Lately my R is acting up, sometimes hard to get in reverse and shifting from 1st to 2nd is very rough. I looked at the cables , the left one towards the engine , the rubber bushings seems to be broken, lots of wiggle in there, is that enough to cause this? Is there any adjustments needed on the cables anyways?
View 9 RepliesNoticed that the transmission is cold (ie. sits overnight) it is hard, sometimes impossible, to shift into reverse. Specs on my gti: 14k miles, pretty much stock, manual trans...
View 1 Replies2001 VW Jetta 1.8t automatic.
Transmission has a hard time going into 1st and reverse. Also some times hits hard going into third. I have a CEL for a vehicle speed sensor? Was wondering if it's not the VSS but maybe one of the other tranny sensors?
Separate question. Same car has a rough idle issue. Occasionally stalls but intermittently runs normal always has a low idle around 600 rpm. I have a code for an injector on cylinder three.
VSS code : P0725 - engine speed sensor circuit malfunction
Injector code : P0203 - injector circuit open cyl 3
I have a 2004 Camry 4cyl with and Automatic Transmission. 193,xxx miles. I bought the car with 165,xxx miles. From time to time the transmission would take a little longer than normal to shift from 1-2 or 2-3. It has also had an issue with locking up the torque converter at speeds around 50 MPH which seems to bog the engine some. An adjustment of the foot on the gas pedal fixed both of these problems. (I just let up a little or pressed a little harder)
Well on friday it did something weird. It now clunks very hard when shifting into reverse. Also when in drive it seems to be in 3rd gear. The engine revs very high before the car starts moving but then it seems to run fine once moving and up to road speed.
I have heard that the Transmission may be controlled by its own Computer unit. Is that true? How do I get codes from it?
I have run my scan tool through the OBDII port and get no codes at all.
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 RepliesI have a 2003 Accent and it has been over heating constantly for about 5 months. After it started, we replaced the main radiator hose, thermostat, radiator cap AND a head and head gasket. It worked for about 2 weeks and then over heated again. It seems like there is too much pressure somewhere because the lid for my reservoir shoots off and all the coolant comes out. I'm just not sure where to look for a clog since it is coming out of the reservoir. It also recently started having transmission problems(?) or that is what I think it is... It won't go in reverse and has a hard time shifting sometimes. I'm not sure if it could be related or if it is the tranny also.
View 4 RepliesRecently my 2004 Santa Fe 2.7 AWD (~86k miles) has started to give a sort of hard thump when shifting from reverse into drive. It's fine going into any other gears and it shifts up and down normally. If I shift from reverse to neutral and then to drive it's fine.
I changed the transmission fluid when we first got the car at 40K miles with Hyundai Liquid Unobtanium SPiii fluid and again at 80k miles with Valvoline's SPiii offering. I just checked the transmission fluid level and it's within the normal range.
I can't tell if this is just drive-line slop or something else inside the tranny.
[URL] .... My engine has been making this sound for a while now I am at 125000 miles, what it could be and if i need to be worried about it? also, possibly unrelated, it has a SUPER hard time shifting into reverse, it gets stuck and it feels just super sticky shifting in and out of reverse. Sometimes I can't even get it to go into reverse without letting the car roll a bit. Also, at around 3k rpm the engine sounds a little grinder in any gear. 2008 Honda Fit Sport ...
View 19 RepliesI'm having problems with my 6r140 in my 2011, the truck is an early build around 8/2010 I believe.
After cold soak when shifting into reverse after allowing engine to warm a bit the transmission almost always slams hard into reverse.
After that shifting from 1-3 is awful, the transmission will try to go into 3rd but downshift to 1st then fail to go back into 3rd multiple times. This situation is extremely dangerous when trying to pull into traffic.
Oh and once the transmission gets into 3rd it will skip 4th and go right into 5th. There is only 94k miles on this transmission/truck.
I just bought this truck about a month ago, does this sound like an issue with the solenoids in the valve body?
I'm very mechanically inclined and can swap them if need be but now we're talking few hundred in solenoids and then getting the trucks pcm flashed right?
Also fluid has been changed and I used mercon lv.
Tranny started acting funny recently...shifting hard into reverse at first, then last night it was like it was stuck in high gear or slipping on the way home. Limped it home and took the following codes:
P0743 TORQUE CONVERTER CIRCUIT ELECTRICAL
P0750 SHIFT SOLENOID A MALFUNCTION
P0755 SHIFT SOLENOID B MALFUNCTION
P0760 SHIFT SOLENOID C MALFUNCTION
P0765 SHIFT SOLENOID D MALFUNCTION
P0962 PRESSURE CONTROL SOLENOID A CONTROL CIRCUIT LOW
P0966 PRESSURE CONTROL SOLENOID B CONTROL CIRCUIT LOW
P0970 PRESSURE CONTROL SOLENOID C CONTROL CIRCTUT LOW
My 2000 Jetta gls vr6 automatic was not shifting into reverse until it warmed up a bit, so I did a filter and fluid change, car level, warm pumped fluid while shifting gears. No problem. Next morning no forward fear, guess I split the gasket by over tighting. Had it towed home. Oh, tried to get to work, adding fluid made it go. Now now gasket and fluid. No gears at all. Generic code reader said electric malfunction on every shift solinoid, torque converter lockout and something about shift timing malfunction. Basically everything connected to ribbon harness. What's up? Did I fry it. Also I have a 2002 triptronic from my 2002 vr6, suppose that's not a bolt on?
View 1 RepliesTwo months and 2500 miles on my GTI and I feel like I finally know what the DSG is going to do most of the time. Driving with a cold tranny? Expect some delayed clutch takeup and very noticeable downshifting. Downshifting to pass? Goose the throttle a bit before hand to let the car know what you want. Shifting from reverse to drive? Better come to a full stop. EXCEPT! My DSG will still seemingly stall during this transition roughly 1 out of 3 times. I cannot find any rhyme or reason to it and now basically have to sit stopped in N for a good 3-5 seconds before shifting into D to keep the car from doing that quick surge and stop maneuver. I feel like it might be something with the timing of when I press or release the brake. I love every other aspect of the car which is why it's so annoying having to explain to passengers why the transmission in my 30 thousand dollar hatchback just fell on its face.
View 8 RepliesSpecifically only from 1st to 2nd. I'm kinda knew at this kinda stuff and just started school so I haven't gotten to this part of knowledge. Looking for a solution I've heard two possibilities. For a GTI 12v vr6.
View 1 RepliesIs it normal to occasionally feel a little vibration or feedback in the shift knob when putting the car into reverse? It happens whether the car is in the "Warm-Up" phase or not, and seems pretty random. Happens about 25% of the time. It doesn't last but a tenth of a second, and it just barely makes an audible noise when the window is rolled down. This is my first manual transmission car so I just don't have the experience to 'diagnose' this. And no, I'm not trying to put the car in reverse while the car is still rolling forward.
VW Golf 5-speed....
I have a 2010 GTI, and im curious as to how long a clutch CAN last.
This is my first manual car and i had a bit of a rough start the first 30 days. No stalls, just a little bit rough in shifting. Im a "Pro" now as in i dont shift rough, etc.
60-80,000?? Or way less?
I have a 2000 Jetta GLX VR6, automatic, that I have been going over for my son. The passenger side mirror doesn't adjust when I shift into reverse. I moved up,(towards the top of the housing) a little. Shifted to park and then back to reverse and it moved up again and doesn't return. I have changed the mirror switch, the mirror motors, and have dis-connected all the electrical plugs on the transmission. I figured the plugs needed to be plugged and re-plugged to clean the terminals, but no luck. Is there a switch or sensor that needs to be replaced on the transmission? All the fuses are good. What needs to be done?
View 5 Replies1999 Jetta MK4 with only 124k miles on it. Everything is fine with the car except when the car shifts from 2nd to 3rd it is jerky/violent/forceful everything else is good with car except check engine light is on but I don't really care about that and I'll go check with autozone to see what the code is. I am able to feather the gas when I know its going to shift and I can make the shift pretty smooth. My question to all the experts is does this mean that this tranny is on its last leg or does it still have a lot of life left in it. My old Cabriolet did it for years and never was a problem.
View 5 RepliesThird owner with about 81k, sometimes when I go to shift into sixth it seems like there is something stopping me about half way into normal position. Normally I have to go back to neutral and then try again. I don't have this issue with the other gears.
second question, I've noticed under deceleration mostly or going slow over bumps that I can hear a tin style rattle. Now the last couple days when I start the car with or without AC running there is a constant rattle making me think that whatever was rattling over bumps is about to make a run for it when I hit a big bump or something.
Car in question is my 2003 Jetta 1.8t with the 09A 5 Speed Automatic. For the past 2 or 3 months these have been the symptoms: 1st to 2nd gear, very hard shift depending on RPM's (Higher the RPM's the harder the shift) 2nd to 3rd gear, not really hard but it kinda 'flares' the gearbut still shifts. All other gears are fine, although if you accelerate hard out of 4th it will have a little bit of a hard shift. I'm thinking either solenoids, or the speed sensor?
View 1 RepliesI have a 2010 euro spec GTI DSG with 140.000 km (86.000 miles)
The problems i have..
- Rough vibrations.
- The car starts quick but there is big jolt when the engine fires, shifts or turns of.
What has been done to the car
**New mechatronic 30.000 km ago (replaced with new revision on warranty)
** Oil , filter , plugs
** Carbon cleaning by myself yesterday
** DSG calibration done
** No errors codes
I am thinking its mounts to the engine or transmission? Other things I am thinking of ...
- Coils packs?
- PCV?
- MAF?
The car is little low on power as it struggle on uphills on low speed, but much better after carbon cleaning.
I'm wondering if this piece of plastic has anything to do with it,also it is a 2001 jetta 2.0 .I just don't know what it is, or what to look up as a part # or name.
About 2 months ago,it just started acting up, shifts fine, but I have to push down hard 75% of the time to get it into reverse.