he has always been an excellent mechanic, with a great reputation and loyal following.
View 4 Replies
