I went driving today and for a moment I could engage/disengage the clutch pedal with little to no effort. It goes back to the normal force after 3-4 shifts.
It's the exact opposite of what's happening in this thread. [URL] ....
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 RepliesI have a 1986 Toyota Camry. I drove it for a year with no additional problems than when I bought it. I replaced the clutch when I bought it. However, It recently has had a new problem. The clutch pedal is going directly to the floor with no effort whatsoever. When this happened in the past it was simply out of clutch fluid, I was aware of the leak when I bought the car. Now it doesn't seem to be using any at all and I can only put it in gear when it is turned off.
I have replaced the clutch master cylinder myself and it didn't seem to solve the problem. I have tried to bleed the new master cylinder but no fluid is being drawn into the master cylinder from the fill cup on the top of it. I'm not even sure that this is the problem. I noticed that the place where the MC is attached to the clutch pedal is adjustable. Could this be a matter of adjusting this to drive the plunger inside the MC all the way forward? I am also having trouble understanding the whole clutch system. The MC doesn't seem to have anything to do with engaging or disengaging the clutch. The only thing it attaches to is the clutch pedal. Where does the clutch fluid go? Is there another place to fill Manual transmission fluid?
The A/C in my truck stopped working last year, and this year I intend to fix it. I believe the problem is with the compressor clutch because it was making noise as it would engage or disengage. It was making this noise for a good year or so, and then one day the noise stopped and I have no A/C. So I am only assuming its the clutch.
View 4 RepliesI think this is just poor dealer service, but I need a sanity check.
I have 93k miles on my Corolla. My clutch creaks like an old school bus when I engage and disengage. It's done this pretty much all along and I think I had another dealer successfully lube the linkage to quiet it down -- it was miles and years ago so I may be misremembering that.
My current dealer says all they can do for it now is REPLACE THE WHOLE FREAKING CLUTCH assembly to the tune of $1,300. Clearly, I'm not doing this. As long as it works, I ain't replacin' the clutch, but, REALLY?
My clutch went out on my 98 Dodge Ram 2500 4WD the other day. I limped it home shifting like a big truck timing the shifts w/out the clutch. I replaced the slave cylinder w/ an aftermarket that had a bleeder. Bled it and got the pedal back up and it still wouldn't disengage the clutch. I replaced the master cylinder and started getting pedal back until I let the reservoir get too low and now after plenty of tries, I can't get any pressure built. I get a stream of fluid, but no air. Bench bleed the master and start over? I'm at a loss.
View 5 RepliesI've got a 2000 F250, 5.4L 4x4 with the ZF5 5-speed transmission. Three years ago I replaced the complete clutch assembly, pressure plate, throw-out bearing, etc, and had the flywheel re-machined. Put it back in and all has been well. Only has about 15k miles on it. Earlier this week I went to drive it and all of the sudden it started getting harder to shift and by the end of the trip the clutch will not disengage at all when I push the pedal in.
Furthermore the pedal is much harder to push than it always has been. Checked the reservoir and it's fine. After some searching it seems to most likely be an issue with the master and/or slave cylinder either needing to be bled or replaced. Further reading revealed that bleeding and recommends just replacing the whole system, so I've priced that out. Was it a master/slave issue? Anything else I should check in case it isn't?
I have an 02' 2.0 Jetta Wagon, and the A/C is having some issues. Since I know close to nothing about A/C systems, I took it in to a few places to have it looked at. I've had the whole system Evac'd and recharged, and have had the low pressure fitting replaced (apparently there was a slight leak there), and the system is still not working.
The A/C worked fine when I first purchased the car a few months ago. Shortly after my 800 mile trek from Oregon, back to home, the A/C started to only work intermittently. The compressor would engage, then disengage, repeat...It seemed like a bad idea to keep trying to use it in its sad state so I stopped using it altogether. As I said, I had the system emptied and recharged, but it still only works intermittently. It sort of follows a pattern where upon start up it works longer, and switches on and off at shorter intervals, until it doesn't engage at all.
There are no strange noises from the compressor, and when it was hooked up to the machine, it proved to be performing its function well.
I have a 2001 Ford ZX2 with 170,000 miles on it. The clutch pedal doesn't engage the clutch until it is almost touching the floorboard. I thought it had a hydraulic clutch being a 2001 but I can't find a reservoir for the fluid so now I must assume now that it is a mechanical clutch.
1. Does they hide the reservoir on these ZX2's?
2. What could cause the clutch issue?
I've test driven a used 2003 (155K) I'm considering purchasing. But the clutch is so stiff, especially compared to my 93 Accord. What makes a new clutch, pressure plate a throw out bearing so hard to engage?
View 9 RepliesI have a 1995 Ford Ranger 4 cyl w/ hydraulic clutch, about 95k miles, and an intermittent problem. Normally, my clutch works fine, but a few times a year, normally during the summer, and normally only after driving for a half hour or more, it starts to act up. First, the pedal starts to feel a little spongy. Then, I'll depress the clutch, and when I release it, the peddle comes up, but the clutch does not engage; a few seconds later, the clutch engages fully instantaneously, which usually stalls the engine if I am stopped.
Then, when I try to reengage the clutch so that I can restart the engine, the clutch is very stiff, and I have to pump it a few times, at which time it will depress easily, and then I am usually back to the original problem where the peddle comes up but the clutch does not engage. When I finally make it home and the truck sits for awhile, the clutch then works fine again. I think it is the orig clutch. I have talked to several mechanics about this problem (including the Ford garage!), and they are mystified. One mechanic thinks that it is a problem with the master and slave cylinder combo, and can replace them.
1988 Acura Legend, 2.7L 6 cyl., 181,000 miles only do 6,500 miles a year to train station, parked inside, runs great. Last week parked out in hot sun, '90s, for 8 hours. At first, no problem. When did errand and returned to car, pushed clutch pedal and it would not return or allow gear to engage. "Jammed" into 1st, then could not shift, shifted slightly by pulling up on clutch pedal with my foot. Parked overnight, cool, next morning seemed to be fine and crept to mechanic. Mechanic road tested and found no problem and now seems to be working okay. Would parking in sun, high heat cause "clutch cylinder" to "seize" or "freeze"? Is there a "fix"? Also, increasingly hard to get parts for this car.
View 6 RepliesMy 01 GTi (12v VR6) was having some trouble shifting into, and out of, first and reverse so after a bit of research I decided to try adjusting the shift linkage as it seemed like a possible easy fix. After doing that I tried backing it up in the driveway and after a couple of shifts to different gears it ended up getting stuck in reverse. When I pushed in the clutch pedal to let it roll forward I noted that it seemed to be resisting rolling forward despite the steep incline. Once it reached a less steep incline it stopped rolling forward completely, so I'm thinking that it probably won't come out of gear because the clutch won't disengage all the way.
I've done some searching around and from what I've read so far it sounds like it could be a worn or damaged clutch fork, the hydraulic lines, master or slave cylinder, or even a broken clutch plate. What I don't want to do is pull the transmission and clutch, only to find that it was something much easier to fix.
My clutch peddle made a slight "snap" sound last night and now it is very difficult to get the car to engage in a gear while sitting still, while moving it does ok, but not nearly as smooth as it should be. The other odd occurrence is that while the motor is running and the car is not moving, you can't shift any gears at all, but as soon as you cut the motor, all 5 gears and reverse are easily accessible. Why the sound at the peddle and the trouble in the gear shift mechanism? I am only an advanced beginner with car repair, but I think think this is really bad... 2007 Honda Accord Manual Transmission
View 8 RepliesWorking on a 2002 Hyundai Elantra GT. 4 disc, no ABS. Problem is the brake pedal goes to the floor without much force. I bled all 4 lines, but no improvement. Rigid lines from the brake master cylinder to the rear wheels were very corroded, so I ran new lines. The old ones pretty much fell apart when I took them off the car. I also replaced the brake master cylinder. I tried to bleed the brakes again, but couldn't get much (if any) fluid pressure at any of the wheels. Yes, I found a couple leaks at the junction points for the rigid lines, but I re-flanged those connections and got rid of all the leaks. Still no real pressure when trying to bleed.
So, I tried a second, then a third master cylinder with a new attached resevoir. No improvement. I bench bled the snot out of this third master cylinder because the symptoms clearly suggest air was likely trapped somewhere in the system. I used a wood dowel to fully actuate the cylinder many times after all the air had been released while I had short clear hoses running from the master cylinder outlets into a little plastic cup filled with clean brake fluid. I wanted to make sure there was no way air could be in the MC, and no air drawn back in when I released the wood dowel.
Next, I quickly capped off the MC outlets and connected a hose to each brake line individually where they normally screw into the MC. I then let clear fluid drain through each line until it was spilling out clear of each caliper bleeder with no air bubbles. So, no lines are kinked, clogged, or contain air.
I took every precaution to keep air out of the system, yet when I push the brake pedal, there is still virtually no real pressure generated by the MC. The power booster rod is shoving the master cylinder in as it should. I don't think there's any problem with the power booster.
I've used gravity bleeding, manual "push & hold the brake pedal" bleeding, vacuum bleeding, and I'm certain there is no air in the lines or calipers. Still no significant pressure coming from the MC when I push & hold the brake pedal to the floor. It takes maybe 20-25 pounds of foot pressure, but always goes completely to the floor with all the bleeders closed. If the pedal is held to the floor, fluid slowly seeps from the bleeders. I'm used to it spraying when doing this on a healthy brake system.
I went to start my car this morning after not driving it for about three days and nothing happened when I pushed the start button. So I double checked to make sure it was in park, had my foot on the brake and again the car wouldn't start. The only thing that would happen is it would engage the accessories same as if I pushed the start button without having my foot on the brake pedal. I did notice that the brake pedal felt unusually hard as in, it would not depress more than a few millimeters. I decided to push on the brake pedal with considerable amount of force which resulted in it depressing maybe a few millimeters more. Then when I pushed the start button the car started up and the braked pedal sank a few inches like normal when the car first starts up. Everything was normal after this. Made a few pit stops on the way to work and the brakes felt fine and the car started perfectly normally.
I have had the car for only a week and a half. It's a 2012 isf.
My AC doesn't work right now, however, sometimes it works. It's very random, it doesn't matter if its hot outside or if its cool.
What happens is my AC clutch doesn't engage. when I turn ac on, it raises the idle for a second, and as soon as it does that, my ac compressor gets around 12 volts for less than a second, and the idle drops again. it does that in a loop.
My fans work fine, both high and low speeds, everything else works, all the fuses are good. I changed the pressure switch, didn't fix the problem. I also checked the ac coil and clutch. everything clicks and works. ground on the compressor is good.
Other odd thing - positive wire on the compressor constantly getting around 3 volts. What can it be and what else do i need to check?
148,000 miles, and yesterday my R decided it would no longer allow me to use first gear. It sort of starts to go in gear, but feels kind of mushy, not positive, and if I let out the clutch, the gears grind, but will not engage. All other gears feel and perform normally.
View 7 RepliesMy wife and I have a R and a rabbit, she drives the R mostly and i drive the rabbit mostly..... I drive further to work, anyhow the past week she told me that the clutches feel like they are slipping and when she puts it into drive sometimes it wont engage... or when she puts it in p it says in d...... anyhow off to the dealer it goes for who knows what and how long... and the car is stock....
View 24 Replies owner of a 2007 Passat 2.0T wagon, 6 spd manual, 32k km's. (leased) I'm having repeated persistent parking brake failures (won't engage, or won't disengage).
-About two months ago the parking brake would not disengage, error message on the MFD, yellow warning light and warning tone. Called roadside, finally got it disengaged by removing one terminal from the battery. Took it straight to the dealership, they "fixed" it by resetting the computer.
- The next day I have auto hold engaged, parking brake did not disengage when I turned the car back on. Had to turn engine on/off several times before it disengaged.
- Took it to the dealership again, had to get a rental car over a weekend while they diagnosed the problem. This time they changed some wiring and replaced the parking brake button.
- Next day the parking brake engaged ok but wouldn't disengage. Same routine on/off/on/off to get it to disengage.
- Back to the dealership again, they decided to replace the brake control module but didnt have stock.
- Last week I took the car back in (4th trip for this issue), they replaced the module and said it was fixed. Next day my wife got stuck in a parking lot with the parking brake stuck on.
- Called the dealership last friday and asked them to come pick it up this time, as my wife and I are sick of the inconvenience of this issue. (we share the car, both work, and also have a child's daycare to schedule around)
The problem is intermittent but not difficult to cause a fault. Can be caused when engaging, disengaging, or when the PB kicks in from auto hold when turning the car off. I try not to use it, but sometimes is necessary (parking on hills etc).
The dealership doesnt seem to know the problem and are just throwing parts at it. What recourse do I have for repeated problems? The manual recommends using this parking brake EVERY time the car is parked, so I don't think it's too much to ask to have it working properly.
I recently bought a 1997 f150 4x4 with shift on the fly. I bought the truck from an old man who parked it outside his house. I love the truck, but the 4x4 has been finiky. I have done a ton of research and i have done a bunch of testing. The vacuum system is working correctly. I have tested the solenoids and the front axle actuator is working properly.
There is some kind of electrical issue. It might be the GEM (i really hope not), but it might be the shift on fly switch itself.
The 4x4 will engage, but when i turn the switch to 2h nothing seems to happen. Driving in reverse doesn't work. But sometimes it switch from 4h to 2h, just by turning the truck off and restarting it. If restarting doesn't work, then i have to pull the 5 fuse, let it sit, then put it back in. I read that this resets the GEM. (Number 5 fuse, middle row, 5th from the top).
Resetting the GEM usually does it, but not all the time. Sometimes it will still be in 4x4 again after resetting the gem. And then what is really weird, after driving it in 2h (after the gem reset) then turned it off and restarting it, it will go back into 4x4. All this happens with the switch set to 2h. So I have been having to reset the GEM, each time i restart it. (This was going on for a day or so.)
Any easy testing i can do? Do you think it could be the switch on the dash, or more likely to be the gem? I hope it isn't the gem. I don't want to have to pull a fuse each time to drive my truck.