So i was driving home from work yesterday and out of no where i couldnt get the shifter to get over to 1st or 2nd gear. i had to wiggle it around and push down on the shift knob and it eventually went over. Happened a few more times yesterday and like twice on my way to work today. It feels kind of sticky or something, not really moving as freely as it used to. What could be causing this?
View 6 RepliesI recently changed the bushings and installed SS kit. I don't know if this was the case before, but now while in any gear, i can still move it approx half inch to the right and half inch to the left.
I checked everything and all screws are tight. Could it be that the shifter cables need adjustment?
The issue with the car is that the tranny won't go into any gear. With clutch in or out. I had very little play left or right or up and down. Not sure what could be wrong. The car has 120k miles and no mods.
View 2 RepliesI have the 20th anniversary GTI with the 6-speed manual at 90k miles
I have the Dieselgeek Short shifter installed so for the most part my shifter is nice and tight/precise. However, I have some play in the shifter while it is in gear and I understand that this is normal for a car as it ages. But I assumed that the Dieselgeek would've solved all the gear slop in my shifter, and I was wrong.
So is there a part I can replace to tighten it back up?
When the car is in gear it's great! Or at least it seems great. However, trying to place the Shift Lever in the car into the gear "slots?" is troublesome.
It feels as though there is a wall in the way for each gear, and i have to force my way through the wall. It's not absolutely Terrible, for i've been driving like this for months. But i want a smother shift! I want to be able to just slide the Shift Lever into gear without any hangups or major resistance.
Double Clutching seems to work, however it might just be from the small loss of RPMs through the process of double clutching.
Personally I would rather not have to double clutch just to see a slight improvement. I have big feet and they constantly are rubbing on the floor mat as well as the plastic above the pedals, so double clutching always feels like i'm wedging my foot into a hole, then back out and in, before i can go into another gear lol.
The problem is only a real issue when i'm in higher RPMs giving the car more gas. I.E. after a fast launch in first, shifting even around 5500 puts a WALL up on second gear making it impossible for me to get it into second gear, after not getting it into second i usually throw it in third, and essentially lose all the acceleration i had from the first gear launch.
As well is there anyway to make the clutch a little stiffer? She grabs fine, i just like stiffer clutch, it requires less of me trying to wedge my huge foot on the pedal.
It's an un-molested MKIV Jetta VR6 with 167k.
My problem is that it pops out of 3rd gear when I let off the gas. I have had this problem before so any tips on setting my shifter linkage?
View 5 RepliesMy03 GLI will not engage first or second gear.
This morning, i was having some issues getting the car in reverse, but it eventually engaged and is fine now. I drove to the barbershop, and on the way home, the shifter stopped engaging 1st or 2nd gear. it moves freely into position (TOO FREELY) and all other gears will engage. common sense tells me that the clutch is fine and the problem is with the shifter.
I have a 5 speed 01 wolfsburg. I was about to leave my driveway tonight and went to shift into 1st and the shifter was all loose. I could not shift into any gear, the shifter was just flopping around. Earlier in the day the neutral jiggle was much looser than it usually is, which I thought was peculiar.... So I guess that was it breaking.
Question is: how do I fix it? I looked under the hood and all of the linkage to the transmission looks good, I think it has disconnected/broken under the shift knob... I've looked around online and cant find anything for this year... or replacement parts for that matter.
I guess im going to have to get the car up on jacks and remove the heat shield to get to the bottom side?
It happens when there's side to side movement or any gear change. I've tried spray/grease nothing seems to be working. I've read on other forums people replace everything under the boot only to have it return in a few months. I would really like to have this this squeaking gone. Cars a 2012 GTI
View 13 RepliesI'm having an issue with my clutch and I'm really in a hole. Two days ago I was driving my car and everything was fine. Later in the day the shifter got stuck and would not budge out of 5th gear. Eventually it popped out. Driving like normal again and then yesterday I was on my way home from work and all hell broke loose. I was a mile away from my house and the car would not shift into any gear without a fight.
I also at this time lost my clutch pedal. It went really soft but did come back up.. it would not engage however. Limped it the rest of the way home and took a look at it. What I came across was a full brake/clutch reservoir, no leaks around the slave, and I didn't see any leaks around the master. I will say that after the car sat for about 10 mins the pedal felt normal again but quickly went soft after a few pumps.
2.0 AEG 5spd. Trans code DZQ if any of that would be relevant..
I have a 2000 Golf GLS which I tried to replace the shifter solenoids on and since I replaced them it shifts very very incorrectly it almost feels as if it starts in 4th gear and works its way to 1st.
View 2 RepliesI have a 2004 2.0L Jetta with a 5 Speed manual transmission.
When shifting into third gear sometimes I push the shifter forward and it does not want to move all the way forward. It feels like I am pushing the shifter knob against a wall, or more accurately the bottom of the shift that pulls the cables feels like it is hitting a wall. If I pull it back out and press it in hard it will go into place sometimes.
This also solves the problem: While the shifter is mid shift into third, at the wall/ at the point of resistance, I let off the clutch slightly to give the flywheel some friction. This rolls the transmission a bit and allows third gear to slide into place.
I have experience with a MK4 Audi TT 1.8T that cam with a 6-SPD and it at had a 1-2 and 2-3 synchronizer issue (The one where the nipples are worn and it grinds at higher RPMS because they can no longer make a firm handshake). The issue I am experiencing is not that.
Could it be the transmission cables? Could it be some other cogs in the transmission? - If so does this mean I need to buy a used one? My car has 180K miles on it with the original clutch.
I picked up a 2004 GTI not long ago for pretty cheap because it had a few issues. I am working my way through them. However, having 3rd gear issue.
All other gears are perfectly fine but there is way less play in the shifter in the 3rd gear position and I have to hold the shifter in position until the clutch is engaged (pedal up) to avoid the gear grinding. Once the clutch is engaged it stays in 3rd gear fine. It doesn't matter if I am moving from 2nd to 3rd or 4th to 3rd. Same deal. I have aligned the shifter several times using to proper procedures with no effect.
It never grinds 3rd with the clutch disengaged (so the synchro is fine?) and it will bang shift no problem. Oh and the clutch is less than a year old. It was installed by a shop before I bought the car. It's not really a big deal, but I would like to fix it. If I have to swap the trans that's fine, but need to figure out if it is a trans or linkage issue first.
98 Jetta TDI hydraulic system ... We just received this vehicle from my mother in law, who is not driving any more. It's a cream puff--79,000 miles, beautiful condition. Problem is the clutch engages lower and lower to the floor, and eventually the shifter gets stuck in gear. The brake pedal slowly sinks to the floor when at stops on hills. Our mechanic tells us these two are connected because both the clutch and brake run off the same hydraulic system.
1st time he said the fluid was filthy, and he emptied the system and put in clean fluid. Worked for a little while and then we were back where we started. Second time he replaced a couple parts on the clutch, replaced this fluid, and this time it ran like a dream for a little over a month. Then the problem just returned. Again he says the fluid is filthy, and now we are looking at replacing the master cylinder and again changing the fluid. The theory behind why this is happening is that my mother in law let the car sit for half a year before passing it on to us. She didn't do much driving the 6 months before that either. I've done research, and this doesn't appear to be a common problem by any means on these cars.
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.
I have to replace my gear shifter and have the new one alread an OEM part could some one point me to illustrative instructions on how to change this basically it's the top part which you press to shift from park to drive, reverse and so on.
View 2 RepliesI drive a 2007 Ford Focus (manual trans), and it's been acting funny lately.
Here's the problem: Lately, when I start the car and try to put it into gear (either 1st OR R,) the shifter won't budge. While the engine is off, I can put it in gear just fine. After I wait for a little, turn the car off and on again, etc, I can get the shifter into gear if I really push it HARD. (I know I probably shouldn't do this, but... I was terribly late and desperate!) Okay, so I get the car into first and manage to pull out of my parking spot without having to reverse. When I go to get into second gear, I've still gotta push the shifter REALLY hard (again, bad!! I know!) but maybe a little easier. Where I live, it's stop-sign city, so I have to stop and go a lot, and within a few minutes of this (maybe 3 or 4 cycles of N, 1, 2, maybe 3, N) I can shift smoothly again and the car feels totally normal.
The strange thing is, this happens sporadically, and I can't seem to see any external factors that correlate with the problem, except that it seems to be worse when the car's been sitting for a couple days. Sometimes the car shifts just fine, and sometimes it won't get into gear at all. In general, the car's in pretty good shape: no accidents, scheduled maintenance, etc. I guess the only caveat is that a couple years ago, TWO people learned to drive stick in this vehicle, so maybe the transmission has taken some abuse.
The shifter will not usually stay in 5th gear for very long. The clutch and flywheel were replaced a few weeks ago just before i purchased the car but this problem has only cropped up in the last week. Could it be shifter linkage adjustment?
View 3 RepliesOK, I recently noticed a fairly loud clicking noise coming from the transmission (or the gear lever?) when you hit the brakes and again when you release them (only when at or near standstill). I'm pretty sure that it's the lock for the transmission so you can't start it without hitting the brake, etc., but I never heard it before. Should it be that loud? At first I thought it was my CD's in the console hitting the side when I was braking, but realized it does it when standing still and you can feel it in the shift lever. Maybe I'm overly paranoid, but I've never noticed this in any other car.
View 20 RepliesSo long story short I picked up a 2003 Hyundai accent 5 speed 80xxx miles for $1,000 almost two years ago, vehicle has been running great but the shifter always felt loose and it feels really weird going into second (kinda like the shifter really falls far into gear) I was online searching and found other different type of Hyundai vehicles with the same issue and they replace the shifter bushings oem or after market and fixes the issue. I called hyundai and gave them my vin and they told me for my vehicle they don't sell the bushings , i would need to buy a whole new cable.
My questions is am I looking at the correct place to replace my shifter bushing on the trans or is there something else I should be looking at? Shifter has been getting to the point where it hurts my wrist to shift, I've already replaced the trans fluid and its not hard to go into gear, just feels loose and if I try and go fast and shift fast the car will probably grind second due to the shift lever.
i have an 83 gt celica and i am have trouble getting the gear shift to go into 3rd gear. I can do it if i shift slowly, but doing this fast risks shifting into 1st or getting jammed between 1st and 3rd.
i have attached a link to a diagram of the shifter parts and this contains more info on the car and engine type if needed. My question is what exactly do i need to replace to make it easier to shift?I have removed the boot and the gasket just to look inside and see if something looks bent, but I have not taken out the retainer or the plate below, but i am thinking that is the piece i need to replace.