Golf IV R32 :: Fluid Boiling And Loss Of Power In Hard Cornering
May 13, 2016
Have some issues with my power steering pump. When I purchased the car i discovered it had brown fluid in it. Replaced it with green type and tough the pump had taken no damages from it. Did a track day with slicks (Toyo R888) and got problems with fluid boiling and loss off power in hard cornering.
My first thought was that the pump was damages by the wrong fluid. Before I got around replacing it the pump started making more and more whining sounds while driving on normal road with road tires.
Therefor I replaced the pump but the sound still continues. I changes the belt tensioner as well since the bearing could cause some issues like this as well. But the pump still struggle on normal road usage.
Could the steering rack be damaged with some internal leakage from the wrong fluid on it when purchased? I run DLI engine mounts, I can't see how but would that affect the sound from the pump?
Could there be any bearing on the belt (water pump/ac/alternator?) causing this issue? When running idle the belt runs fine with out any typical shot bearing sound.
View 2 Replies
Advertisement
As I got to work today, I took the off-ramp particularly enthusiastically. At the very end of the ramp, I got a huge red warning on my MFI saying 'Fuel Pressure Low, Engine off'. Error message was on for maybe 2 seconds. I checked my tach, no dip below 2k, throttle response was normal. Car has run fine after that.
My hypothesis of this happening: I was low on fuel. Indicated range was 40 miles. When I took that corner hard, gas must have sloshed around in the tank in a way that the fuel pump didnt 'find' any gas for a couple seconds - causing the error. As the fuel settled in the tank, got back to normal.
View 8 Replies
I get a whine when I'm driving hard under low speeds and accelerating (only when really aggressive). Is this cause for concern? Haldex whine I'm assuming?
View 3 Replies
2.7 Power Steering Fluid boiling/foaming leaking out a reservoir cap!
1) Recently had Timing Belt/Water Pump and spark plugs/wires replaced.
2) Issue started immediately after.
3) Removed most of old PS fluid, cleaned out reservoir w/brake cleaner. NOTE: nothing appeared to be clogging reservoir. Refilled with new PS fluid. Repeated these steps a second time. This appeared to immediately resolve the issues for several weeks.
4) Now the power steering is getting rough and noisy again. Also, the PS reservoir is leaking out of the cap worse than before. It looks like the fluid may be "boiling", but it is definitely foaming up pretty badly.
What my issue(s) may be?
View 4 Replies
Having problems where sometimes the car won't go into gear, other times it's fine? The problem started after some hard acceleration in 3rd, there was what felt like a momentary loss in power. I dipped the clutch as I thought a boost pipe had popped off, all was fine (still seeing boost when revved). After this it got progressively harder to get gears, finally resulting in not being able to get into gear at all.
I found I could get it into 1st with the engine off and could go up gears normally, but couldn't change down without stopping and turning the engine off. The clutch is working fine, the biting point is normal. The problem seams to come and go randomly, it will work fine for a while and then start playing up again. When working the gearbox feels normal, there is no grinding or wining noises. I can move between gears normally and do clutch less gear changes.
There is now a vibration which can be felt at 1000rpm when stationary. It feels like it coming from the engine/gearbox and seems like something is out of balance as it shakes the whole car. The car is on 91k, supercharged running 470hp & 370lb/ft (at flywheel) and is fitted with a Spec stage 3+ clutch and solid flywheel.
View 10 Replies
I have a '99 E350 that sat for a winter. When I started it up, it appeared to be overheating and boiling over. I didn't have time to mess with it, and it sat for another year. Today I tried to figure out the issue and determined that I have trains fluid in the coolant. Pulling the trans dipstick revealed a white milkiness on the dipstick, so I'm guessing the trans cooler/radiator failed and the two fluids have mixed.
My question is, is the transmission salvageable? The van has not been driven in this condition, so I'm hoping there is hope. Obviously, flushing both systems (multiple times) is in order, along with a new radiator. But is there any hope for the transmission? I'd hate to spend the money flushing it all multiple times if it is a lost cause.
View 13 Replies
I just noticed that when I am taking a hard right turn such as getting on the freeway or exiting, I hear random clicking noises in rapid successions in random intervals. the traction control alarm also lights up when this happens. is this normal? it sounds like relays are going crazy. I have not tried left turn yet since there isn't many opportunities around.
Clicking happens under hard cornering which in turn causes TC light to come on and when still under acceleration.
View 12 Replies
My wife was driving yesterday from work and suddenly felt the steering becoming hard to steer so she was able to drive home but barely made it to our driveway (very hard to steer). I saw fluid dripping down the right side of the car. I opened the hood and saw lots of brown fluid spilled all over. Power steering fluid reservoir was empty. So my question is, is this primarily caused by power steering pump failure causing spillage of fluid contaminating the drive belt causing it to slip (car overheated a little bit) or Serpentine belt failure (120,000 miles with original belt) causing power steering pump to fail and eventually leak fluid.
Photos: [URL] .....
View 6 Replies
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
View 14 Replies
I recently had the high and low pressure tubes on my power steering fail causing a total loss of fluid. After about a week of living with manual steering, I brought it in and had the tubing replaced. Everything worked fine, though the steering felt a bit sloppy to me. Today, on my way home from a 100 mile trip, the car decided that turning left just wasn't something it wanted to do.
So to turn left, I would have to back up and turn the wheels to the right. Not exactly an efficient way to drive in traffic. Do I try to get the car back into my mechanics place to see if he can fix it for a reasonable amount, or should just bite the bullet and look for a newer car? BTW when I had brought the car in for the tubing replacement, they showed me where the bracket holding the strut on the left had begun to crack, probably from driving without the power steering. 1998 Malibu LS ....
View 3 Replies
Let's say I accelerate hard and hit some potholes and/or bumps in the road. this causes wheel spin/loss of traction. could anything be damaged if i keep accelerating past all the bumps while the traction control keeps trying to stop the wheels from spinning freely? I am talking about throttle to the floor in 2nd gear over bumps/small potholes
View 24 Replies
I have a 2000 gmc jimmy 300.000 km 4.3 vortec .starts ok, even when cold idle smooth but when I accelerate past 2000 rpm it has a complete loss of power. I bought a fuel pressure tester key on 2 seconds 60 psi when I start the vehicle and running 55 psi. I took it on a road test it stays at 55 psi and has a hard acceleration and will go to 60 psi ,and then starts to break up my first question is how can I block off the return line to the tank, there's no rubber hose in any of the connections just steel lines and hard plastic with push connectors, is there a plug that you can buy or how I can block off the return to see if the pump will build pressure to 75 psi to 80 psi will this will tell me whether the pressure regulator is faulty or the fuel pump needs to be replaced.
I have a manual its a Haynes for chevy blazer gmc from 95 to 2004 it says with central sequential fuel injections (csefi) key on engine not running it should be approx 55-61 psi the engines running at idle it should decrease through 3 to 10 psi according to this manual i am within range but i have read on other posts that it should be 60-65 would you say that my 55 psi reading is okay? or should it be 60-65? also when i blocked the return line should i get a reading of 75 or higher? if the reading goes up does that mean that the fuel regulator is faulty? and if it doesn't go up does that confirm that the fuel pump is the issue?
View 3 Replies
When ever I "Brake boost" it kills the power when I hit the brake and gas hard at the same time.
View 3 Replies
I blew a power steering cooler line yesterday and lost a bit of fluid. Removed and replaced the line, consequently losing most of the fluid in the system (during line replacement). Re-filled the system and now i have great power steering when driving but none at idle. If I bring my RPMs up about 150-200. I get it back in full force. Could my PS pump be on the way out or might this just be air in the system?
View 3 Replies
I've been noticing severe power loss lately . I know the 12 camry i4 has a bit of lag when acceleration but it's a bit worse now . I do have weapon r header , injen intake and magna flow muffler. I've cleaned the intake filter but sometimes the car feels as though it doesn't want to go then it does. I have to push the pedal down hard . I also have res delete.
View 9 Replies
My 2004 Elantra occasionally won't start. When I hold the ignition on Start, the radio loses power (but the dashboard doesn't) and nothing else happens. Sometimes, tapping the gas pedal will suddenly cause the car to start. Once, I had to stomp the pedal to the floor before it would work.
I just replaced the battery (and positive cable end since it was corroded in place) and recently replaced the spark plugs (which were badly burnt). There is a check engine code for "catalyst underperforming" which seems unrelated.
I suspect my car has fuel delivery problems. It occasionally sputters while idling and often has power loss while driving if I try to accelerate hard. It seems to have trouble shifting into 4th gear from 3rd or 5th, but that may be another issue entirely.
What I should check to diagnose this, or replace to resolve it?
View 7 Replies
I have a 2006 town and country with a 3.3 and 220,000 miles.
Last week I was having some hard starts and loss of power on acceleration. My check engine light flashed during one episode so I had autozone check the code and it showed a misfire. I changed out my plugs and wires and that solved my issue. It started and ran like new.
Yesterday, I was running errands and my charging light came on. I was about ten miles from home and I decided to go for it. It was night so the headlights were on. Along the way, everything started to dim. Headlights, dash lights, airbag indicator came on and then the van just died. I walked the final mile and we towed it home.
The alternator and battery were both replaced last year in November making them both one year old. AC Delco battery 660 cca and I had a very reputable alternator shop rebuild the alternator.
So before I towed the van home, I hooked up some heavy duty jumper cables from a running chevy venture and let it charge 15 minutes. After the 15 minutes it was just clicks in rapid succession.
I hooked it up to a trickle charger overnight, 12v 2 amp setting. This morning, the van started, idled fine for about five seconds and then started trying to cut out. I kept it running by giving it gas but after about twenty seconds it stalled. I tried to restart and nothing but the rapid clicks. Three more hours on the trickle charger and the same exact thing happened. It started, began to stall, quit and then wouldn't restart.
I noticed today that the power steering reservoir was leaking a decent amount of fluid down onto everything around it including the coil pack. I replaced this today and used brake cleaner to clean all the surrounding components.
After doing some internet sleuthing, I found a thread with the same problem. For this guy, he had a disconnected ground from the negative battery terminal. I chased mine down (G101) disconnected and wire brushed it all clean. Put it all back together and still the same problem.
Here is what I have discovered:
Trying to jump it from another vehicle only results in the clicks. This is true whether the jumper cables on the dead battery are on both terminals or the negative is grounded on the motor. If the battery were the problem, I should be able to jump through it. If the alternator were the problem, I should be able to start with a jump.
After charging the battery, it will start once but then die soon after. Battery with the key off will read just under 12 volts (11.9, 11.6). With the key on, it will drop to the 8's (8.6, etc.) I have not yet had the battery or alternator bench tested. I plan to start with the battery in the morning.
It seems to me that the alternator wasn't charging the battery or it wouldn't have just killed the battery as those accessories should be powered by the alternator. It shouldn't be a starter issue since it will start after being on the trickle charger.
View 6 Replies
1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 Replies
At times when taking my beloved R aggressively through a long, tight turn (e.g. highway cloverleaf on ramp), usually while while accelerating, I get an oil pressure warning message (turn off engine immediately)...which goes away immediately once I straighten out/ease off on the aggressiveness.
Is this just an indication that oil is a little low? I can't say specifically what the interval vs. the last oil change was when I've had this happen.
View 10 Replies
Everytime i accelerate medium to hard with the CEL on like this it starts flashing and i loose power. Feels like a sputtering (in idle too). Fuel injection system cleaned and was 75% better for 1 week, but now back to same old. Reset CEL and comes back 100-200 miles later. Cam tensioner? Fuel filter? Coil packs? One of my fan clutches is pretty much out, related?
New spark plugs, maybe needs a tune up...supposedly TB was changed, but i have 106K on 1.8T 2001.5 Passat. New oil pump, timing belt tensioner put on. However A/C belt snapped and had to be put back on then tightened to work. Maybe they didn't adjust correctly at shop the timing belt tensioner?
View 3 Replies
VW Golf 2000 2.0 GLS engine auto. 158,000 km
Observation 1: The coolant flange broken 3 times, which appear to be caused by pressure inside.
Observation 2: I drove it today to see the problem. During normal driving upper hill, the temperature turned to be higher than normal. 1 or 2 minutes later after red light, I turned off the engine. And then driving for 2 minutes after the green light, the temperature read appeared to go back to normal (a tiny bit higher than normal). Further driving 5-7 minutes, the temperature reading went to the high end again. So I stopped, opened the engine cover and can hear water boiling sound inside the engine. The coolant in the expansion tank was much higher than normal (above the maximum). The coolant is Prestone (not G12).
I would guess that coolant is not flowing inside. But the problem appears to occur randomly. A water pump issue? (replaced at 90,000km) Or could be the thermostat? Why cannot the pressure be released automatically?
View 7 Replies
